A technique is developed to construct bulk hydroxyapatite (HAp) with different cellular structures. The technique involves the initial synthesis of nanocrystalline hydroxyapatite powder from an aqueous solution using water-soluble compounds and then followed by spray drying into agglomerated granules. The granules were further cold pressed and sintered into bulks at elevated temperatures. The sintering behavior of the HAp granules was characterized and compared with those previously reported. Resulting from the fact that the starting HAp powders were extremely fine, a relatively low activation energy for sintering was obtained. In the present study, both porous and dense structures were produced by varying powder morphology and sintering parameters. Porous structures consisting of open cells were constructed. Sintered structures were characterized using scanning electron microscopy and x-ray tomography. In the present paper, hydroxyapatite coatings produced by magnetron sputtering on silicon and titanium substrates will also be presented. The mechanical properties of the coatings were measured using nanoindentation techniques and microstructures examined using transmission electron microscopy.

The goal of this joint LLNL-CalEnergy project is to develop a method for precipitating marketable silica from spent Salton Sea Geothermal Field (SSGF) brines. Many markets for silica exist. We have initially targeted production of silica as a rubber additive. Silica reinforced rubber gives tires less rolling resistance, greater tear strength, and better adhesion to steel belts. Previous silica precipitates produced by CalEnergy from Salton Sea brines were not suitable as rubber additives. They did not to disperse well in the rubber precursors and produced inferior rubber. CalEnergy currently minimizes silica scaling in some of their production facilities by acidifying the brine pH. The rate of silica precipitation slows down as the pH is lowered, so that energy extraction and brine reinfection are possible without unacceptable amounts of scaling even with more than 700 ppm SiO{sub 2} in solution. We are adding a step in which a small amount of base is added to the acidified brine to precipitate silica before reinfection. By carefully controlling the type, rate, and amount of base addition, we can optimize the properties of the precipitate to approach those of an ideal rubber additive.

X-ray backlighting is a powerful tool for diagnosing a large variety of high-energy-density phenomena. Traditional area backlighting techniques used at Nova and Omega cannot be extended efficiently to NIF-scale. New, more efficient backlighting sources and techniques are required and have begun to show promising results. These include a backlit-pinhole point projection technique, pinhole and slit arrays, distributed polychromatic sources, and picket fence backlighters. In parallel, there have been developments in improving the data SNR and hence quality by switching from film to CCD-based recording media and by removing the fixed-pattern noise of MCP-based cameras.

Plate impact experiments were performed on B270 glass in order to measure the properties of post-failure wave material. The initial failure wave velocity is 1.27 km/s . After the material is released, the failure wave velocity drops to 0.65 km/s. At a stress of 6.72 GPa, the sound speed in the failed material is 4.97 km/s (compare to 5.79 km/s in the intact material) with a density comparable to the predicted shock value. At a stress of 0.26 GPa, the average sound speed in the failed material is 3.55 km/s, and the density drops to 65% of the intact value. The spall strength of the failed material is greater than 0.14 GPa.

The saturation of impurity-rich accessory phases in a Ce-analog baseline ceramic formulation for the immobilization of excess plutonium has been tested by synthesizing an impurity-rich baseline compositions at 1300 C, 1350 C, and 1400 C in air. Impurity oxides are added at the 10 wt% level. The resulting phases assemblages are typically rich in pyrochlore, Hf-zirconolite (hafnolite), brannerite and rutile, but in many instances also contain an accessory mineral enriched in the impurity oxide. The concentration of that oxide in coexisting pyrochlore sets the saturation limit for solid solution of the component in question. In most cases, the accessory phase does not contain significant amounts of Ce, Gd or U. Exceptions are the stabilization of a Ca-lanthanide phosphate and a phosphate glass when P{sub 2}O{sub 5} is added to the formulation. P{sub 2}O{sub 5} addition is also very effective in reducing the modal amount of pyrochlore in the form relative to brannerite. Addition of the sodium-aluminosilicate, NaAlSiO{sub 4}, also results in the formation of a grain boundary melt at run conditions, but the fate of this phase on cooling is not well determined. At temperatures above 1300 C, addition of 10 wt% Fe{sub 2}O{sub 3} also leads to melting. Substitution …

