Progress in the scientific and practical fields of aviation has caused the Swiss Institute of Technology to organize lectures and practical training courses in all three branches of aeronautics and to found centers of scientific research, laboratories, etc., in order to supply the government and industries with scientifically and technically trained engineers.

Circular presenting a description of the C.A.M.S. 60, which is a twin-engine monoplane with a medium-thickness wing and two floats. Details of the wings, engines, fuselages, floor, rear cabin, floats, and flying qualities are provided.

Report issued by the U.S. Bureau of Mines on the coal mine related deaths that occurred during the month of March, 1931. The number of fatalities and their causes are listed. This report includes tables.

"During an investigation to determine the possibilities and limitations of a two-stroke-cycle engine and ignition, it was necessary to develop a fuel injection valve nozzle to produce a disk-shaped, well dispersed spray. Preliminary tests showed that two smooth jets impinging upon each other at an angle of 74 degrees gave a spray with the desired characteristics. Nozzles were built on this basis and, when used in fuel-injection valves, produced a spray that fulfilled the original requirements" (p. 1).

Discusses the nutritional value and versatility of the egg; provides recipes and suggests ways to use eggs in a variety dishes and sauces.

Describes the damage caused by English sparrows and different methods of controlling them.

This report describes test made in the Variable Density Wind Tunnel of the NACA to determine the possibility of controlling the boundary layer on the upper surface of an airfoil by use of the low pressure existing near the leading edge. The low pressure was used to induce flow through slots in the upper surface of the wing. The tests showed that the angle of attack for maximum lift was increased at the expense of a reduction in the maximum lift coefficient and an increase in the drag coefficient.

This investigation has a double object: 1) the calculation of the general characteristics of certain wings with progressively varying sections; 2) the determination of data furnishing, in certain cases, some information on the actual distribution of the external forces acting on a wing. We shall try to show certain advantages belonging to the few wing types of variable section which we shall study and that, even if the general aerodynamic coefficients of these wings are not often clearly superior to those of certain wings of uniform section, the wings of variable section nevertheless have certain advantages over those of uniform section in the distribution of the attainable stresses.

In connection with the development of a method for analyzing indicator cards taken from high-speed compression-ignition engines, this investigation was undertaken to determine the average quantity of fuel discharged during each crank degree of injection period.

Circular describing the Ateliers des Mureaux 111 R.2 military airplane, which is a long-distance all-metal observation monoplane. A description of the design and construction, characteristics, flying qualities, drawings, and photographs are provided.

Theoretical relations involved in the study are reviewed to furnish a basis upon which experimental data can be properly analyzed. The structure of the atmosphere in relation to the load-factor problem is briefly discussed, and the acceleration data obtained on a number of flights with various airplanes are presented and analyzed to the extent that the results are applicable to n=any airplane.

"A comparison of the relative economy of airplane construction shows that monoplanes are cheaper than biplanes; that all-metal construction is much more expensive than mixed construction; that multi-engine airplanes are more expensive than single-engine types of the same carrying capacity and speed;that the cost of airplanes is materially reduced by increasing their size without increasing the number of engines. The greatest economy usually coincides with the best aerodynamic and static conditions and the cost is always increased by safety requirements" (p. 1).

Circular describing the S.P.C.A. 40 T, which is a commercial all-metal cantilever airplane that was guided by the two essential requirements of economy and safety in its design. Details of the design, power, test results, fuel tanks, characteristics, performances, drawings, and photographs are provided.

"Static tests on paper cylinders were conducted at the Langley Memorial Aeronautical Laboratory at Langley Field, Virginia, to obtain qualitative information in connection with a study of the strength of stressed-skin fuselages. The effects of radius-thickness ratio and bulkhead spacing were investigated with the cylinders in compression, bending, combined bending and shear, and torsion" (p. 1).

"When an airplane describes a curve it takes a certain time for it to turn from level to inclined position and then back to level again. In the following, we express the motion about the horizontal axis as "roll" or "bank" and the motion perpendicular to the vertical axis, i.e., the actual curve, as "turn." Equations and tables provide results on various aspects of turns, control settings, acceleration, inertia moments, and angular velocity" (p. 2).

The object of the present study was to define experimentally the field of temperature and velocity in a heated flat plate when exposed to an air stream whose direction is parallel to it, then calculate therefrom the heat transference and the friction past the flat plate, and lastly, compare the test data with the mathematical theory. To ensure comparable results, we were to actually obtain or else approximate: a) two-dimensional flow; b) constant plate temperature in the direction of the stream. To approximate the flow in two dimensions, we chose a relatively wide plate and measured the velocity and temperature in the median plane.