Aspects of an inertial-confinement, fusion reactor that uses an energy release {approx gt}10{sup 11} joules are discussed. The large energy release makes possible direct conversion of the fusion neutrons' energy after nuclear heating of an evaporated blanket to the plasma state. Surface damage by charged particles is avoided and structural damage by neutrons is alleviated. Complex fuel assemblies and other expandable parts may be used as a result of the high monetary value of the energy release.

A high-intensity subkilovolt x-ray calibration source utilizing proton-induced inner-shell atomic fluorescence of low-Z elements is described. The high photon yields and low bremsstrahlung background associated with this phenomenon are ideally suited to provide intense, nearly monoenergetic x-ray beams. The proton accelerator is a 3 mA, 300 kV Cockroft-Walton using a conventional rf hydrogen ion source. Seven remotely-selectable targets capable of heat dissipation of 5 kW/cm/sup 2/ are used to provide characteristic x-rays with energies between 100 and 1000 eV. Source strengths are of the order of 10/sup 13/ to 10/sup 14/ photons/sec. Methods of reducing spectral contamination due to hydrocarbon build-up on the target are discussed. Typical x-ray spectra (Cu-L, C-K and B-K) are shown.

Several experimental routes can be used to develop a better understanding of the polymeric constitution (polyanionic and/or polyhedral distribution) of borate, germanate, and silicate glasses. Spectral, chemical, physical-chemical, and mechanical property information can be determined directly for the glass compositions of interest. Generally, only physical-chemical information is readily accessible for the corresponding high temperature liquids. It will be shown that information on each state of matter has its own particular merits. Most of the evidence thus far published suggests an excellent agreement between polyhedral distributions in an oxide glass and its corresponding high temperature liquid state. There is no well known oxide glass forming system for which such a state of affairs does not exist. In spite of this, occasional efforts are put forth which ignore some of what is known for oxide liquids, glasses, and crystals. Such attempts therefore invariably imply, if only indirectly, that significant changes occur in the polyhedral distributions close to the glass transition temperature region. Specific examples to be discussed will include efforts that avoid well known coordination change equilibria such as BO/sub 3/ reversible BO/sub 4/ and GeO/sub 4/ reversible GeO/sub 6/.

RELAP4 is a computer code which can be used for the transient therm~l hydraulic analysis of light water reactors and related systems .. Various versions of the RELAP4 code are widely used throughout the world for experimental system analysis, reactor design,and nuclear system safety studies. RELAP4/MOD6 includes many new analytical models which were developed primarily for the analysis of the reflood phase of a PWR loss-of-coolant accident (LOCA) transient. The key feature forming the basis for the MOD6 reflood calculation is a unique moving finite differenced heat conductor. This paper will describe the development and application of the moving heat conductor mesh for use in reflood analysis.

The methods to be employed to form and control plasma potentials in the TMX Upgrade tandem mirror with thermal barriers are described. ECRH-generated mirror -confined electron plasmas are used to establish a negative potential region to isolate the end-plug and central-cell celectrons. This thermal isolation will allow a higher end-plug electron temperature and an increased central-cell confining potential. Improved axial central-cell ion confinement results since higher temperature central-cell ions can be confined. This paper describes: (1) calculations of the sensitivity of barrier formation to vacuum conditions and to the presence of impurities in the neutral beams, (2) calculations of microwave penetration and absorption used to design the ECRH system, and (3) techniques to limit electron runaway to high energies by localized microwave beams and by relativistic detuning.

