A method of calculating the horizontal tail area for an airplane equipped with flaps is presented. The general problem of tail design, the effects of flaps on the factors involved, and the manner in which the flaps change the requirements upon which the minimum horizontal tail area is based are discussed.

Aerodynamic force tests of a Clark Y wing equipped with "Maxwell" type leading-edge slots were conducted in the N.A.C.A. 7- by 10-foot tunnel to ascertain the aerodynamic characteristics, which involved the determination of the best slot-gap opening, the effects of slat width, and the effect of a trailing-edge flap. The Maxwell wing with a wide-chord slat (0.30 c(sub w)) and with a 0.211 c(sub w) split flap deflected 60 degrees had a C(sub L sub max) of 2.53 or about twice that of the plain wing. The wing with the wide slat also had, in general, improved aerodynamic characteristics over those of the Maxwell wing with slat, and had about the same aerodynamic characteristics as a Handley Page slotted wing with approximately the same size of slat.

In this report charts are given showing the relation between time, velocities, and altitude for airplanes having various terminal velocities diving in a standard atmosphere. The range of starting altitudes is from 8,000 to 32,000 feet, and the terminal velocities vary from 150 to 550 miles per hour. A comparison is made between an experimental case and the results obtained from the charts. Examples pointing out the use of the charts are included.

The present report contains the description and typical application of two photoelastic methods which are suitable for the study of stress and strain conditions in three dimensions, namely: the fixation method and the immersion method.

Based on the universal laws of turbulent velocity distribution at rough and smooth walls, there is in the present work presented a method that allows surface roughness tests and in particular, measurements on the roughness of ship surfaces to be carried out in a much simpler manner. The types of roughness investigated were in the form of flat, rough plates installed in a square-section rectangular channel, the other three walls always being smooth. Twenty-one plates of various roughness were investigated, the roughness elements being the following: spheres of diameter 0.41 and 0.21, respectively, spherical segments, cones, and "short" and "long" angles.

A need has arisen for a new determination of the velocity profiles in the boundary layer. Assuming that the character of the velocity distribution depends to a large extent on the character of the shear distribution across the boundary layer, we shall consider the nature of the shear distribution for a boundary layer with a pressure gradient.

Report discusses the important principles involved in the operation of a baffle for an engine cylinder and how using a correctly designed baffle can improve cooling. The baffle-exit radius and width and exit-duct length were found to be the most important parts of the baffle and a baffle that gave a relatively uniform temperature distribution was designed.

The effects of the geometrical arrangement of tricycle landing gears on various characteristics of an airplane equipped with such landing gear is discussed. The characteristics discussed include directional stability, overturning tendencies, steering and ground handling, shimmy, takeoff, and porpoising. The conclusions are summarized in a table.

Circular describing the Hafner A.R.III gyroplane, which is a single-seater with a Pobjoy Niagara III engine. Details of the rotor blades, controls, rotor, and climbing properties are provided.

"An analysis of the principal results of recent NACA lateral control research is made by utilizing the experience and progress gained during the course of the investigation. Two things are considered of primary importance in judging the effectiveness of different control devices: the (calculated) banking and yawing motion of a typical small airplane caused by a deflection of the control, and the stick force required to produce this deflection. The report includes a table in which a number of different lateral control devices are compared on these bases" (p. 1).

Report presents the results of tests of a 1/10-scale model of the XN2Y-1 airplane tested in the NACA 5-foot vertical wind tunnel in which the six components of forces and moments were measured. The model was tested in 17 attitudes in which the full-scale airplane had been observed to spin, in order to determine the effects of scale, tunnel, and interference. In addition, a series of tests was made to cover the range of angles of attack, angles of sideslip, rates of rotation, and control setting likely to be encountered by a spinning airplane. The data were used to estimate the probable attitudes in steady spins of an airplane in flight and of a model in the free-spinning tunnel. The estimated attitudes of steady spin were compared with attitudes measured in flight and in the spinning tunnel. The results indicate that corrections for certain scale and tunnel effects are necessary to estimate full-scale spinning attitudes from model results.

Report presents an analysis of the factors that determine the periodic twist of a rotor blade under the action of the air forces on it. The results of the analysis show that the Fourier coefficients of the twist are linear expressions involving only the tip-speed ratio, the pitch setting, the inflow coefficient, the pitching-moment coefficient of the blade airfoil section, and the physical characteristics of the rotor blade and machine.

Report presents the results of pressure-distribution measurements on a 1/40-scale model of the U. S. Airship "Akron" conducted in the NACA 20-foot wind tunnel. The measurements were made on the starboard fin of each of four sets of horizontal tail surfaces, all of approximately the same area but differing in span-chord ratio, for five angles of pitch varying from 11.6 degrees to 34 degrees, for four elevator angles, and at air speeds ranging from 56 to 77 miles per hour. Pressures were also measured at 13 stations along the rear half of the port side of the hull at one elevator setting for the same five angles of pitch and at an air speed of approximately 91 miles per hour. The normal force on the fin and the moment of forces about the fin root were determined. The results indicate that, ignoring the effect on drag, it would be advantageous from structural considerations to use a fin of lower span-chord ratio than that used on the "Akron.".

This report presents the results of pressure-distribution tests of a Clark y wing model with a partial-span split flap made to determine the distribution of air loads over both the wing and the flap. The model was used in conjunction with a reflection plane in the NACA 7 by 10 foot wind tunnel. The 20-percent-chord split flap extended over the inboard 60 percent of the semispan. The tests were made at various flap deflections up to 45 degrees and covered a range of angles of attack from zero lift to approximately maximum lift for each deflection.

Annual report submitted by the Boy Scouts of America to Congress describing highlights from 1936, activities, service reports, honors, finance, organizational leadership, and other information about scouting programs.