Memorandum presenting the effectiveness of a body flare as a pitch-stabilizing device and a body flap as a pitch-control device investigated experimentally at Mach numbers from 3.00 to 6.25. The basic test body was rotationally symmetric and consisted of a fineness ratio 3 nose followed by a fineness ratio 9 afterbody. Results regarding the stability of the flared body, effect of body flap on lift and drag, trim conditions, flow visualization studies, and comparison of theory and experiment are provided.

Memorandum presenting an investigation to determine the drag, longitudinal stability, and lateral stability characteristics of a model of a fighter-type airplane. Several modifications were made to the model in an attempt to eliminate pitch-up.

Report presenting a wind-tunnel investigation at low speed to determine the lateral control characteristics of a 51.3 degree sweptback-wing model equipped with either plain or stepped spoiler ailerons with a fixed projection of 5-percent-wing chord and various spans and spanwise locations. The results indicated that spanwise rolling-effectiveness charts of flap-type ailerons can not be used to predict effectiveness of spoiler-type ailerons on swept wings. Results regarding the wing aerodynamic characteristics with spoiler ailerons retracted, wing aerodynamic characteristics with spoiler ailerons projected, and a comparison of spoiler-type and flap-type ailerons.

Report presenting the effectiveness of a 50-percent-semispan, constant-percent-chord elevon, and of upper-space spoilers as lateral control surfaces for a wing-fuselage combination with a wing swept back 63 degrees over a range of Mach numbers. For the elevon, results indicated that only about half of the predicted rolling-moment effectiveness was realized. The spoilers were found to be inferior to the elevons for lateral control because of a rapid loss of effectivness above an angle of attack of 4 degrees.

Memorandum presenting several new methods that have been designed for obtaining electrical connection to thermocouples that are revolving at high speeds. Two general types of pickup system are described with modifications for special installations. Both pickup systems have been proved to transmit an accurate signal from a revolving thermocouple to within 0.045 millivolt at contact sliding speeds up to 5400 feet per minute.

"The tendency for the jet engine rotor to continue to rotate after crash presents the probability that crash-spilled combustibles suspended in the air or puddled on the ground at the engine inlet may be sucked into the engine. Studies with jet engines operating on a test stand and full-scale crashes of turbojet-powered airplanes showed that combustibles drawn into the engine in this way ignite explosively within the engine. Experiment showed that the gas flow through the engine is too rapid to permit the ignition of ingested combustibles on the hot metal in contact with the main gas stream" (p. 623).

At the request of the Bureau of Aeronautics, Department of the Navy, National Advisory Committee for Aeronautics has conducted a preliminary investigation at high subsonic speeds of the static longitudinal and lateral stability characteristics of a 0.05-scale model of the Convair F2Y-1 water-based fighter airplane. The tests covered a Mach number range from 0.5 to 0.94 and corresponding Reynolds numbers, based on the wing mean aerodynamic chord, from 3.3 x 10(exp 6) to 4.3 x 10(exp 6). The maximum angle-of-attack range (obtained at the lower Mach numbers) was from -2 degrees to 25 degrees. Sideslip angles from -4 degrees to 12 degrees also were investigated. The investigation included effects of various arrangements of wing fences and of rocket packages.

Good internal performance over a wide range of flight conditions can be obtained with either a plug nozzle or a variable ejector nozzle that can provide a divergent shroud at high pressure ratios. For both the ejector and the plug nozzle, external flow can sometimes cause serious drag losses and, for some plug-nozzle installations, external flow can cause serious internal performance losses. Plug-nozzle cooling and design of the secondary-air-flow systems for ejectors were also considered .

Report presents information about free-flight rocket-propelled model testing to determine the effect of some wing geometry variables on low lift drag at a range of Mach numbers. Results regarding the effect of airfoil section, wing nose droop and nose flaps, plan form, and wing vertical position are provided.

"A two-dimensional investigation utilizing pressure-distribution measurements and schileren photographs has been made of the flow and force characteristics of slab-sided airfoils of 2-percent thickness at transonic Mach numbers. The airfoils had various combinations of elliptically shaped leading and trailing edges from a fineness ratio of 0 to 10. The aerodynamic characteristics and an analysis of the flow past the models are presented" (p. 1).

