From Introduction: "This report presents the results of an analysis to determine the coolant flow and pressure requirements for a particular return-flow turbine rooter blade design utilizing hydrogen, helium, or air as the coolant."

From Introduction: "This paper presents results of an analysis of shear, bending-moment, and torque loads measured on the vertical tail during rudder-step, rudder-pulse, aileron-roll, and steady-sideslip maneuvers. In order to assess effects of Mach number and altitude, the maneuvers were performed at altitudes of 15,000, 25,000, and 35,000 feet and Mach numbers from 0.49 to 0.82."

Report presenting a friction, wear, and endurance-lift study made with bonded films of mixed oxides containing lead monoxide (PbO) as the main component. The coatings lubricated over the entire temperature range, but were far more effective from 500 to 1250 degrees Fahrenheit than at the lower temperatures. Results regarding the effect of silica additions on coating formation, determination of coating composition, effect of coating thickness on friction and wear, effect of temperature on friction and wear, and endurance properties are provided.

Memorandum presenting force tests that have been made of airplane configurations with a thin swept wing incorporating several wing-contour modifications forward of maximum thickness. Both longitudinal and lateral characteristics are provided.

Report presenting an investigation at subsonic, transonic, and supersonic speeds of the effect of lip shape on drag, pressure recovery, and mass flow of a nose-inlet air-induction system. Four lips of varying degrees of bluntness were tested on a fuselage model at a range of Mach numbers and angles of attack. Results regarding pressure recovery, net drag, and analysis are provided.

Report presenting a free-flight investigation to determine the effect of wing camber and twist at Mach numbers from 1.4 to 2.1 on the lift, drag, and longitudinal stability of a configuration with 52.5 degrees sweptback wing of aspect ratio 3, and inline tail surfaces. Results regarding drag, total normal force and pitching moment, and wash at the horizontal tail are provided.

Memorandum presenting the detailed blade-element performance of a five-stage axial-flow compressor for analysis purposes as well as to provide a contribution to the growing body of information necessary for continuing improvement in designing compressors. Results regarding overall and stage performance, blade-element performance, rotor blade-element performance, stator blade-element performance, comparison with design, consideration of boundary-layer blockage effects, and solution of equilibrium equation are provided.

Testing was conducting to evaluate the effects of support interference on the drag characteristics of two bodies of revolution at zero angle of attack at Mach number 1.5. Drag and base-pressure measurements are made for a variety of Reynolds numbers to determine the effect of varying the length or diameter of the rear support.

An analysis of the off-design performance of shock-in rotor-type supersonic blading is presented. The over-all losses are assumed divided into two groups;normal-shock losses, and external-wave losses. Throughout the range of relative entrance Mach numbers from 1.35 to starting, the largest losses can be attributed to the normal shock. An improvement in performance would be expected with a reduction of the normal-shock losses by the introduction of external compression waves.

Report presenting testing on 31 airfoils to determine the effects of thickness, trailing-edge bluntness, boattailing, and forward profile on the aerodynamic characteristics of thin airfoils, and to provide a check on available theoretical methods. The airfoils were 2, 4, and 6 percent thick and were tested at two Mach numbers at three Reynolds number in clean condition and one with transition fixed.

As part of a general investigation of propellers at high forward speeds, tests of two-blade propellers having the NACA 4-(5)(08)-03 and NACA 4-(10)(08)-03 blade designs were made in the Langley 8-foot high-speed tunnel through a range of blade angle from 20 degrees to 60 degrees for forward Mach numbers from 0.165 to 0.70 to determine the effect of camber and compressibility on propeller characteristics. Results previously reported for similar tests of a two-blade propeller having the NACA 4-(3)(08)-03 blade design are included for comparison.

Powered models of three different flying boats were landed in oncoming wave of various heights and lengths. The resulting motions and acceleration were recorded to survey the effects of varying the trim at landing, the deceleration after landing, and the size of the waves. One of the models had an unusually long afterbody. The data for landing with normal rates of deceleration indicated that the most severe motions and accelerations were likely to occur at some period of the landing run subsequent to the initial impact.

