Report presenting an investigation to determine the effect of lowering the wing from the top of the fuselage to the bottom of the fuselage on the longitudinal characteristics of a wing-fuselage and wing-fuselage-tail combination with the horizontal tail at various heights above the plane of the wing. Testing occurred at a range of Mach and Reynolds numbers.

Pressure distributions were measured over rectangular wings of aspect ratio 2 and triangular wings of aspect ratios 2 and 4 at Mach numbers of 1.45 and 1.97. The investigation includes some comparison of the effects of Reynolds number and of thickening the wing root sections on the loading.

Report presenting an investigation of stores on the Douglas D-558-II research airplane in the wind tunnel and in flight using various store configurations. The drag measured for all store configurations was high, from two to three times the free-air drag estimated for the store and pylon. Results regarding longitudinal characteristics and lateral characteristics are provided.

Report presenting an investigation of combustion oscillations using white fuming nitric acid and a hydrocarbon fuel in a 1000-pound-thrust rocket engine. Results regarding rotary oscillation shown by 40,000-frame-per-second photographs, oscillations recorded by streak photography, ion gap traces, pressure measurements, and plastic chamber erosion are provided.

Memorandum presenting an analysis to determine the compressor pressure ratios and specific weight flows obtainable with single-stage air-cooled turbines for both nonafterburning and afterburning turbojet engines operating at a flight Mach number of 2 in the stratosphere. Wide ranges in turbine-inlet temperature, tip speed, hub-tip radius ratio, and coolant-flow ratio were considered.

Report presenting an evaluation of the internal performance characteristics of several plug-type nozzles over a range of pressure ratios from 1.5 to 30. Results regarding isentropic plug nozzles, conical plug nozzles, the effect of throat and throat-approach section on performance, and air-flow parameter are provided.

Report presenting an investigation of air-launched ram jets using models with double-cone inlets with a design free-stream Mach number of 2.4. Drag data are presented in the form of cowl pressure drag, additive drag, internal drag, base drag, and total drag. Mass-flow ratios and ram-jet total-temperature ratios are also provided.

Report presenting an investigation of three axial-flow-compressor inlet stages with a hub-tip diameter ratio of 0.5 to determine whether high pressure ratios can be obtained by means of high turning with highly cambered subsonic types of blading and the effectiveness of radial gradients of energy addition in reducing the deceleration across the rotor tip and thus relieving the effect of high tip loading. Results regarding the overall stage performance, diffusion factor, element performance, and stage discharge flow distribution are provided.

Report presenting an analytical and experimental investigation of the effects of cooling-air impeller performance on turbojet-engine performance at 70 and 100 percent of rated engine speed. Analysis indicated that the impeller performance has little effect on engine performance at rated engine speed for the coolant flows considered. Results regarding the impeller total-pressure ratio and cooling air available with compressor bleed are provided.

Report presenting limited flight measurements made in order to investigate the effect of dynamic vibration absorbers on the structural response of a Lockheed F-80A airplane during buffeting. The results were obtained by comparison of data with and without the absorbers operating through use of electrical frequency-analysis techniques.

From Introduction: "The purpose of this paper is to present an analysis of the data for the remaining airplanes where the data were sufficient to warrant analysis. The data analyzed represent totals of 351 to 5660 hours of operations with ten types of Navy airplanes and were recorded during the period 1949 to 1953."

Preliminary results are presented from an investigation to determine the influence of afterbody geometry on the effects of a sonic propulsive jet at transonic speeds. The results presented are base pressure coefficient and afterbody pressure-drag coefficient as a function of jet pressure ratio for different values of Mach number and jet temperature. Geometric parameters investigated include boattail angle, jet-to-model diameter ratio, and jet-to-base diameter ratio.