Extensive tidal studies in island wells and the lagoon at Enewetak Atoll have shown that island ground water dynamics are controlled by a layered aquifer system. The surface aquifer of unconsolidated Holocene material extends to a depth of approximately 15 m, and has a hydraulic conductivity K = 60 m/day. From 15 to 60 m (approximate lagoon depth) the reef structure consists of successive layers of altered Pleistocene materials, with bulk permeability substantially higher than that of the surface aquifer. Because of wave set-up over the windward reef and the limited pass area for outflow at the south end of the atoll, lagoon tides rise in phase with the ocean tides but fall later than the ocean water level. This results in a net lagoon-to-ocean head which can act as the driving force for outflow through the permeable Pleistocene aquifer. This model suggests that fresh water, nutrients or radioactive contaminants found in island ground water or reef interstitial water may be discharged primarily into the ocean rather than the lagoon. Atoll island fresh water resources are controlled by recharge, seawater dilution due to vertical tidal mixing between the surface and deeper aquifers, and by loss due to entrainment by the …

The Workshop on Core and Sample Curation was held to discuss the best means of handling, distributing, and advertising samples and data collected during a Continental Scientific Drilling Program (CSDP) and to establish better communication between sample curators regarding common problems. It was geneerally agreed that CSDP samples should be handled, on a regional basis, by existing data systems and sample repositories judged to have adequate staff and support. Repository design, sample handling procedures, and sample accounting systems were discussed. Across North America, support for curation of geological samples was varied, but it was strongest within states or regions with well-established energy and mineral industries. A well-supported repository pays for itself through the circulation and preservation of samples and stratigraphic information. A national CSDP must have a well-established curatorial policy and system of regional repositories to circulate information and samples throughout the scientific community. Well-curated samples and data are a national resource with considerable benefits for industry and academia. Attendees agreed to form a Society of Geoscience Curators to maintain communication between curators from private, government, and university repositories and core research laboratories.

Bunched beams of 100 and 150 GeV have been stored in the Fermilab Main Ring for periods of up to one hour. The observations of beam current and beam profiles are analyzed for the effects of gas scattering, chromaticity and non-linear magnetic field.

Diagrams and slide reproductions of the system are presented; and performance, maintenance, and cost information is outlined. (WHK)

None

VISAR (Velocity Interferometer System for Any Reflector) is commonly used for measuring flyer-plate velocities up to 6 km/s. Flyer plates can travel as much as 1 mm, which is large compared to usual depth-of-focus requirements for VISARs. Flyer plates are explosively driven, or driven by some other very energetic means; as such, they must be tested in a chamber, which will contain the explosion. Routing the laser beam to the chamber and the signal beam to the VISAR can be done safely and easily in multi-mode optical fibers. We have optimized a fiber-coupled VISAR system for measuring flyer-plate velocities. This system given constant signal levels over the full travel of the flyer plate. Furthermore, the signal-collection efficiency is maximized, which allows use of a moderately sized laser. We also have optimized the VISAR cavity so it does not limit the system efficiency while giving a velocity sensitivity of about 1 km/s per fringe. 5 refs.

The ZGS people went off in every direction: to universities, to other laboratories, to universities and laboratories in other countries, and to other occupations in the private sector or federal agencies. Some people even cycled around through one or more of the above and eventually would up back to Argonne. As a good pupil of the David Manson school of weasel words. I recognize the need to insert a {open_quotes}to the best of my knowledge{close_quotes} disclaimer statement here. It became clear to me that I couldn`t vouch for the accuracy of all of the information shown below when, to my surprise and delight, I found on the official registration list for this conference the names of people I really, really, never expected to see again!

In our light ion inertial confinement fusion (ICF) program, fusion capsules are driven with an intense x-ray radiation field produced when an intense beam of ions penetrates a radiation case and deposits energy in a foam x-ray conversion region. A first step in the program is to generate and measure these intense fields on the Particle Beam Fusion Accelerator II (PBFA II). Our goal is to generate a 100-eV radiation temperature in lithium ion beam driven hohlraums, the radiation environment which will provide the initial drive temperature for ion beam driven implosion systems designed to achieve high gain. In this paper, we describe the design of such hohlraum targets and their predicted performance on PBFA II as we provide increasing ion beam intensities.

