Report presenting testing of a towed airplane model in the 19-foot pressure tunnel in conjunction with the development of a flutter testing technique. The model was equipped with an autopilot to keep the model flying straight and level in the tunnel while restrained only in drag. Results regarding period and cycles to damp to half amplitude, time histories, and motions of the flexible wing model are provided.

Report presenting lift, drag, and pitching-moment coefficients, lift-drag ratios, and center-of-pressure positions for four airplane-like configurations determined from tests at a range of Mach numbers and angles of attack. The wings and nose shapes were modified for each of the configurations.

The effects of inlet-air-flow distortions on the performance of the J65-B-3 turbojet engine were determined over a range of altitudes from 15,000 to 50,000 feet at a flight Mach number of 0.8. Radial inlet-air-flow distortions apparently do not affect the radial distribution of pressure after the first few compressor stages, while the circumferential inlet-air-flow distortion carried completely through the engine. For the distortions investigated, at rated exhaust-gas temperature and fixed-area exhaust-nozzle operation, the primary effect of the radial inlet-air-flow distortions was to reduce the engine air flow, and the primary effect of the circumferential distortion was to impose a temperature profile on the turbine, both resulting in reduction of thrust.

Report presenting an investigation at sea-level static conditions to determine the effects of radial discharge of cooling air from turbine rotor blades on turbine performance in two turbojet engines, one with a centrifugal compressor and the other with an axial-flow compressor. Results regarding the performance characteristics, efficiency comparisons, and some interpretation are provided.

Report presenting an investigation in the 4- by 4-foot supersonic pressure tunnel to determine the effects of body indentation on the minimum drag and maximum lift-drag ratio of a 60 degree swept-wing-body combination. A secondary goal of the tests was to determine the effect on the maximum lift-drag ratio of modifying the inboard plan form of the 60 degree swept wing. Lift, drag, and pitching-moment data are presented.

Report presenting an investigation of the longitudinal aerodynamic characteristics of a model with a 45 degree sweptback wing of aspect ratio 3 and a 45 degree sweptback cruciform tail at transonic speeds and small angles of attack by a free-fall recoverable-model technique. Results regarding lift, drag, static longitudinal stability, dynamic longitudinal stability, and loading distribution over the fuselage are provided.

Memorandum presenting an investigation of the performances of two annular diffuser designs applicable to turbojet afterburner installations to determine the effectiveness of injection and suction boundary-layer controls. Results regarding inlet measurements, flow observations, static-pressure distributions, downstream velocity distributions, and mean performance coefficients are provided.

Report presenting the results of force and moment tests at Mach numbers from 3.0 to 6.3 on bodies of revolution of fineness ratios from 5 to 10 and on flat-bottom bodies of fineness ratio 10 along with theoretical predictions for these bodies. Testing included eight cone and cone-cylinder models, six nose-cylinder models, and three flat-bottom bodies.

Report presenting measurements of the normal force and pitching moment of a rectangular tail surface at Mach 1.9 to determine the interference effects due to trailing shock waves from an axisymmetric body with a jet exiting from a sonic nozzle in the base. The data were obtained at various jet pressure ratios and locations of tail with respect to the body. Results regarding tail location, tail pitching moment, and tail-shock-wave effects on base pressure are provided.

Report presenting the total drag coefficients of 60 degree cone cylinders of fineness ratio 2.07 measured in free flight from Mach numbers of 1.5 to 8.2. Results regarding the smooth 60 degree cone cylinder, rifled models, and discontinuity lines in the shadowgraph pictures are provided.

Memorandum presenting an investigation of a series of five 75S-T6 aluminum-alloy elementary skin and spar-cap combinations with skin varying from 0.051 to 0.500 inch in thickness to determine the temperature and stress gradients resulting from the application of heat to the surface. The data are presented in the form of tables of the measured temperatures and stresses calculated from the measured strains.

