Summary: An EVESR MKI prototype fuel bundle was fully instrumented and operated intermittently for a 5-month period at the Pacific Gas and Electric Company’s Moss Landing Power Station. The vessel was operated up to 1000 psi with steam flows from 3000 to 26,600 lb/h, and steam inlet temperatures up to 825 degrees F. Data was recorded for blowout, vibration, flow distribution, heat transfer and pressure drop. The mechanical integrity of the fuel bundle, riser, and jumper system was satisfactory and considered to be of adequate design. No significant vibrations were noted during the various phases of operation. Average flow distribution in three of the inner tubes showed an average variation of 5 percent from equal distribution. The center and corner tubes were low and the side tube was high. Maximum deviation, from an equal one, measured 12 percent. Blowout of the flooded fuel bundle was accomplished with dry or significantly wet 1000 psia inlet steam, that steadied out to a minimum flow of 1250 lb/h. Blowout times were estimated at less than a minute for all flows above 1250 lb/h, and times in the vicinity of 2000 lb/h were estimated to be in the order of 5 to 15 seconds. …

From introduction: "This is the eighteenth in a series of quarterly reports which cover the progress and results from the conceptual designs, economic evaluations and research and development work performed by the General Electric Company as part of Contract AT(01-3)-189, Project Agreement No. 13."

Summary: An analytical study of the stability of the Big Rock Nuclear Reactor has been performed for the plant as built, and supplements a previous design stability study. The plant has been determined by this analysis to be very stable under every mode of operation anticipated during Phase I of the development program testing. Even under conservative assumptions of system parameters the minimum calculated gain and phase margins do not go below 13.0 db and 46 degrees, respectively. (Nor are these both reached simultaneously for the same operating condition.) These are characteristics of a very stable, well-behaved system. In addition to this analysis, a second, less conservative series of computations was performed to provide expected realistic closed loop data for comparison with Phase I test results. The most responsive test thus predicted occurs at 60 percent power, 1500 psia, minimum flow, and maximum subcooling. For this case the closed loop peak response of power to reactivity occurs at a frequency of 0.90 cycles per second with an amplitude of 3.90 db. This corresponds to an expected open loop gain margin of 16.5 db and a phase margin of 63 degrees. Although knowledge of reactor transfer function is to be determined …

Technical report describing how corrosion data and exposure effects were obtained by subjecting metallic samples, during programmed test runs to flowing sodium in 6 test loops fabricated with various combinations of three selected materials, Type 316 stainless steel, 2 1/4 Cr-1 Mo alloy steel, and 5 Cr-1/2 Mo-1/2 Ti alloy steel. Information produced by each test run, including operational and metallurgical data and analyses, is presented. Data are shown in tables, graphs, and drawings.

Abstract. A program was instituted to study and reproduce the in-reactor intergranular failures of Type-304 stainless steel fuel cladding found in superheated steam. The program was directed toward finding ways to eliminate the cause of failure or to use improved alloys that would be less susceptible to failure. A materials screening test was developed in the out-of-pile superheat facilities with 1.5 ppm chloride added as sodium chloride to the recirculating water in the presence of typical boiling water reactor quantities of oxygen and hydrogen. During the test, the heater sheaths were exposed through several cycles to saturated steam (with its accompanying moisture carryover) and superheated steam. Failure of Type-304 stainless steel was obtained in periods of less than two weeks; the failures were predominantly transgranular. Type-347 and vacuum-melted Type-304 stainless steels failed in this NaCl-cycle test while Inconel-600, Incoloy-800, Hastelloy-X, Type-406 stainless steel, and vacuum-melted Type-310 stainless steel were acceptable. An improved chloride cycle test with 0.5 ppm chloride added as ferric chloride to the recirculating water was developed. An intergranular failure was obtained similar to that experienced in the superheat fuel cladding failures in the superheat in-pile loops in the Vallecitos Boiling-Water Reactor. Sensitized Type-304 and Type-316 stainless steels …

Abstract: The question of how crack-free, protective oxide films can form on zirconium during oxidation when the Pilling-Bedworth ratio is about 1.5 has been considered by a study of the relative plasticity of various forms of zirconia. Hot hardness measurements showed that doping mono-clinic zirconia with iron, nickel, or chromium resulted in softer (more plastic) structures and that yttrium additions slightly reduced the plasticity. Calcia-stabilized cubic zirconia was found to be more plastic than mono-clinic zirconia when tested at temperatures above 200 degrees C. The behavior of anion-deficient oxides indicated that they were more plastic than stoichiometric oxides even though the hardness values were identical at 23 degrees C. The former were free from cracks at the indentions, whereas, stoichiometric oxides exhibited extensive cracking around and between indentions. The behavior of actual, thick (72 microns) oxide films during tensile deformation of oxidized metal samples indicated that considerable plasticity occurs in the oxide at 500 degrees C but that the films are brittle at 23 degrees C. It was concluded that the plasticity of the oxide may be greater than that of the oxygen-contaminated substrate at elevated temperatures and may be the means by which epitaxial strains are minimized.