Three compositions representing plutonium-free analogs of a proposed Ca-Ti-Gd-Hf-U-PU oxide ceramic for the immobilization of plutonium were equilibrated at 1 atm, 1350 C over a range of oxygen fugacities between air and that equivalent to the iron-wuestite buffer. The cerium analog replaces Pu on a mole-per-mole basic with Ce; the thorium analog replaces Pu with Th. A third material has 10 wt% Al{sub 2}O{sub 3} added to the cerium analog to encourage the formation of a Hf-analog of, CaHfTi{sub 2}O{sub 7}, zirconolite, which is referred to as hafnolite. The predominant phase produced in each formulation under all conditions is pyrochlore, A{sub 2}T{sub 2}O{sub 7}, where the T site is filled by Ti, and Ca, the lanthanides, Hf, U and Pu are accommodated on the A-site. Other lanthanide and uranium-bearing phases encountered include brannerite (UTi{sub 2}O{sub 6}), hafnolite (CaHfTi{sub 2}O{sub 7}), perovskite (CaTiO{sub 3}) and a calcium-lanthanide aluminotitanate with nominal stoichiometry (Ca,Ln)Ti{sub 2}Al{sub 9}O{sub 19}, where Ln is a lanthanide. The phase compositions show progressive shifts with decreasing oxygen fugacity. All of the phases observed have previously been identified in titanate-based high-level radioactive waste ceramics and demonstrate the flexibility of these ceramics to variations in processing parameters. The main variation is …

The initial goal of this project was to study the in-medium nucleon-nucleon interaction by testing the fundamental theory of nuclear structure, the shell model, for nuclei between {sup 8}Zr and {sup 100}Sn. The shell model predicts that nuclei with ''magic'' (2,8,20,28,40,50, and 82) numbers of protons or neutrons form closed shells in the same fashion as noble gas atoms [may49]. A ''doubly magic'' nucleus with a closed shell of both protons and neutrons has an extremely simple structure and is therefore ideal for studying the nucleon-nucleon interaction. The shell model predicts that doubly magic nuclei will be spherical and that they will have large first-excited-state energies ({approx} 1 to 3 MeV). Although the first four doubly-magic nuclei exhibit this behavior, the N = Z = 40 nucleus, {sup 80}Zr, has a very low first-excited-state energy (290 keV) and appears to be highly deformed. This breakdown is attributed to the small size of the shell gap at N = Z = 40. If this description is accurate, then the N = Z = 50 doubly magic nucleus, {sup 100}Sn, will exhibit ''normal'' closed-shell behavior. The unique insight provided by doubly-magic nuclei from {sup 80}Zr to {sup 100}Sn has made them the …

This work studies multiscale phenomena in silicon micro-resonators which comprise the mechanical components of next-generation Micro-Electro-Mechanical Systems (MEMS). Unlike their larger relatives, the behavior of these sub-micron MEMS is not described well by conventional continuum models and finite elements, but it is determined appreciably by the interplay between physics at the Angstrom, nanometer and micron scales. As device sizes are reduced below the micron scale, atomistic processes cause systematic deviations from the behavior predicted by conventional continuum elastic theory. [1] These processes cause anomalous surface effects in the resonator frequency and quality factor--even for single crystal devices with clean surfaces due to thermal fluctuations. They also lead to unconventional failure mechanisms. The simulation of these atomistic effects is a challenging problem due to the large number of atoms involved and due to the fact that they are finite temperature phenomena. Our simulations include up to two million atoms in the device itself, and hundreds of millions more are in the proximal regions of the substrate. A direct, atomistic simulation of the motion of this many atoms is prohibitive, and it would be inefficient. The micronscale processes in the substrate are well-described by finite elements, and an atomistic simulation is not …

The Pacific Northwest National Laboratory operates a number of research and development facilities for the U.S. Department of Energy in the Hanford Site's 300 Area. Process wastewater from these facilities is sent to and treated by the 300 Area Treated Effluent Disposal Facility before being discharged to the Columbia River. This report provides facility-specific information, wastewater characteristics, and describes the controls used to ensure compliance with the TEDF Waste Acceptance Criteria Program.