Report presenting results and analysis of the longitudinal stability and control characteristics of the Douglas D-558-I airplane at a range of altitudes and Mach numbers. It was found that large and rapid changes in elevator deflection and force were required for balance at Mach numbers above 0.84 due to a sharp decrease in elevator-stabilizer effectiveness.

Report presenting pressure distributions, tuft patterns, and schileren surveys of a sweptback wing-fuselage combination in the 8-foot transonic tunnel at a range of Mach numbers and angles of attack. The wing had 45 degrees of sweepback, an aspect ratio of 4.0, a taper ratio of 0.6, and an NACA 65A006 airfoil section. Results regarding an angle of attack of 0 degrees, 4 degrees, 6 degrees, 8 degrees, 12 degrees, and 20 degrees are provided.

Report presenting tests of three types of nose shapes with a circular underslung inlet inlet located well forward of the body of revolution at a Mach number of 1.42. Total-pressure measurements and shadowgraphs of the different configurations were obtained.

Report presenting an investigation of the drag of spherically blunted conical models of fineness ratio 3 at a range of Mach and Reynolds numbers. Results of the tests showed that slightly blunted models had less drag than cones of the same fineness ratio through the Mach number range. Results regarding the total drag, wave drag, and viscous effects are provided.

Report presenting an investigation at low speed in the low-turbulence tunnel to determine the effects of variations in propeller-shank geometry and propeller-spinner-juncture configuration on the aerodynamic characteristics of an NACA 1-series cowling-spinner combination with an eight-blade dual-rotation propeller. Results regarding internal flow and external flow are provided.

Report presenting a pilot-opinion survey conducted with a conventional fighter airplane fitted with special servo devices for varying in flight the dihedral effect, static directional stability, and directional damping. Results showing the boundaries that define satisfactory and tolerable lateral oscillatory characteristics are presented.

Report presenting measurements of the position errors of angle-of-attack and sideslip detectors located on the fuselage of a 35 degree swept-wing fighter airplane over a range of Mach numbers and at lift coefficients up to the buffet boundary. Results regarding the angle of attack and sideslip are provided.

Report presenting a rocket-propelled missile model with cruciform, triangular, inline wings and tails, which has been tested through a range of Mach numbers at small wing-deflection angles. Results regarding the stability and damping, control effectiveness, and hinge moments are provided.

From Introduction: "Because of the unusual nature of this equipment, and because it is proving to be very useful for certain kinds of aerodynamic research, this report has been prepared. It contains a description of the equipment and its use to obtain aerodynamic coefficients. The imperfections in the wind-tunnel air stream and their effect on model tests are also discussed."

Pressure distributions and forces for a series of four bodies of revolution having nose-fineness ratios varying from 4 to 10 have been obtained and compared with theory for a Mach number of 3.12, a Reynolds number range of 2x10(sup)6 to 14x10(sup)6, and angles of attack from zero to 9 degrees. In general, a comparison of the experimental data with a second-order theory showed good agreement for the range of variables investigated.

Report presenting an investigation of the rolling effectiveness of spoiler and aileron aerodynamic controls on a fighter-type airplane from Mach numbers 0.6 to 1.5. No effects of mutual interference between the spoiler and aileron were detectable. Results regarding drag and the effect of gap upon spoiler performance are also provided.

From Summary: "The transonic similarity rules have been applied to the correlation of experimental data for a series of 22 rectangular wings having symmetrical NACA 63A-series sections, aspect ratios from 1/2 to 6, and thicknesses from 2 to 10 percent. The data were obtained by use of the transonic bump technique over a Mach number range from 0.40 to 1.10, corresponding to a Reynolds number range from 1.25 to 2.05 million. The results show that it is possible to correlate experimental data throughout the subsonic, transonic, and moderate supersonic regimes by using the transonic similarity parameters in forms which are consistent with the Prandtl-Glauert rule of linearized theory."

Report presenting data from an investigation of the effects of slot location and slot geometry on the flow in a square tunnel for a Mach number range up to 1.4. Calculated static-pressure and angle-of-flow distributions along the slotted boundary are presented for several slot configurations in a tunnel with two opposite walls slotted.