Report presenting an investigation of the effectiveness of suction slots as a means of extending the laminar boundary layer in flight at high Reynolds numbers on an NACA 35-215 airfoil. The results showed that, with a slot spacing of about 5 percent of the chord, the laminar boundary layer could be maintained to or slightly beyond 45 percent of the chord.

Note presenting a least-squares procedure adapted to numerical calculation for the approximate solution of the Prandtl lifting-line equation. Sufficient data are tabulated to permit a solution of the equation by purely numerical methods for an arbitrary symmetrical variation of the chord and the angle of attack.

Report presenting an investigation of the shape of stress-strain curve for a material, especially when the material is subjected to compression, which may cause materials to become unstable at stresses beyond the elastic range. The ratio of stresses to effective modulus is explored in equation form.

Note presenting an effective value of Poisson's ratio for 18:8 Cr-Ni steel computed from values of tensile and torsional moduli of elasticity obtianed in earlier investigations by use of an appropriate formula.

From Summary: "The various types of hydrodynamic instability - including porpoising, skipping, and yawing - that may be encountered during take-off or landing of a flying boat are described and the piloting technique required for efficient take-offs and landings is discussed. Suggestions are made for assisting a pilot to become familiar with the take-off and landing qualities of a flying boat that is new to him."

Report re-examining known procedures for handling general resistance testing on flying-boat hull models, with particular attention paid to saving test time and improving the usefulness of the results to designers. While specific testing will likely always be needed, the procedures given in the report for condensing resistance data should make data analysis easier to apply to design.

Report presenting wind-tunnel testing in two-dimensional flow to investigate the aerodynamic characteristics of a flap balanced by a large overhang linked to deflect more slowly than the flap. Three lengths of blunt-nose overhang were tested linked to a 0.30-airfoil-chord straight-contour flap on an NACA 66-009 airfoil. Results regarding lift, hinge moment, drag, pitching moment, and practical considerations are provided.

Report presenting measurements in the full-scale tunnel of the pressure distribution over the horizontal tail surface of a typical pursuit airplane in order to determine the effects of propeller operation and angle of yaw on the tail load distribution. Most of the tests were made with the propeller operating to simulate climb conditions, high-speed dives, and pull-ups to various normal accelerations for a range of angles of yaw. Results regarding chordwise pressure distributions, spanwise distributions of normal-force coefficient, airflow measurements, and tail-load asymmetry are provided.

"The relation between the elevator hinge-moment parameters and the control forces for changes in forward speed and in maneuvers is shown for several values of static stability and elevator mass balance" (p. 1). Factors affecting stability positively and negatively are presented and potential modifications to the elevator control system are provided. The amount of solid friction present was found to be one of the greatest predictors of instability.

Report presenting compression testing on several series of flat panels with Z-section stiffeners with varying relative dimensions. The data presented show the effect of dimension ratio on the buckling stress for the sheet and on average stress at maximum load.

Report discusses an investigation that was conducted to compare the strength and tightness of machine-countersunk flush-riveted joints assembled with NACA flush rivets and a type of commercial flush rivet. A comparison was also generated between the strength and tightness of counterpunched flush-riveted joints assembled with the same types of rivet. NACA's flush-riveted joints tended to be stronger and tighter than the commercial joints.

Report presenting testing made on a Wright 1820-G single-cylinder engine to determine the effect of operating variables and the effect of shape and size of the exhaust stack on the visibility of exhaust gases for individual-stack installations. Flame damping was improved by decrease in nozzle-exit area, increase in stack length, and reduction in hydraulic diameter of the exhaust jets. Results regarding the characteristics of exhaust flames and damping of exhaust flames are provided.

An analysis has been made of the drag losses in airplane flight of cross-flow plate and tubular intercoolers to determine the cooling-air weight flow and pressure drop that give a minimum drag loss for any given cooling effectiveness and, thus, a maximum power-plant net gain due to charge-air cooling. The drag losses considered in this analysis are those due to (1) the extra drag imposed on the airplane by the weight of the intercooler, its duct, and its supports and (2) the drag sustained by the cooling air in flowing through the intercooler and its duct. The investigation covers a range of conditions of altitude, airspeed, lift-drag ratio, supercharger-pressure ratio, and supercharger adiabatic efficiency. The optimum values of cooling air pressure drop and weight flow ratio are tabulated. Curves are presented to illustrate the results of the analysis.

