This is the summary report on the ARF Project C 127, entitled "Preliminary Studies Related to Radioactive Fallout", covering the period from April 1, 1959, to April 29, 1960.

Abstract: "The accuracies which can be achieved in analog recording systems are for the most part tape limited. While reasonable variations in tape speed do not directly affect the accuracy, such variations result in improper tape tensioning, which in turn results in poor head-to-tape contact. The quality of the tape transport mechanism should be such that the error introduced by improper head- to tape contact is less than tape errors. Some additional equipment is necessary in setting up a tape recorder for a given experiment. The amplitude of the input pulse spectura to the recorder should be adjusted for optimum value and, if possible, the counting rate should be adjusted to obtain good tape utilization. An oscilloscope is probably adequate to satisfy both conditions."

This bibliography contains 147 references on the fabrication of beryllium. References are also given on the brazing, casting, cladding, extrusion and welding of beryllium and some beryllium-rich alloys. The bibliography is limited to the period 1950 - 1959. references are arranged alphabetically by title, with author and subject indexes provided. Sources used in compiling this bibliography are: Abstracts of Classified Reports, ASM Review of Metal Literature, Bibliographies of Interest to the Atomic Energy Program - Classified and Unclassified Versions, Engineering Index, Nuclear Science Abstracts, TISE, List of Bibliographies in the Atomic Energy Program.

From introduction: This report details the seismic measurements by the USGS during the pre-Gnome high-explosives tests near Carlsbad, New Mexico.

Technical report describing the methods used for forming wave guides for installations of microwave diagnostic systems for use in Project Sherwood. A machine designed by the author is described along with details of its use.

Abstract. A fast-slow coincidence scintillation spectrometer for gamma-gamma cascade measurements following thermal neutron absorption in nuclei is now in operation at the Livermore 1-megawatt pool-type reactor. Design features of the spectrometer and experimental techniques in its use are discussed with particular emphasis on the application of the recently introduced sum-coincidence method for analysis of capture-gamma double cascades. A new technique for the determination of added neutron binding energy is presented and various types of coincidence data from appropriate experiments are illustrated.

Abstract. An inexpensive method for detection of dust-loaded high efficiency filters is described. Air flow is continuously indicated by elementary pitot tubes and plastic rotameters. Accuracy obtained is within +- 15%. Information as to construction, installation, and use is presented.

A geometrical treatment has been used to outline the theoretical properties of optical fibers which are imperfect as well as geometrically and optically perfect. Experiments have been performed to measure some to the optical properties of individual fibers and fiber bundles.

Summary of the trumpeter swan, including geographic distribution, habitats for breeding and wintering, life cycle, nesting, food, limiting factors, longevity, population dynamics, and human management.

This bibliography contains 145 references on radiation effects on aluminum, elastomers, and lubricants. Also included are references on radiation units and conversion factors. The bibliography is limited to the period 1950 through 1959, with the references arranged alphabetically by title in five categories. An author index is provided. Sources used in compiling this bibliography are: Abstracts of Classified Reports, Bibliographies of Interest to the Atomic Energy Program: Classified and Unclassified Versions, Monthly List of Bibliographies in the Atomic Energy Program. U.S.A.E.C. Technical Information Service Extension, Nuclear Science Abstracts.

This bibliography contains 94 references on metal hydrides, with particular emphasis placed on the hydrides of titanium, yttrium, and zirconium. The bibliography covers the period 1955 through 1959. The references are arranged alphabetically by title. Sources used in compiling this bibliography are: Applied Science and Technology Index, Abstracts of Classified Reports, ASM Review of Metal Literature, Bibliographies of Interest to the Atomic Energy Program, Classified and Unclassified Parts, Industrial Arts Index, Internal Card Catalog, Monthly List of Bibliographies in the Atomic Energy Program, U.S.A.E.C. Technical Information Service Extension, Nuclear Science Abstracts.

This is a selected bibliography of books, journal articles, and unclassified reports published on the state of matter at high pressure from 1950 to October 1959. Sources consulted were: Physics Abstracts, Nuclear Science Abstracts, Geophysical Abstracts, Library of Congress Monthly Index of Russian Accessions, and Chemical Abstracts.

In a previous report the adaptation of Stix's ion-cyclotron-wave-heating scheme to the mirror geometry was suggested. An experiment along these lines has been conducted for the past year by E. Chambers, using a tubular P.I.G discharge to provide the basic plasma. The Chambers experiment has been eminently successful in demonstrating the transfer of rf power along the P.I.G. (as along a co-axial conductor), and the resultant acceleration of ions. The power transfer is evident from the predominantly resistive rf impedance of the P.I.G. (1 - 10 ohms), the production of intense luminosity outside the dc P.I.G channel when the rf is turned on, and by the observation large signals with magnetic pick-up loops. The ion heating is demonstrated by direct measurement of ion current on a probe some centimeters outside the P.I.G., and by the observation of energetic charge-exchange neutrals. At the same time, the characteristic features of heating by ion-cyclotron-waves, as described by Stix, are only partly in evidence. The visible broadening of the P.I.G. channel and such fast-ion phenomena as neutral emission do seem to be maximal near the expected cyclotron resonance point. However, the rf impedance is anomalous both in magnitude and parameter dependence, and there are …

Introduction. With the imminence of non-destructive landings of small instrumented payloads on the moon, many suggestions are being put forth as to methods of analyzing its surface. It is the purpose of this report to present a body of information which, it is hoped, will be useful in examining the feasibility of an early nuclear experiment to determine the elemental constituents of the lunar surface. The reasons for considering a nuclear approach is that it may be possible to perform an analysis without complex and elaborate manipulations, sample preparation or rigid geometrical constraints. Only those experimental designs which come within the presently-available or very-near-future general boundary conditions on weights, power, vehicles, etc., are discussed. The general approach is to consider the bombardment of the lunar surface with various nuclear beams and to examine the possible nuclear reactions which are know to be dependent on the mass and charge of the irradiated material. Then, those resultant radiations are sought which can be detected with little-or-no loss or distortion of the information which they contain.