"This report combines the wind tunnel results of tests on four control surface models made in the two wind tunnels of the Navy Aerodynamic Laboratory, Washington Navy Yard, during the years of 1922 and 1924, and submitted for publication to the National Advisory Committee for Aeronautics May 7, 1927. The purpose of the tests was to compare, first, the lifts and the aerodynamic efficiencies of the control surfaces from which their relative effectiveness as tail planes could be determined; then the elevator hinge moments upon which their relative ease of operation depended. The lift and drag forces on the control surface models were obtained for various stabilizer angles and elevator settings in the 8 by 8 foot tunnel by the writer in 1922; the corresponding hinge moments were found in the 4 by 4 foot tunnel by Mr. R. M. Bear in 1924" (p. 429).

Report presenting an investigation in a mixing-zone apparatus to determine the effects of jet flow on two-dimensional base pressure and the development of supersonic channel flow about a two-dimensional base, with and without splitter plates of different thicknesses. Results regarding the starting cycle for outer streams only, the fully established supersonic flow, and the base pressure between the center jet and outer streams are provided.

Memorandum presenting a determination of the shapes of bodies with minimum pressure drag for a given lift at high supersonic speeds and satisfying conditions of given length and width with the aid of Newton's law of resistance. The resulting shapes have flat bottoms which are also rectangular. To determine if the bodies do actually have improved lift-drag ratios at high supersonic speeds, several wedges satisfying numerically different sets of given conditions were tested at Mach number 5.

Effective flame speeds of free turbulent flames were measured by photographic, ionization-gap, and photomultiplier-tube methods, and were found to have a statistical distribution attributed to the nature of the turbulent field. The effective turbulent flame speeds for the free flame were less than those previously measured for flames stabilized on nozzle burners, Bunsen burners, and bluff bodies. The statistical spread of the effective turbulent flame speeds was markedly wider in the lean and rich fuel-air-ratio regions, which might be attributed to the greater sensitivity of laminar flame speed to flame temperature in those regions. Values calculated from the turbulent free-flame-speed analysis proposed by Tucker apparently form upper limits for the statistical spread of free-flame-speed data. Hot-wire anemometer measurements of the longitudinal velocity fluctuation intensity and longitudinal correlation coefficient were made and were employed in the comparison of data and in the theoretical calculation of turbulent flame speed.

This paper presents the results of an induced angle-of-attack calculation using a method applicable to a propeller with arbitrary circulation distribution. Tables of induced angles of attack and section angles of attack and curves of wake-survey results are presented for the NACA 10-(3)(066)-03, 10-(3)(049)-03, 10-(3)(090)-03, 10-(5)(066)-03, and 10-(0)(066)-03 propellers. A brief description of the method of calculating propeller induced angles of attack is given.

Report presenting a test-stand investigation conducted on a rectangular ramjet engine design for installation in an aircraft wing. The engine operated without excessive engine noise or vibration over the entire range of operating conditions. Results regarding inlet velocity, exhaust flame characteristics, fuel-air ratio, and total-temperature rise are provided.

A family of related airfoils having the position of maximum camber unusually far forward was investigated in the variable-density tunnel as an extension of the study recently completed of a large number of related airfoils. The new airfoils gave improved characteristics over those previously investigated, especially in regard to the pitching moment. Some of the new sections are markedly superior to well-known and commonly used sections and should replace them in applications requiring a slightly cambered section of moderate thickness having a small pitching-moment coefficient.

The laws of comparison of dynamically similar fluid motions are derived by three different methods based on the same principle and yielding the same or equivalent formulas. This report outlines the three current methods of comparing dynamically similar motions, more especially of fluids, initiated respectively by Newton, Stokes (or Helmholtz), and Rayleigh. These three methods, viz., the integral, the differential, and the dimensional, are enough alike to be studied profitably together. They are treated in succession then compared. (author).

"The rate of change in power of aircraft engines with altitude has been the subject of considerable discussion. Only a small amount of data from direct measurements of the power delivered by airplane engines during flight, however, has been published. This report presents the results of direct measurements of the power delivered by a Liberty 12 airplane engine taken with a hub dynamometer at standard altitudes from zero to 13,000 feet. Six flights were made with the engine installed in a modified DH-4 airplane" (p. 323).

Report presenting the results of an investigation at supersonic speeds to determine the aerodynamic characteristics of a model of the North American MX-770 missile at several designated Mach numbers. No analysis is provided. Information about the longitudinal aerodynamic characteristics with trimmer and elevon deflected and lateral aerodynamic characteristics are described.