Memorandum presenting an investigation of the performance of inlet configurations with a forebody designed for isentropic external compression at a nominal Mach number of 5.6. At zero angle of attack, all the configurations yielded larger total-pressure recoveries than had previously been obtained with a single-conical-shock inlet. Results regarding the flow about the forebody, inlet performance, and performance comparisons are provided.

Note presenting a description of basic electrical networks that compensate for the thermal time lag of thermocouple and resistance thermometer elements used in combustion research and in the control of jet power plants. The measurement or the detection of rapid temperature changes by use of such elements can thereby be improved.

"A wind-tunnel investigation was made to determine the effects on the aerodynamic characteristics of a 35 degree swept-wing airplane of applying area-suction boundary-layer control to the trailing-edge flaps. Flight tests of a similar airplane were then conducted to determine the effect of boundary-layer control in the handling qualities and operation of the airplane, particularly during landing. The wind-tunnel and flight tests indicated that area suction applied to the trailing-edge flaps produced significant increases in flap lift increment" (p. 1).

"An investigation was conducted in the Ames 12-foot pressure wind tunnel to determine the effect of an operating propeller on the aerodynamic characteristics of a 1/19-scale model of the Lockheed XFV-1 airplane. Several full-scale power conditions were simulated at Mach numbers from 0.50 to 0.92; the.Reynolds number was constant at 1.7 million. Lift, longitudinal force, pitch, roll, and yaw characteristics, determined with and without power, are presented for the complete model and for various combinations of model components" (p. 1).

From Introduction: "The results of this complete evaluation of the altitude performance and operational characteristics of the two types of flame-holder and fuel-system configurations are reported herein.The starting limits of both configurations at a flight Mach number of 0.6 are also discussed."

An investigation to determine the heat-shock resistant properties of two molybdenum disilicide turbine blades under centrifugal loads imposed by turbine rotation is presented. Molybdenum disilicide turbine blades fabricated by hot-pressing techniques withstood heat-shock conditions under blade centrifugal stresses up to 5350 pounds per square inch. Additional development is required before the heat-shock resistant properties of molybdenum disilicide are satisfactory for turbine-blade application.

Report presenting the aerodynamic characteristics of several wing-fuselage combinations measured at a Mach number of 0.25. Each combination consisted of a triangular wing with an aspect ratio of 2.0 and body of revolution with a fineness ratio of 12.5. Results regarding wings in the presence of bodies, wing-body combinations, and dorsal fins are provided.

Report presenting an investigation in the high-speed tunnel to determine the effects on the chordwise pressure distributions of deflecting a flap-type aileron on a swept wing. The semispan 35 degree sweptback wing had an NACA 65A006 airfoil section, an aspect ratio of 4, and a taper ratio of 0.6.

Report discussing an investigation to determine the effect of wing leading-edge chord-extensions and drooped leading-edge flaps on the spin and spin-recovery characteristics of models of two swept-wing fighter airplanes. The investigation included chord-extensions in the plane of the wing and chord-extensions deflected in combination with drooped leading-edge flaps. The chord extensions were not found to have an appreciable effect on spin or spin-recovery characteristics when installed in the plane of the wing.

Report presenting an investigation in the transonic tunnel on a submerged inlet with a divergent-walled approach ramp to determine flow phenomena, pressure recovery, and external forces to provide correlation with available data obtained on similar inlets. Results regarding the pressure characteristics, aerodynamic forces, and performance comparisons are provided.

Memorandum presenting an investigation of the performance of inlet configurations with a forebody designed for isentropic external compression at a nominal Mach number of 5.6. At zero angle of attack, all of the configurations yielded larger total-pressure recoveries than had previously been obtianed with a single-conical-shock inlet. Results regarding the flow about the forebody and performance comparisons are provided.

Report presenting the effect of channel geometry on flame quenching, as calculated on the basis of average active particle chain lengths, is related among six different geometries: plane parallel plates of infinite extent, cylindrical tubes, rectangular slots, cylindrical annuli, and tubes of elliptical and equilaterally triangular shape. The results indicated that the observed variation of flame quenching as a function of quenching geometry may be successfully predicted for a range of pressures and for rich as well as lean propane-air flames.

Report describing a supersonic-compressor rotor designed as an impulse-type with some deceleration along the tip and with turning to the axial direction. Results regarding the overall performance, inlet flow distribution, results of rotor-outlet surveys, blade element performance at 90 percent design speed, and blade element performance at open throttle are provided.

Pressure distributions for a series of four boattailed bodies of revolution were obtained and compared with theory for a Mach number of 3.12, a Reynolds number range of 2 x 10 to 6th power to 14 x 10 to the 6th power, and angles of attack from zero to 9 degrees. Second-order theory adequately predicted the pressure distribution for regions free of the effects of cross-flow separation.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Will Wilson, regarding a legal question submitted for clarification: Whether Comptroller of Public Accounts has the power to invoke against the taxpayer the $25 penalty provided in Section 12 of Article 7047 1-1, VCS (providing an excise tax on the sale of radio and television sets) and require its payment under the bond without a court judgment.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Will Wilson, regarding a legal question submitted for clarification: Constitutionality of House Bill No. 495 and pending committee amendment to said Bill and related questions.

Letter opinion issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, John Ben Shepperd, regarding a legal question submitted for clarification; Authority of the Highway Commission to apportion voluntarily tendered registration fees, unlawfully collected to the proper counties.

Letter opinion issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, John Ben Shepperd, regarding a legal question submitted for clarification; The eligibility of a man who was discharged from the service prior to December 7, 1941, to be designated Veteran's County Service Officer.

Letter opinion issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, John Ben Shepperd, regarding a legal question submitted for clarification; Status of balances in funds derived from sale of sub-experiment station lands.

Letter opinion issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, John Ben Shepperd, regarding a legal question submitted for clarification; Constitutionality of Senate Bill 24, 54th Legislature, authorizing additional court costs in divorce cases in certain counties.

None

The intercycle evaporators in the Chemical Processing Plant are controlled by density-measuring instruments. Because of difficulties in controlling these evaporators in a satisfactory manner, a series of investigations was begun to measure the boiling points at the elevation of the CPP, and densities near boiling temperatures of a number of solutions in the uranyl nitrate-nitric acid-water system. From these data it was hoped to evaluate temperature sensitve devices as controllers for the evaporators.

Detailed descriptions are given concerning the reactor design, operation, location, and the using agency. Potential hazards are evaluated along with safeguards. A supplement is included which further describes the reactor core. (J.R.D.)

Abstract: "The niobium-carbon system has been determined by X-ray and metallographic examination of sintered and arc-cast alloys. Two carbides exist: hexagonal Nb2C with a limited range of homogeneity, and cubic NbC with a solubility range from 8.25 to 10.25 weight per cent carbon. Dilute alloys freeze by eutectic reaction at 2230 C. The solubility of carbon in niobium is 0.80 at the eutectic temperature, but this decreases rapidly with temperature. Metallographic evidence indicates a peritectic reaction between melt, Nb2C, and NbC; alloys richer in carbon than NbC freeze by eutectic reaction."