Technical report describing an analytical investigation made on the mechanism of the "downstream" effect in the corrosion of stainless steel in sodium. A mechanism of iron alloy corrosion is assumed in which the controlling rate is diffusion of iron-oxygen species, probably a FeO-Na2O complex. A mathematical model is developed for the corrosion, and the predicted results agree with the experimental data. The corroding species is probably present in sodium at concentrations of ~10(-8) g Fe/g Na.

Summary: Stainless steel clad nuclear fuel cycle costs can be reduced to those associated with Zircaloy clad fuel or potentially lower by reducing the thickness of the clad tube wall until performance penalties offset the savings associated with the reduction in parasitic neutron absorption. To demonstrate the feasibility and investigate performance capabilities of thin clad fuel rods for power reactor application an assembly was fabricated with 0.0127 cm (5 mil) thick stainless steel cladding tubes for irradiation testing in the Vallecitos Boiling Water Reactor (VBWR). The fuel bundle was placed in the VBWR and irradiation was begun in November, 1961. The irradiation is scheduled to continue until the target exposure of 2.74 x 10(20) fissions/cc (10,000 MWD/T of uranium) average burnup is reached. Destructive examinations of fuel rods will be performed at regular intervals throughout life to determine fuel rod performance.

The extrusion forming of ceramic powders may be economically interesting in the field of nuclear fuel fabrication. When applied to the forming of rod-type uranium dioxide fuel, extrusion processes have been able to produce cylindrical bodies with length-to-diameter ratios much greater than those of the conventional die-pressed pellets. Furthermore, after being sintered, the extrusions have exhibited densities at least as high as those of sintered pellets. Thus, extrusion forming may offer reductions in handling during fabrication and, at the same time, provide a fuel with improved performance characteristics by decreasing the number of discontinuities in the fuel column. This report reviews the production of these extrusions, sets forth some of their characteristics, describes the materials and processes employed in cladding them, and records the pre-irradiation data pertaining to the finished fuel rods and fuel assembly. Irradiation of the fuel assembly in the VBWR was initiated on July 17, 1962.

A method for calculating the frequency response of weighted voids (proportional to reactivity of steam voids) as a function of reactor power is presented.

In this paper arbitrary limits of the general fission source gamma problem are set. Then, by assuming cooling of at least one day, it is shown that only twelve different fission product gamma sources need ever be considered.

This report is submitted to the U. S. Atomic Energy Commission as a final summary safeguards and hazards evaluation of a proposed test reactor at its Vallecitos Atomic Laboratory in Alameda County of California. It is the purpose of this report to provide sufficient data to obtain an AEC facility license for the reactor.

This report presents the reactor description and safeguard evaluation for an open pool research and test reactor being supplied to the State College of Washington, Pullman, Washington, by the General Electric Company.

This report is an amendment to the Preliminary Hazards Summary Report (1) and the Operating Procedures and Emergency Plans (5) for the Dresden Nuclear Power Station, submitted to the United States Atomic Energy Commission on September 3, 1957, and June 5, 1958, respectively.

This Preliminary Hazards Summary Report has been prepared for submission to the United States Atomic Energy Commission in compliance with Part 50 of the regulations governing the licensing of production or utilization facilities, pursuant to the Atomic Energy Act of 1954, as amended, and contains the general information required by 10 CFR 50.34.

A reference design of a large high power density core has been established representing the available technology as of August, 1960. Reference core performance and cost should improve considerably after incorporation of improvements now under study.

The General Electric Company is proceeding with an irradiation program to proof test a representative array of Savannah I fuel rods. Irradiation of a test assembly containing Savannah I fuel rods has begun and it is proposed that the results of this irradiation will permit an advance evaluation of the fuel performance and fuel burnup in the Savannah I reactor. This report covers the first two quarters of the reporting period. All aspects of the subject program have been consolidated and applicable portions are discussed in some detail.

Equipment and techniques for remote examination of irradiated fuel assemblies applicable to the Maritime Program are described. The following subjects are covered: visual and photographic examination, dimensional measurements, gamma activity scanning, fission gas release and fuel rod void volume determinations, density measurements, metallographic examination, and radiochemical burnup analysis.