The effect of internal cooling on the knock-limited performance of an-f-28 fuel was investigated in a CFR engine, and the following internal coolants were used: (1) water, (2), methyl alcohol-water mixture, (3) ammonia-methyl alcohol-water mixture, (4) monomethylamine-water mixture, (5) dimethylamine-water mixture, and (6) trimethylamine-water mixture. Tests were run at inlet-air temperatures of 150 degrees and 250 degrees F. to indicate the temperature sensitivity of the internal-coolant solutions.

Report presenting the effect of internal cooling on the knock-limited performance of AN-F-28 fuel in a CFR engine with the following internal coolants: water, methyl alcohol-water mixture, ammonia-methyl alcohol-water mixture, monomethyllamine-water mixture, dimethylamine-water mixture, and trimethylamine-water mixture.

"Two graphical methods are presented for determining the stick-free neutral point, and they are extensions of the methods commonly used to determine the stick-free neutral point. A mathematical formula for computing the stick-free neutral point is also given. These methods may be applied to determine approximately the increase in tail size necessary to shift the neutral point (stick fixed or free) to any desired location on an airplane having inadequate longitudinal stability" (p. 1).

Report presenting an investigation of the effectiveness of suction slots a a means of extending the laminar boundary layer in flight at high Reynolds numbers using an NACA 35-215 airfoil. Tests were made over a range of indicated airspeeds, lift coefficients, and Reynolds numbers. Results regarding boundary-layer control, air-intake distributions, character of the boundary layer, total-intake rate, and profile-drag coefficient are provided.

Report presenting a tabular method for determining the span load distribution at high Mach numbers by utilizing high-speed airfoil section data. This method, which is also called the generalized method, is an easily applied process of successive approximations by which a general application of the lifting-line theory may be used to determine the span load distribution for wings composed of sections with arbitrary lift curves. An example is provided to show how the method is used.

Report discusses tests conducted using a model of a four-engine long-range flying boat with a 30 degree V-step and two different transverse steps of comparable positions and depths. The limits of stability, landing speed, and landing characteristics of the different models are presented.

Report presenting tests in the gust tunnel on a scale model of the XBDR-1 airplane to verify the calculated effective gust factor. Tests were made for three gust shapes, one forward velocity, and one wing loading. The test results and analysis were in good agreement and the results of the analysis indicated that there was an appreciable change in effective gust factor for the center-of-gravity movement considered.

Results are presented for tests of two wings, an NACA 230-series wing and a highly-cambered NACA 66-series wing on a twin-engine pursuit airplane. Auxiliary control flaps were tested in combinations with each wing. Data showing comparison of high-speed aerodynamic characteristics of the model when equipped with each wing, the effect of the auxiliary control flaps on aerodynamic characteristics, and elevator effectiveness for the model with the 66-series wing are presented. High-speed aerodynamic characteristics of the model were improved with the 66-series wing.

"A model of a flying boat was tested to determine the landing characteristics when the depth of the step was reduced to zero by means of a retractable planing flap on the forebody" (p. 4). The results of stability and resistance testing are presented.

"Strength tests were made on two sets of beams having webs with large circular lightening holes. The main conclusion drawn from the tests is that allowable web stressed derived from pure shear tests and allowable flange stresses derived from compression tests cannot be applied in the design of beams without making corrections for interaction" (p. 1). Pure shear tests and beam tests were performed and the circumstances of failure were investigated.

Report presenting corrections to the velocities near a cowling-flap tip in order to determine jet-boundary corrections to cowling-flap-outlet pressures. The presence of the low-energy air leaving the flap opening was taken into account by so shaping the nacelle model that its outer surface represented the stream surface leaving the flap tip. Copper was found unsatisfactory for use as electrode material.