Report presenting the effect of channel geometry on flame quenching, as calculated on the basis of average active particle chain lengths, is related among six different geometries: plane parallel plates of infinite extent, cylindrical tubes, rectangular slots, cylindrical annuli, and tubes of elliptical and equilaterally triangular shape. The results indicated that the observed variation of flame quenching as a function of quenching geometry may be successfully predicted for a range of pressures and for rich as well as lean propane-air flames.

Memorandum presenting an investigation of the performance of inlet configurations with a forebody designed for isentropic external compression at a nominal Mach number of 5.6. At zero angle of attack, all the configurations yielded larger total-pressure recoveries than had previously been obtained with a single-conical-shock inlet. Results regarding the flow about the forebody, inlet performance, and performance comparisons are provided.

Memorandum presenting an investigation of the performance of inlet configurations with a forebody designed for isentropic external compression at a nominal Mach number of 5.6. At zero angle of attack, all of the configurations yielded larger total-pressure recoveries than had previously been obtianed with a single-conical-shock inlet. Results regarding the flow about the forebody and performance comparisons are provided.

Report presenting an investigation in the transonic tunnel on a submerged inlet with a divergent-walled approach ramp to determine flow phenomena, pressure recovery, and external forces to provide correlation with available data obtained on similar inlets. Results regarding the pressure characteristics, aerodynamic forces, and performance comparisons are provided.

Report presenting testing of six flutter wings, two swept 45 degrees and four unswept, attached to three freely falling bodies. Flutter frequency and phasing were recorded.

"A wind-tunnel investigation was made to determine the effects on the aerodynamic characteristics of a 35 degree swept-wing airplane of applying area-suction boundary-layer control to the trailing-edge flaps. Flight tests of a similar airplane were then conducted to determine the effect of boundary-layer control in the handling qualities and operation of the airplane, particularly during landing. The wind-tunnel and flight tests indicated that area suction applied to the trailing-edge flaps produced significant increases in flap lift increment" (p. 1).

"At the request of the Air Material Command, Army Air Forces, an investigation was conducted by the NACA Cleveland laboratory to determine the performance characteristics of the compressor of the XJ-41-V turbojet engine. This report is the second in a series presenting the compressor performance and analysis of flow conditions in the compressor. The static-pressure variation in the direction of flow through the compressor and the location and the cause of the maximum flow restriction at an equivalent speed of 8000 rpm are presented" (p. 1).

This report describes a series of tests made on a 1/40-scale model of the U. S. Airship "Akron" (ZRS-4) for the purpose of determining the drag, lift, and pitching moments of the bare hull and of the hull equipped with two different sets of fins. Measurements were also made of the elevator forces and hinge moments.

Report presenting an investigation in the high-speed tunnel to determine the effects on the chordwise pressure distributions of deflecting a flap-type aileron on a swept wing. The semispan 35 degree sweptback wing had an NACA 65A006 airfoil section, an aspect ratio of 4, and a taper ratio of 0.6.

Report presenting the aerodynamic characteristics of several wing-fuselage combinations measured at a Mach number of 0.25. Each combination consisted of a triangular wing with an aspect ratio of 2.0 and body of revolution with a fineness ratio of 12.5. Results regarding wings in the presence of bodies, wing-body combinations, and dorsal fins are provided.

"Pressure-distribution data of the NACA 64(sub 1)-012 and 64(sub 1)A012 airfoils have been analyzed to determine the effects of increasing the trailing-edge angle from 9 to 14 degrees. The primary effect of increasing the trailing-edge angle was to decrease the loading over the rear portion of the airfoil under lifting conditions. The differences in trailing-edge load increased with Mach number and lift coefficient" (p. 1).

From Introduction: "The results of this complete evaluation of the altitude performance and operational characteristics of the two types of flame-holder and fuel-system configurations are reported herein.The starting limits of both configurations at a flight Mach number of 0.6 are also discussed."

"It is shown that for velocities slightly in excess of sonic, the position of detached shock wave located in front of a given body at zero angle of attack may be estimated theoretically to a reasonable degree of accuracy. In case of bodies of revolution the result was simple, but for two-dimensional bodies, pressure coefficient varies with Mach number, and slight difficulty appears. Theory developed compares favorably with available experimental data" (p. 1).