Radiography techniques utilizing large area x-ray sources (typically {<=} 7 keV) and pinhole-imaging gated x-ray diagnostics have long been used at the Nova laser facility. However, for targets requiring higher energy x-ray backlighters (> 9 keV), low conversion efficiencies and pinhole losses combine to make this scheme unworkable. The technique of point projection radiography has been improved upon to make imaging at high x-ray energies feasible. In this scheme a {open_quotes}point{close_quotes} source of x-rays, usually a small diameter ({<=}25 {mu}m) fiber, is illuminated with a single, 100 ps pulse from the Nova laser. A gated x-ray imager with a 500 ps electronic gate width is used to record the projected image. The experimental challenges this technique presents and experimental results will be discussed.

Both the efficiency of an implosion and the growth rate of hydrodynamic instability increase with the aspect ratio of an implosion. In order to study the physics of implosions with high Rayleigh-Taylor growth factors, we use doped ablators which should minimize x-ray preheat and shell decompression, and hence increase in-flight aspect ratio. We use x-ray backlighting techniques to image the indirectly-driven capsules. We record backlit 4.7 keV images of the full capsule throughout the implosion phase with 55 ps and 15 {mu}m resolution. We use these images to measure the in-flight aspect ratios for doped ablators, and we inferred the radial density profile as a function of time by Abel inverting the x-ray transmission profiles.

For direct drive ICF, a capsule is imploded by directly illuminating the surface with laser light. Beam smoothing and uniformity of illumination affect the seeding of instabilities at the ablation front. We have developed a technique for studying the imprint of a laser beam on a thin foil using an x-ray laser as an XUV backlighter. We use multilayer XUV optics to relay the x-ray laser onto the directly driven foil, and then to image the foil modulation onto a CCD camera. This technique allows us to measure small fractional variations in the foil thickness. We have measured the modulation due to imprint from a low intensity 0.35 pm drive beam incident on a 3 {mu}m Si foil using an yttrium x-ray laser on Nova. We present results from a similar technique to measure the imprinted modulation due to a low intensity 0.53 {mu}m drive beam incident on a 2 {mu}m Al foil using a germanium x-ray laser at the Vulcan facility.

This document is intended to provide additional information supplementing a prior publication. The discussion describes the details of the implementation of the proton nonelastic cross section parameterization for LAHET usage. It also documents extensions of the method to stable nuclei with 2 {le} Z {le} 5.

Sensor arrays offer opportunities to beam form, and time-frequency analyses offer additional insights to the wavefield data. Data collected while monitoring three different sources with unattended ground sensors in a 16-element, small-aperture (approximately 5 meters) geophone array are used as examples of model-based seismic signal processing on actual geophone array data. The three sources monitored were: (Source 01). A frequency-modulated chirp of an electromechanical shaker mounted on the floor of an underground bunker. Three 60-second time-windows corresponding to (a) 50 Hz to 55 Hz sweep, (b) 60 Hz to 70 Hz sweep, and (c) 80 Hz to 90 Hz sweep. (Source 02). A single transient impact of a hammer striking the floor of the bunker. Twenty seconds of data (with the transient event approximately mid-point in the time window.(Source 11)). The transient event of a diesel generator turning on, including a few seconds before the turn-on time and a few seconds after the generator reaches steady-state conditions. The high-frequency seismic array was positioned at the surface of the ground at a distance of 150 meters (North) of the underground bunker. Four Y-shaped subarrays (each with 2-meter apertures) in a Y-shaped pattern (with a 6-meter aperture) using a total of 16 …

There is an ongoing effort to develop accelerating modules for high-current electron accelerators for advanced radiography application. Accelerating modules with low beam-cavity coupling impedances along with gap designs with acceptable field stresses comprise a set of fundamental design criteria. We examine improved cell designs which have been developed for accelerator application in several radiographic operating regimes. We evaluate interaction impedances, analyze the effects of beam structure coupling on beam dynamics (beam break-up instability and corkscrew motion). We also provide estimates of coupling through interesting new high-gradient insulators and evaluate their potential future application in induction cells.