There has been a revival of interest over the last few years in the theory of the high energy photoelectric effect. this problem has been especially clarified by the work of Pratt. Others have also contributed as will be noted below. In particular these workers have shown that the formula for photoelectric absorption of hard gamma rays by the two K electrons of an atom, which is often quoted in the literature, is too large for heavy elements by a factor amounting to approximately 2 for Pb. It turns out that the error is due to a faulty procedure described in the reference (3), p. 396 for obtaining an estimate of the exact formula.

Abstract. A conventional time-to-height converter operates by charging a capacitor to a voltage proportional to a time interval. To convert short time periods, the circuitry is limited by the stray capacities. A system was designed in which the Vernier chronotron principle is utilized to time scale the input time before time-to-height conversion. Accuracy is also improved over that attainable with conventional systems. The use of transistors is facilitated by the system design.

When light propagates with the wave normal in the direction of an optic axis of a biaxial crystal, the usual ray theory breaks down. This phenomenon can be analyzed by means of an asymptotic solution of Maxwell's equations. The intensity is governed by a partial differential equation within the phase surfaces, instead of ordinary differential equations along rays. This example slows that light does not always propagate along rays. A similar phenomenon occurs in hydromagnetics.

aluminum has been considered as a material for cladding fuel elements to be used in reactors cooled by high-temperature recirculating water. Aluminum is abundant, chap, has a relatively low cross section for thermal neutrons, and is readily fabricated into complex shapes. For these reasons, it appears that the use of aluminum rather than steel, Zircaloy or other candidate materials for fuel element cladding, would result in considerable savings in operating expense. The actual economics will of course depend on specific factors such as core materials and design of the reactor/. Aluminum appears particularly attractive for cladding the cores of aluminum-plutonium alloy proposed for the Plutonium Recycle Test Reactor since, in this case, the physical characteristics of the core and cladding would be practically identical.

The primary purpose of a cleanup system in a recirculating water loop is to maintain the best possible water quality conditions. This is normally accomplished by continuously purifying all or a portion of the coolant. A secondary objective of the cleanup system is to help maintain the system pH at a constant value. A system that will satisfactorily accomplish both of these objectives is at times difficult to obtain. Generally the pH control characteristics are sacrificed in favor of the more important cleanup requirements. A somewhat new approach to the problem pf cleanup system design appears to offer a solution to this problem for high pH systems.

Calcination of liquid radioactive wastes, the process of converting metal nitrates and sulfates to oxides by heat, is under development at Hanford as a means of reducing these liquids to a dry powder or solid which can be stored safely. Radiant-heat spray calcination, one of the methods under study, was first investigated at the Oak Ridge K-25 Plant (1) as a possible method of calcining uranyl nitrate to uranium trioxide. The process has also been under extensive development at the Pulp and Paper Research Institute of Canada (2) and is designated by them as the Atomized Suspension Technique.

Limitations on the service life of a fuel element imposed by degradation of the fissile core during irradiation have been a matter of great concern. Limitations imposed by changes in cladding properties during irradiation should be evaluated with equal care. Zircaloy-2, stainless steel, and aluminum alloys have been irradiated in the form of cladding on metallic and ceramic fuel elements. Several aspects of fuel behavior as influenced by these clad materials will be discussed. All observations related to irradiation behavior in this paper have been made on fuel specimens irradiated in water coolant.

In the past several years the use of neutron monitors for Pu concentration monitoring has been expanded in the Chemical Processing Department. Most of these monitors have been quite successful, and considerable effort is being made to improve the operation of both existing and future monitoring systems. One of the major improvements has been the development and use of a transistorized pre-amplifier or impedance matching circuits. This unit solves several problems associated with the use of boron trifluoride (BF3) neutron detectors in process monitoring; e.g., vacuum tube pre-amp failure because heat is not being conducted away.

The large scale application of Zircaloy-2 pressure tubes for structural use either in or out of reactor service, is without precedent. For more common materials, there normally are adequate data and long operating histories on which to base design and service limits. In the absence of such information for Zr-2, several investigative programs have been devised to provide much of the information from which design and service limits may be defined for Zr-2 pressure tubes. These investigations encompass in-and-out-of-reactor creep and stress-rupture testing, pre-and-post irradiation testing, and bust strength, as well as the effect of flaws or defects (from both fabrication and service origins) on burst strength and fracture characteristics. Already creep and stress rupture testing of unirradiated Zircaloy-2 is well advanced, and some experimental pre-irradiation burst testing has been carried out and will be extended rapidly as improved equipment becomes available. One irradiated KER tube sample has been burst tested and the requirement for post irradiation burst testing equipment have been defined.

The majority of two-phase flow problems involving equations of state are solved by use of point-wise utilization steam table values. In this manner, problems involving the use of the various flow equations of continuity, momentum and energy are generally forced into iterative solutions. Considerable effort towards the development of an analytical expression for the state equation seems indicated so as to simplify the analysis of two-phase problems, particularly the transient cases. The question of instability of state and mixture condition is particularly apparent in the analysis of systems undergoing phase transformation as demonstrated by the significant difference between simple theory and experimental critical flow determinations. The assumption of homogeneous, equilibrium mixtures is indicated as a first attack upon the problem.