Report presenting a flight investigation conducted on a 35 degree swept-wing fighter airplane with two different horizontal-tail heights. The longitudinal stability and buffet characteristics were compared for the two configurations. Results regarding longitudinal stability, buffet, and pitch-up intensity are provided.

Pressure distributions were measured over rectangular wings of aspect ratio 2 and triangular wings of aspect ratios 2 and 4 at Mach numbers of 2.46 and 3.36. The investigation includes some comparison of the effects of Mach number, Reynolds number, and thickening the wing root sections on the loading.

An investigation of the effectiveness of a body flare as a pitch-stabilizing device and a body flap as a pitch-control device over a range of Mach numbers. Experimentally defined increments in lift and drag due to flap deflection are compared at Mach number 5 with the predictions of generalized shock-expansion theory and Newtonian impact theory. Results regarding the stability of the flared body, effect of body flap on lift and drag, trim conditions, flow visualization studies, and a comparison of theory and experiment are provided.

Results of a survey investigation of the J71-97 experimental three-stage turbine equipped with a first-stator area 70 percent pf design are presented and compared with the turbine with a first-stator area 97 percent of design.

Report presenting an experimental determination of the flow fields near swept- and unswept-wing-fuselage combinations at zero sideslip as determined experimentally at low speed for various spanwise and vertical locations and angles of attack as variations with chordwise distance. Results regarding the swept-wing-fuselage flow fields, unswept-wing-fuselage flow fields, and a comparison of wing-fuselage and fuselage-alone flow fields are provided.

Internal performance of normal-shock rectangular, circular, and scoop inlets and of external-compression inlets experimentally obtained with varying immersion in a turbulent boundary layer. Recoveries varied from about 95 percent of theoretical in the free stream to 80 percent with complete immersion, while the corresponding mass flows were usually above 95 percent of theoretical. Turning of the flow through 10 degrees caused losses in pressure recovery of 0.03 to 0.07. External compression did not improve pressure recovery in the boundary layer. Average distortion at critical operation for all inlets was 5 percent.

An investigation was conducted in the NACA Lewis 10- by 10-foot supersonic wind tunnel to evaluate the performance of three burner configurations in a 16-inch ram jet with gaseous hydrogen as fuel. Data were obtained over a fuel-air-ratio range from 0.0030 to 0.0260 (stoichiometric = 0.0292) at a free-stream Mach number of 3.0 and 0 degree angle of attack. The exit nozzle-throat area ratios employed were 0.60 and 0.75.

An evaluation of the effect of geometric design variables on the performance of a 16-inch-diameter ram-jet combustor total pressures from 7 to 44 inches of mercury absolute. Equivalent ratio was varied from 0.1 to 1.0 at a combustor inlet temperature of 1100 degrees R.

The basic ideas of the slender-body approximation have been applied to the nonlinear transonic-flow equation for the velocity potential in order to obtain some of the essential features of slender-body theory at transonic speeds. The results of the investigation are presented from a unified point of view which demonstrates the similarity of slender-body solutions in the various Mach number ranges. The transonic area rule and some conditions concerning its validity follow from the analysis. (author).

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Price Daniel, regarding a legal question submitted for clarification: The source of the fees due the Tax Assessor-Collector of Cameron County for assessing State ad valorem taxes, since the entire tax is now remitted to Cameron County.

This manual discusses basic radiological safety and APPR-1 radiation monitoring. It then provides radiation protection instructions.

Abstract: Presented herein is the preliminary design of a natural uranium, graphite moderated, CO2-cooled reactor and power plant similar to, but larger than, the British Calder Hall plant, with a net electrical output of 130 MWE.

None

Aluminum capsules with Al inserts and He atmospheres and containing 4 strips of Eu/sub 2/O/sub 3/-stainless steel were measured in the Reactivity Measurement Facility at MTR, both before and after irradiation. (T.R.H.)