From Summary: "Tests of a 1/7 size model of the Grumman XJR2F-1 amphibian were made in Langley tank no.1 to examine the landing behavior in rough water and to measure the normal and angular accelerations experienced by the model during these landings. All landings were made normal to the direction of wave advance, a condition assumed to produce the greatest accelerations. Wave heights of 4.4 and 8.0 inches (2.5 and 4.7 ft, full size) were used in the tests and the wave lengths were varied between 10 and 50 feet (70 and 350 ft, full size)."

An investigation to determine the heat-shock resistant properties of two molybdenum disilicide turbine blades under centrifugal loads imposed by turbine rotation is presented. Molybdenum disilicide turbine blades fabricated by hot-pressing techniques withstood heat-shock conditions under blade centrifugal stresses up to 5350 pounds per square inch. Additional development is required before the heat-shock resistant properties of molybdenum disilicide are satisfactory for turbine-blade application.

Testing was performed at Mach number 1.53 with a wing-fuselage combination with a wing with 63 degrees leading-edge sweep, an aspect ratio of 3.46, and a taper ratio of 0.25. The wing had an NACA 64A005 thickness distribution parallel to the plane of symmetry and was cambered and twisted. Results regarding the comparison of lift, drag, and pitching-moment characteristics of WF-63c and WF-63, effects of sweep, and effects of Reynolds number are provided.

From Summary: "Wind-tunnel tests of a full-scale two-blade NACA 10-(10)(08)-03 (high camber) propeller have been made for a range of blade angles from 20 degrees to 55 degrees at airspeeds up to 500 miles per hour. The results of these tests have been compared with results from previous tests of the NACA 10-(3) (08)-03 (low camber) and NACA 10-(5)(08)-03 (medium camber) propellers to evaluate the effects of blade-section camber on propeller aerodynamic characteristics."

Pressure distributions for a series of four boattailed bodies of revolution were obtained and compared with theory for a Mach number of 3.12, a Reynolds number range of 2 x 10 to 6th power to 14 x 10 to the 6th power, and angles of attack from zero to 9 degrees. Second-order theory adequately predicted the pressure distribution for regions free of the effects of cross-flow separation.

"A Douglas C-74 airplane, during a test dive at about 0.525 Mach number, experienced uncontrollable longitudinal oscillations sufficient to cause shedding of the outer wing panels and the subsequent crash of the airplane. Tests of a section of the horizontal tail plane from a C-74 airplane were conducted in the Ames 16-foot high-speed wind tunnel to investigate the possibility of the tail as a contributing factor to the accident. The results of the investigations of fabric-covered elevators in various conditions of surface deformation are presented in this report" (p. 1).

Note presenting a description of basic electrical networks that compensate for the thermal time lag of thermocouple and resistance thermometer elements used in combustion research and in the control of jet power plants. The measurement or the detection of rapid temperature changes by use of such elements can thereby be improved.

"An analysis has been made of the lift control effectiveness of a 20-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section from section lift-coefficient data obtained at Mach numbers from 0.3 to 0.875. In addition, the effectiveness of the plain flap as a lift-control device has been compared with the corresponding effectiveness of both a spoiler and a dive-recovery flap on the NACA 65-210 airfoil section. The analysis indicates that the plain trailing-edge flap employed on the 10-percent-thick airfoil at Mach numbers as high as 0.875 retains at least 50-percent of its low-speed lift-control effectiveness, and is sufficiently effective in lateral control application, assuming a rigid wing, to provide adequate airplane rolling characteristics" (p. 1).

"An analysis has been made of the lift-control effectiveness of a 20-percent-chord plain trailing-edge flap on the NACA 65-210 airfoil section from section lift-coefficient data obtained at Mach numbers from 0.3 to 0.875. In addition, the effectiveness of the plain flap as a lift-control device has been compared with the corresponding effectiveness of both a spoiler and a dive-recovery flag on the INCA 65-210 airfoil section" (p. 1).

"An investigation was conducted in the Ames 12-foot pressure wind tunnel to determine the effect of an operating propeller on the aerodynamic characteristics of a 1/19-scale model of the Lockheed XFV-1 airplane. Several full-scale power conditions were simulated at Mach numbers from 0.50 to 0.92; the.Reynolds number was constant at 1.7 million. Lift, longitudinal force, pitch, roll, and yaw characteristics, determined with and without power, are presented for the complete model and for various combinations of model components" (p. 1).

Report describing a supersonic-compressor rotor designed as an impulse-type with some deceleration along the tip and with turning to the axial direction. Results regarding the overall performance, inlet flow distribution, results of rotor-outlet surveys, blade element performance at 90 percent design speed, and blade element performance at open throttle are provided.