"Results of measurements are given as a supplement to earlier tests for a laminar profile with nose flap; magnitude, form, and angle of attack of the flap were systematically changed. The experiments were carried out at an effective Reynolds number of 8.2 x 10(exp 5). A comparison with measurements on other profiles shows that the effect of a nose flap is essentially dependent upon magnitude of the nose radius coefficient of the profile" (p. 1).

"When thin-walled columns formed from flanged sheet, such as used in airplane construction, are subjected to axial load, their behavior at failure varies according to the slenderness ratio. On long columns the axis deflects laterally while the cross section form is maintained; buckling results. The respective breaking load in the elastic range is computed by Euler's formula and for the plastic range by the Engesser- Karman formula. Its magnitude is essentially dependent upon the length" (p. 1).

"After a brief survey of the available methods for measuring the temperatures of machine parts at high speed, in particular turbine blades and rotors, an apparatus is described which is constructed on the principle of induction. Transmission of the measuring current by sliding contacts therefore is avoided. Up-to-date experiments show that it is possible to give the apparatus a high degree of sensitivity and accuracy" (p. 1).

The following investigations are connected with experiments on fans carried out by the author in the Gouttingen Aerodynamic Laboratory within the framework of the preliminary experiments for the new Gouttingen wind-tunnel project. A fan rotor was developed which had very high efficiency at the design point corresponding to moderate pressure and which, in addition, could operate at a proportionally high pressure, rise. To establish the determining operating factors the author carried out extensive theoretical investigation in Hannover. In this it was necessary, to depart from the usual assumption of vanishing radial velocities. The calculations were substantially lightened by the introduction of diagrams. The, first part of the.report describes the theoretical investigations; the second, the experiments carried out at Gouttingen.

"In the present paper an investigation is made of two stages of a multistage turboblower having a vaneless diffuser behind the impeller and guide vanes at the inlet to the nest stage. The method employed was that of investigating the performance of the successive elements of the blower (the impeller, vaneless diffuser, ets.) whereby the kinematics of the flow through the blower could be followed and the pressure at the different points computed. The character of the flow and the physical significance of the loss coefficients could thereby be determined so as to secure the best agreement of the computed with the actual performance of the blower" (p. 1).

"The few available test data on the heat dissipation of wholly or partly heated airfoil models are compared with the corresponding data for the flat plate as obtained by an extension of Prandtl's momentum theory, with differentiation between laminar and turbulent boundary layer and transitional region between both, the extent and appearance of which depend upon certain critical factors. The satisfactory agreement obtained justifies far-reaching conclusions in respect to other profile forms and arrangements of heated surface areas. The temperature relationship of the material quantities in its effect on the heat dissipation is discussed as far as is possible at the present state of research, and it is shown that the profile drag of heated wing surfaces can increase or decrease with the temperature increase depending upon the momentarily existent structure of the boundary layer" (p. 1).

"The report presents a method for the computation of axial fan characteristics. The method is based on the assumption that the law of constancy of the circulation along the blade holds, approximately, for all fan conditions for which the blade elements operate at normal angles of attack (up to the stalling angles). Pressure head coefficient K(sub a) and power coefficient K(sub u) for the force components in the axial and tangential directions, respectively, and analogous to the lift and drag coefficients C(sub y) and C(sub x) are conveniently introduced" (p. 1).

"The series of pressure distribution measurements at three test sections on NACA airfoils 2212 and M6 within 170 to 210 angles of attack in reversed flow proved to be largely independent of the profile form. In contradiction to the pressure distribution in normal flow considerable negative pressure from the upper surface spills over onto the lower surface, and vice versa, even in the zone of sound flow. The results are presented as chord-wise pressure and load distribution" (p. 1).

"The concept of the effective ejection velocity of a rocket engine is explained and the magnitude of the attainable ejection velocity theoretically and experimentally investigated. Velocities above 3000 meters per second (6700 mph) are actually measured and the possibilities of further increases shown" (p. 1).

"After a survey of the customary procedures for appraising the profile drag in which pressure drag was discounted and the methods for computing the laminar and turbulent friction flow, the author proposes a method by which the pressure drag can be computed with the aid of the displacement thickness of the frictional layer. The method is restricted to the case where the effects, caused by separation of frictional layer, are small. Then the total profile drag can be expressed solely by quantities derived from the velocity distribution in the frictional layer immediately at the trailing edge" (p. 1).

Flight-test data and wind-tunnel data on suction profiles are substantially in agreement. The lift values found in the model test can be actually flown and used as a basis for the design. To visualize the action of the suction, the flow conditions with and without suction on the upper surface were photographed; figures 12 to 15 are sections of the film.