Report presenting testing of two low-solidity transonic axial-flow-compressor rotors tested over a range of speeds up to a corrected tip speed of 1000 feet per second to determine the performance of such rotors and to provide experimental rotor blade-element data for low solidity levels. Comparisons of the hub and mean blade-element losses for the three rotors showed that the losses tended to decrease with a decrease in solidity. Results regarding rotor-inlet conditions, rotor-outlet conditions, overall performance, and stall characteristics are provided.

Report presenting an investigation to measure the effect of base bleed on the base pressure, lift, drag, and pitching moment of a 10-percent-thick blunt-base airfoil model. Small holes near the lower surface near the trailing edge into the base region were used to create base bleed. The drag was reduced as a result of the bleed holes.

From Summary: "Measurements of pressure distributions have been made over a wing midsemispan station on the 35 degree sweptback wing of the Douglas D-558-II research airplane at Mach numbers from 1.17 to 2.0. The results of the investigation indicate that, as the angle of attack increased at the higher Mach numbers, the pressure coefficient for a vacuum limited the extent to which the upper-surface pressures could expand. Consequently most of the increase in section normal-force coefficient at high angles of attack can be attributed to the increase in pressure over the lower surface."

Report presenting a discussion of the adverse effects of high compression ratio requirements for supersonic wind tunnels as well as the use of second throats for alleviating those effects. The results indicated that an auxiliary air-injector system can reduce starting and running compression ratios as compared to a conventional wind tunnel with a divergent diffuser.

Report presenting an approximate theory for predicting the rate of heat transfer to the stagnation region of blunt bodies in hypersonic flight. Attention is focused on the case where wall temperature is small compared to stagnation temperature. Experiments were conducted in the hypersonic gun tunnel to obtain a preliminary check on this theoretical prediction.

Report presenting an investigation of the low-speed static lateral stability characteristics of a complete model with a series of M- and W-wings. They were modified from a basic 45 degree swept wing and were designed to cover a range of spanwise locations of the sweep discontinuity.

From Introduction: "Numerous tests of tip controls on delta wings at transonic and low supersonic speeds have shown that such configurations provide satisfactory rolling-moment effectiveness, and that the hinge can be controlled by proper location of the hinge line (ref. 1). The purpose of the present tests is to determine the characteristics of such a configuration at Mach number of 4.04 and a Reynolds number of 5.8 X 10^6, based on the wing mean aerodynamic chord."

Report presenting an investigation at low speed in the 300 mph tunnel to determine the static aerodynamic forces and moments on a missile model during simulated launching from 25-percent-semispan and wing-tip locations of a wing-fuselage combination. Results regarding the differences in location and effects induced by the fuselage are provided.

Report presenting results of a wind-tunnel investigation to determine the effects of various free-flight rocket-model booster-adapter configurations on the aerodynamic characteristics in pitch and sideslip of a swept-wing, fighter airplane model for a Mach number of 2.01. Normal-force, lateral-force, pitching-moment, and yawing-moment coefficients of the airplane model were measured, and schileren photographs of the various configurations were obtained.

Report presenting an investigation to determine the zero-lift rolling effectiveness of all-movable sweptback horizontal tail fins mounted behind a notched delta wing at a constant angle of differential incidence of 7 degree per fin. Two models, one with a stiff wing and one with a flexible wing, were tested in free flight over a range of Mach numbers. The rolling effectiveness was about the same magnitude at subsonic and supersonic speeds for both models.

Report presenting an investigation of a configuration of a body of fineness ratio 16.9, an unswept wing of aspect ratio 3, and a taper ratio of 0.4, and incline tail surfaces who was aeropulsed continuously in pitch during free flight with and without a sustainer rocket motor operating. A range of Mach numbers from 0.8 to 2.1 was tested. Results regarding drag, normal force and pitching moment, flow conditions at the horizontal tail, buffeting and model vibrations, and cross coupling are provided.

Report presenting a flight investigation at a range of altitudes to determine the wing loads on the Convair XF-92A airplane over the lift range of the airplane at subsonic and transonic speeds. Theoretical lift-curve slope for a delta wing was calculated and compared with the flight data at a Mach number of 0.75.