"Through the utilization of the "Magnus effect" on the Flettner rotor ship, the attention of the public has been directed to the underlying physical principle. It has been found that the Prandtl boundary-layer theory furnishes a satisfactory explanation of the observed phenomena. The present article deals with the prevention of this separation or detachment of the flow by drawing the boundary layer into the inside of a body through a slot or slots in its surface" (p. 1).

The mutual influences of compression shocks and friction boundary layers were investigated by means of high speed wind tunnels.Schlieren optics provided a clear picture of the flow phenomena and were used for determining the location of the compression shocks, measurement of shock angles, and also for Mach angles. Pressure measurement and humidity measurements were also taken into consideration.Results along with a mathematical model are described.

The nature of turbulent flow through pipes and around obstacles is analyzed and illustrated by photographs of turbulence on screens and straighteners. It is shown that the reversal of flow and of the resistance law on spheres is not explainable by Prandtl's turbulence in the boundary layer. The investigation of the analogous phenomena on the cylinder yields a reversal of the total field of flow.

"In connection with an earlier report on the lifting vortex sheet which forms the basis of the following investigations this will show how the methods developed there are also suitable for dealing with the air forces for a wing with a circulation variable with time. The theory of a propulsive wing flapping up and down periodically in the manner of a bird's wing is developed. This study shows how the lift and its moment result as a function of the flapping motion, what thrust is attainable, and how high is the degree of efficiency of this flapping propulsion unit if the air friction is disregarded" (p. 1).

This report presents the results of testing on a glider designed and built by the College Aviation Group. The design and construction were based on the following principles: 1) the glider will be made to descend as slowly as possible; 2) rigidity and resistance were arranged to meet the conditions of varied loads; 3) construction is as simple as possible; 4) and great ease in assembling and dismounting have been sought.

This report covers a series of tests on thin flat elastic strips restrained at two parallel edges and subjected to shear by conversely directed stresses. Theoretical treatments, particularly those of Lilly, Southwell and Skan, and Timoshenko are briefly outlined. The problem to be solved by these tests was to find out whether, and to what extent the conditions and assumptions upon which the calculations are based are complied with in the tests.

This report begins by indicating several simple principles concerning the velocity distribution over the blades of a lifting propeller of diameter D, revolving at n revolutions per second, and animated by a horizontal movement of translation at speed V. The calculation, compared with the test data, has shown that the aerodynamic action of the air on the blades depends almost only on the velocity components in a plane at right angles to the blade span. A history of gyroplane and gyrocopter development is presented as well as the advantages in using both types of craft.

This report provides a summary of the important steps to be taken in combating airplane fires. Some considerations and ways of preventing fires from developing are provided.

Memorandum describing the results of the Royal Aero Club light airplane competition and some of the history surrounding the event. A list of the planes that participated and an analysis of the performance of the various aircraft are provided.

From Summary: "Experiments have been made to determine the nature of turbulence in the wake of a two-dimensional airfoil at low speeds. The experiments were motivated by the need for data which can be used for analysis of the tail-buffeting problem in aircraft design. Turbulent intensity and power spectra of the velocity fluctuations were measured at a Reynolds number of 1.6 x 10(exp 5) for several angles of attack. Total-head measurements were also obtained in an attempt to relate steady and fluctuating wake properties."

"The proposed device tends to render the lateral stabilization of airplanes easier and more efficacious. The proposed solution is to mount the ailerons independently, in such a manner that they can turn freely, under the action of the relative wind, about an axis located in front of the extreme position of the center of the lift" (p. 1).

Predicated on the assumption of certain normal conditions for engine and propeller, simple expressions for the static and dynamic stresses of propeller blade roots are evolved. They, in combination with the fatigue strength diagram of the employed material, afford for each engine power one certain operating point by which the state of stress serving as a basis for the design of the root is defined. Different stress cases must be analyzed, depending on the vibration tendency of engine and use of propeller. The solution affords an insight into the possible introduction of different size classes of propeller.

"The idea is advanced of making a supersonic nozzle by producing one, two, or three successive turns of the whole flow; with the result that the wall contour can be calculated exactly by means of the Prandtl-Meyer "Lost Solution" (p. 1).

"The present report deals with the determination of the impact stresses in the bulkhead floors of a seaplane bottom. The dynamic problem is solved on the assumption of a certain elastic system, the floor being assumed as a weightless elastic beam with concentrated masses at the ends (due to the mass of the float) and with a spring which replaces the elastic action of the keel in the center. The distributed load on the floor is that due to the hydrodynamic force acting over a certain portion of the bottom" (p. 1).

Three different Marcel Besson airfoils are investigated in terms of maximum lift, maximum fineness, minimum required power, and wing section drag. Comparisons are then made between the three airfoils.

Similarities in the study of aviation accidents in different countries are made as well as statistics on the causes of those accidents.

The present report is a comparison of the experimentally defined temperature and heat output of cooling fins in the air stream with theory. The agreement is close on the basis of a mean coefficient of heat transfer with respect to the total surface. A relationship is established between the mean coefficient of heat transfer, the dimensions of the fin arrangement, and the air velocity.

"At the ends of a monocoque fuselage concentrated axial forces in the skin must generally be taken up. Such axial forces must also be taken up in the case of other members where axial forces from the neighboring stressed skin construction must be considered. In order to take up these axial forces two bulkheads or reinforcing frames may be arranged at the positions where the forces are applied" (p. 1).

In the present study it is proposed to provide an equipment permitting the study of the propagation of the region of reaction in mixtures of air and carbureted gases enclosed within a cylinder. Ignition is produced at the end of compression by an electric spark. With this apparatus it is proposed to determine: 1) the influence of the richness of the explosive mixture on the rate of flame propagation; 2) the influence of the degree of volumetric compression on one of the hydrocarbons; 3) the influence of the variation of initial temperature of the mixture before compression; 4) the influence of tetraethyl-lead on the propagation - notably on the formation of the explosive wave.

Memorandum presenting the experimental results of tests to confirm the contribution to the study of normal burning in gaseous carbureted mixtures.

Axial blowers are gaining importance as aircraft engine superchargers. However, the pressure head obtainable per stage is small. Due to the necessary great number of stages, the physical length of the blower becomes too great for an airworthy device. This report discusses several types of construction that permit a reduction in the length of the blower.

From Summary: "The resistance coefficients of commercial types of round wire grids were examined for the purpose of obtaining the necessary data on supercharger test stands for throttling the inducted air to a pressure corresponding to a desired air density. The measurements of the coefficients ranged up to Reynolds numbers of 1000. In the arrangement of two grids in tandem, which was necessary in order to obtain high resistance coefficients with the solidity, that is, mesh density of grid, was found to be accompanied by a further relationship with the mutual spacing of the individual grids."

The icing hazard can, in most cases, be avoided by correct execution of the flights according to meteorological viewpoints and by meteorologically correct navigation (horizontal and, above all, vertical). The zones of icing hazard are usually narrowly confined. Their location can be ascertained with, in most cases, sufficient accuracy before take-off.

"To investigate the laws of flow of compressible fluids in pipes, tests were carried out with air flowing at velocities below and above that of sound in straight smooth pipes. Air was chosen as the flow medium. In order that the effect of compressibility may be brought out most effectively, the velocity should lie between 100 and 500 m/s (200 and 1,000 mph); that is, be of the order of magnitude of the velocity of sound in air. The behavior of the compression shock in a smooth cylindrical pipe was also investigated" (p. 1).