"Of the two fundamental cycles employed in combustion turbines, namely, the explosion (or constant-volume) cycle and the constant-pressure cycle, the latter is considered more in detail and its efficiency is derived with the aid of the cycle diagrams for the several cases with adiabatic and isothermal compression and expansion strokes and with and without utilization of the exhaust heat. Account is also taken of the separate efficiencies of the turbine and compressor and of the pressure losses and heat transfer in the piping. The results show that without the utilization of the exhaust heat the efficiencies for the two cases of adiabatic and isothermal compression is offset by the increase in the heat supplied" (p. 1).

"The methods of conformal transformation up to the present have been applied to the potential flows in the rotation of solid bodies only to a limited extent. This report deals with aspects of centrifugal pumps and turbines such as: the complex potential for rotation, potential for the flow due to the blade rotation, velocities at the blade tip, comparison with "infinite number of blades," and a variable number of blades" (p. 1).

The fact that by the use of tetraethyl lead a number of otherwise unsuitable fuels could be made to meet engine requirements was not sufficiently appreciated. While use of tetraethyl lead is limited, the addition of special leaded fuels that increase the octane number is a requirement for many fuels. In this connection, the extent to which the action of tetraethyl lead through the addition of knock-resistant hydrocarbons to the base gasoline is influenced, is quite important. To the elucidation of this problem and of the storage stability of leaded fuels, the present report is dedicated.

"The torsion of box beams of rectangular section, the edges of which are strengthened by flanges, and of which one side is lacking, is analyzed by the energy method. The torsional stresses are generally taken up by the bending of the two parallel walls, the rigidity of which is augmented by the third wall. The result was checked experimentally on duralumin and plywood boxes. The torsion recorded was 10 to 30 percent less than that given by the calculation, owing to self-stiffening" (p. 1).

A method is developed with no neglect of certain factors in mass flow of air and in the drag of the heated radiator, i.e., one under actual operating conditions, as compared with the corresponding values in the cold state, may be simply computed. Although a symmetrical duct radiator has been used to bring out the flow relations, the results apply equally as well to the unsymmetrical radiator shapes usual in airplane construction.

The experimental methods at the Guidonia towing basin are discussed including specifications. Some of the components examined are the bridge towing carriage, side towing carriage, catapult installation, and dynamometer systems. Tests were performed on hulls and floats, as well as motor boats and torpedo shaped bodies. Theoretical investigations were also performed to determine pressure distributions on geometrically simple bodies, propagation of small wave motions, and planing and submerged surfaces.

Following a summary of the multiplicity of domestic and foreign floats and a brief enumeration of the requirements of floats, the essential form parameters and their effect on the qualities of floats are detailed. On this basis a standard float design is developed which in model families with varying length/beam ratio and angle of dead rise is analyzed by an experimental method which permits its best utilization on any airplane.

This report presents some of the problems concerning tests of helicopters, such as forced landings, controllability and stability, general safety, piloting maneuvers, performance, servicing, and the production of lift of a propeller. Test flights are described including a 67.67 mph flight by Hanna Reitsch.

The flame photographs obtained with combustion-chamber models of engines operating respectively, with turbulence chamber and air-storage chambers or cells, provide an insight into the air and fuel movements that take place before and during combustion in the combustion chamber. The relation between air velocity, start of injection, and time of combustion was determined for the combustion process employing a turbulence chamber.

The object of the present report is to ascertain the relationship of the circulation distribution over the wing and of the lift to the height and position of the end plate. The side forces and moments on the end plates were also determined. It is found that moving an end plate of certain length up from the symmetrical position, is followed by a slight increase of the total lift.

"This paper reports on 4-component balance measurements with and without angle of sideslip made on an airfoil with end plate at one tip. In addition, pressure distribution measurements on the end plate served as a basis for the determination of the forces on the end plate and for the bending moments" (p. 1).

This report contains a description of a new spinning-test arrangement wherein the otherwise customary rotation of the model about a fixed axis is abandoned in favor of a corresponding rotation of the air stream. The advantage of this method lies in the fact that the model is at rest while the spin is recorded. In this manner it is possible to secure systematic results with little loss of time while employing 3- or 6-component wind-tunnel balances. The troublesome equalization of the mass forces is eliminated and the flow phenomena are accessible to direct observation.

Based on the universal laws of turbulent velocity distribution at rough and smooth walls, there is in the present work presented a method that allows surface roughness tests and in particular, measurements on the roughness of ship surfaces to be carried out in a much simpler manner. The types of roughness investigated were in the form of flat, rough plates installed in a square-section rectangular channel, the other three walls always being smooth. Twenty-one plates of various roughness were investigated, the roughness elements being the following: spheres of diameter 0.41 and 0.21, respectively, spherical segments, cones, and "short" and "long" angles.