The value of energy technology R and D as an insurance investment to reduce the cost of climate change stabilization, oil price shocks, urban air pollution, and energy disruptions is estimated to be $5-8 billion/year in sum total. However, the total that is justified is actually less than this sum because some R and D is applicable to more than one risk. nevertheless, the total DOE investment in energy technology R and D (about $1.3 billion/year in FY97) seems easily justified by its insurance value alone; and, in fact, more might be warranted, particularly in the areas related to climate change and urban air pollution. This conclusion appears robust even if the private sector is assumed to be investing a comparable amount. Not counted is the value to the economy and to US competitiveness of better energy technologies that may result from the R and D; only the insurance value for reducing the cost of these four risks to society was estimated.

False positive detections account for a great part of the expense associated with unexploded ordnance (UXO) remediation. Presently fielded systems like pulsed electromagnetic induction systems and cesium-vapor magnetometers are able to distinguish between UXO and other metallic ground clutter only with difficulty. The discovery of giant magnetoresistance (GMR) has led to the development of a new generation of integrated-circuit magnetic sensors that are far more sensitive than previously available room-temperature-operation electronic devices. The small size of GMR sensors makes possible the construction of array detectors that can be used to image the flux emanating from a ferrous object or from a non-ferrous object with eddy currents imposed by an external coil. The purpose of a GMR-based imaging detector would be to allow the operator to easily distinguish between UXO and benign objects (like shrapnel or spent bullets) that litter formerly used defense sites (FUDS). In order to demonstrate the potential of a GMR-based imaging technology, a crude magnetic imaging system has been constructed using commercially available sensors. The ability to roughly determine the outline and disposition of magnetic objects has been demonstrated. Improvements to the system which are necessary to make it into a high-performance UXO detector are outlined.

An MPI library's implementation of broadcast communication can significantly affect the performance of applications built with that library. In order to choose between similar implementations or to evaluate available libraries, accurate measurements of broadcast performance are required. As we demonstrate, existing methods for measuring broadcast performance are either inaccurate or inadequate. Fortunately, we have designed an accurate method for measuring broadcast performance, even in a challenging grid environment. Measuring broadcast performance is not easy. Simply sending one broadcast after another allows them to proceed through the network concurrently, thus resulting in inaccurate per broadcast timings. Existing methods either fail to eliminate this pipelining effect or eliminate it by introducing overheads that are as difficult to measure as the performance of the broadcast itself. This problem becomes even more challenging in grid environments. Latencies a long different links can vary significantly. Thus, an algorithm's performance is difficult to predict from it's communication pattern. Even when accurate pre-diction is possible, the pattern is often unknown. Our method introduces a measurable overhead to eliminate the pipelining effect, regardless of variations in link latencies. choose between different available implementations. Also, accurate and complete measurements could guide use of a given implementation to improve application …

Beam tests of the ANL 12 MHz Radio-Frequency Quadruple (RFQ), designed for use as the initial element of an injector system for radioactive beams into the existing ATLAS accelerators, are in progress. Recent high-voltage tests of the RFQ without beam achieved the design intervane voltage of 100 kV CW, enabling beam tests with A/q as large as 132 using beams from the ANL Physics Division 4 MV Dynamitron accelerator facility. Although the RFQ was designed for bunched beams, initial tests have been performed with unbunched beams. Experiments with stable, unbunched beams of singly-charged {sup 132}Xe and {sup 84}Kr measured the output beam energy distribution as a function of the RFQ operating voltage. The observed energies are in excellent agreement with numerical beam simulations.

A glass-bonded sodalite ceramic waste form is being developed for the long-term immobilization of salt wastes that are generated during spent nuclear fuel conditioning activities. A durable waste form is prepared by hot isostatic pressing (HIP) a mixture of salt-loaded zeolite powders and glass frit. A mechanistic description of the corrosion processes is being developed to support qualification of the CWF for disposal. The initial set of characterization tests included two standard tests that have been used extensively to study the corrosion behavior of high level waste (HLW) glasses: the Material Characterization Center-1 (MCC-1) Test and the Product Consistency Test (PCT). Direct comparison of the results of tests with the reference CWF and HLW glasses indicate that the corrosion behaviors of the CWF and HLW glasses are very similar.