Memorandum presenting an analysis of a large number of liquid-metal-to-air heat-exchanger cores for the nuclear-powered liquid-metal turbojet cycle to determine which types yield the best overall net thrust per total engine weight. The performances of all exchangers considered were initially evaluated at a median condition. The performance of the best of each of the four types was compared with that of a shell-and-tube exchanger with the air flowing through the tubes, operating at the same condition.

Report presenting an experimental investigation of the airflow stability of scoop-type normal-shock inlets located on the fuselage of a model of an interceptor or fighter-type airplane. Pressure recovery and amplitude of pressure pulsations were measured for several Mach numbers and mass-flow ratios.

Report presenting an investigation to determine the longitudinal and lateral stability characteristics of an airplane configuration with a trapezoidal wing with a modified hexagonal airfoil section and a cruciform tail with 5 degrees semiangle wedge section in the 9- by 9-inch Mach number 4 blowdown jet.

Report presenting an investigation to determine the longitudinal and lateral control characteristics of an airplane configuration with a trapezoidal wing with modified hexagonal airfoil section and a cruciform tail with 5 degree semi-angle wedge section. Testing was conducted with the complete model and with the upper or lower vertical tail removed.

Report presenting testing on a 60 degree delta-wing XF-92A airplane at a variety of Mach numbers to obtain measurements regarding buffet-induced fluctuations in normal acceleration and of fluctuations in structural shear load of the left wing. The altitudes tested ranged from 25,000 to 38,000 feet. Results regarding the buffet boundary, wing flow conditions, buffet frequencies, buffet intensities, and a comparison to buffeting of other airplanes are provided.

Report presenting testing of a model of a supersonic airplane configuration with a 40 degree sweptback wing with circular-arc sections at Mach numbers 0.85 and 1.15 to obtain lateral stability data at low lift and to evaluate the test and analysis technique. Results regarding time history, trim characteristics, amplitude ratio and phase of rolling angular acceleration to angle of sideslip, sideslip derivatives, moment derivatives due to yawing, and a comparison of present data with previously obtained data are provided.

Report presenting a determination of the individual stage performance for a 10-stage axial-flow compressor from circumferentially fixed radial rake measurements of total temperature and total pressure obtained at the discharge of each stage. Results regarding compressor performance, stage performance, and some general remarks are provided.

Report presenting an investigation of the effects of wing and tail modifications on the low-speed stability characteristics of a model with thin 40 degree swept wings of aspect ratio 3.5. The main purpose was to improve some of the undesirable longitudinal stability characteristics observed in flight of several airplanes with similar wing geometry. The use of flaps, the position of the horizontal tail, and the use of chord extensions are all explored as possible solutions.

Report presenting component performance data for one modification of a 16-stage compressor and a 3-stage turbine to determine the matched performance characteristics of an engine with those components. The compressor surge line and infinite exhaust-nozzle-area equilibrium operating line restricted the region of matched compressor-turbine operation. Results regarding the engine operation with modified compressor and three-stage turbine, effect of leakage on engine operation, component efficiencies, and operation in the surge region are provided.

"An investigation was made of the trim and dynamic response characteristics of the free-floating horizontal tail of a 1/7-scale model of the complete tail of the Grumman XF10F-1 airplane in the Langley 8-foot transonic tunnel at Mach numbers up to 1.13. The complete tail was mounted in the tunnel on a 3 degree conical support body. Various configurations were investigated. A loss in damping of the horizontal tail at transonic speeds was shown by both tunnel and flight tests" (p. 1).

Report presenting an investigation of the aerodynamic interference effects associated with a missile configuration, consisting of a pointed body of revolution with one or two ramjet engines strut-mounted in a vertical plane through the center line of the body, at several engine locations relative to the body and a range of angles of attack. The experimental data indicated increases in slope of the normal force curve with outward movement of the engines. Results regarding the characteristics of isolated components, characteristics of representative configurations, interference effects, and effect of engine location on lift-drag ratio are provided.

Memorandum presenting an investigation conducted to explore the characteristics of metal-hydrocarbon combustion, to determine the effect of fuel-air ratio on the combustion efficiency, and to determine how the metal and hydrocarbon separately contribute to the overall combustion of several slurries. Results regarding an evaluation of the sampling method, combustion efficiency, effective metal weight fraction, effective hydrogen-carbon ratio, and heat of combustion per pound of air are provided.

Memorandum presenting a 10-stage axial-flow compressor designed for use as a research unit in which the problems associated with the compounding of high performance stages could be studied. The overall performance characteristics of the compressor, as determined experimentally, are included.

Report presenting experimental data from force and pressure tests on a large-scale, semispan, wing-fuselage model. Longitudinal force and moment characteristics are given for the model with various combinations of slat spans. The wing had 45 degrees of sweepback, an aspect ratio of 6, a taper ratio of 0.5, and an NACA 64A010 section normal to the quarter-chord line of the unswept panel and had partial-span slats, aileron, and double-slotted flaps equipped.

Report presenting testing of an impulse-type supersonic compressor rotor with stators tested in Freon-12 over a range of equivalent tip speeds and weight flows. A static pressure ratio of 1.83 and an efficiency of 84.7 percent were obtained at 69.1 percent of the design speed of 1604 feet per second in air.

An investigation of tail-pipe burning was conducted in the NACA Lewis altitude wind tunnel with a full-scale turbojet engine and an 29-inch-diameter tail-pipe burner. Effects of fuel distribution and number and arrangement of stages on performance and operational characteristics of several fuel-cooled flame holders are presented and discussed. Operation with a three-stage flame holder having the large stage upstream was the most efficient. Combustion efficiency was slightly increased at high altitudes by injecting fuel upstream of the flame holder.

"At the request of the Air Materiel Command, an investigation was made in the Langley free-flight tunnel to determine the longitudinal stability and control characteristics of models coupled together in a tandem configuration for aerial refueling similar to one proposed by the Douglas Aircraft Company, Inc. Static force tests were made with 1/20-scale models of the B-29 and F-80 airplanes to determine the effects of rigidly coupling the airplanes together. The Douglas configuration differs from the rigid configuration tested in that it provides for some freedom in pitch and vertical displacement" (p. 1).

An investigation has been conducted in the Cleveland 18- by 18-inch supersonic tunnel at a Mach number of 1.85 and angles of attack from 0 deg to 5 deg to determine optimum design configurations for a convergent-divergent type of supersonic diffuser with a subsonic diffuser of 5 deg included divergence angle. Total pressure recoveries in excess of theoretical recovery across a normal shock at a free-stream Mach number of 1.85 wore obtained with several configurations.

Report presenting an investigation in the two-dimensional low-turbulence tunnels to develop optimum double-slotted-flap configurations for seven thin NACA airfoil sections. Each was equipped with the same flaps and measured at the same Reynolds numbers. Results regarding the lift characteristics and pitching moment are provided.