The use of liquid walls for fusion reactors could help solve problems associated with material erosion from high plasma heat-loads and neutronic activation of structures. A key issue analyzed here is the influx of impurity ions to the core plasma from the vapor of liquid side-walls. Numerical 2D transport simulations are performed for a slab geometry which approximates the edge region of a reactor-size tokamak. Both lithium vapor (from Li or SnLi walls) and fluorine vapor (from Flibe walls) are considered for hydrogen edge-plasmas in the high- and low-recycling regimes. It is found that the minimum influx is from lithium with a low-recycling hydrogen plasma, and the maximum influx occurs for fluorine with a high-recycling hydrogen plasma.

Electrical conductivities of fluid oxygen were measured between 30 and 80 GPa at a few 1000 K. These conditions were achieved with a reverberating shock wave technique. The measured conductivities were several orders of magnitude lower than measured previously on the single shock Hugoniot because of lower temperatures achieved under shock reverberation. Extrapolation of these data suggests that the minimum metallic conductivity of a metal will be reached near 100 GPa.

An all solid-state kicker pulser for a high current induction accelerator (the Dual-Axis Radiographic Hydrodynamic Test facility DARHT-2) has been designed and fabricated. This kicker pulser uses multiple solid state modulators stacked in an inductive-adder configuration. Each modulator is comprised of multiple metal-oxide-semiconductor field-effect transistors (MOSFETs) which quickly switch the energy storage capacitors across a magnetic induction core. Metglas is used as the core material to minimize loss. Voltage from each modulator is inductively added by a voltage summing stalk and delivered to a 50 ohm output cable. A lumped element circuit model of the inductive adder has been developed to optimize the performance of the pulser. Results for several stalk geometries will be compared with experimental data.

We developed the Scaled Thermal Explosion Experiment (STEX) to provide a database of reaction violence from thermal explosion of explosives of interest. A cylinder of explosive, 1, 2 or 4 inches in diameter, is confined in a steel cylinder with heavy end caps, and heated under controlled conditions until it explodes. Reaction violence is quantified by micropower radar measurement of the cylinder wall velocity, and by strain gauge data at reaction onset. Here we describe the test concept and design, show that the conditions are well understood, and present initial data with HMX-based explosives. The HMX results show that an explosive with high binder content yields less-violent reactions that an explosive with low binder content, and that the HMX phase at the time of explosion plays a key role in reaction violence.

During the December 1999 startup of antiproton stacking, a quick measurement of the Debuncher momentum aperture was made. The measurement was done by turning off and de-tuning the Debuncher bunch rotation cavities and observing the Debuncher 75 MHz longitudinal schottky signal of the circulating antiprotons as shown in Figure 1. The frequency at the center of the plot corresponds to the rotation frequency of the Debuncher RF cavities. (The schottky signal and the bunch rotation frequency occur at the 127th and 90th harmonics of the revolution frequency, respectively.) Figure 1 shows that the Debuncher bunch rotation energy is offset from the middle of the Debuncher momentum aperture by about 0.7% (57 MeV). The measured value of momentum aperture using the width of the base of the signal shown in Figure 1 ({eta} = 0.006 ) is 3.9% (346 MeV). This is close to the design value of 4%, so the offset is probably not due to any asymmetric momentum aperture restrictions.

This plan includes the sampling, analysis, and quality assurance requirements for the 100-BC-5 Operable Unit on the USDOE Hanford Site.

Pacific Northwest National Laboratory was awarded ten Environmental Management Science Program (EMSP) research grants in fiscal year 1996, six in fiscal year 1997, eight in fiscal year 1998 and seven in fiscal year 1999.(a) All of the fiscal year 1996 awards have been completed and the Principal Investigators are writing final reports, so their summaries will not be included in this document. This section summarizes how each of the currently funded grants addresses significant U.S. Department of Energy (DOE) cleanup issues, including those at the Hanford Site. The technical progress made to date in each of these research projects is addressed in more detail in the individual progress reports contained in this document. This research performed at PNNL is focused primarily in four areas: Tank Waste Remediation, Decontamination and Decommissioning, Spent Nuclear Fuel and Nuclear Materials, and Soil and Groundwater Cleanup.

Pacific Northwest National Laboratory conducted a proof-of-principle test at the Fort Lewis Logistics Center to determine the feasibility of using the innovative remedial technology In Situ Redox Manipulation (ISRM) to treat groundwater contaminated with dissolved TCE. ISRM creates a permeable treatment zone in the subsurface to remediate redox-sensitive contaminants in groundwater. The permeable treatment zone is created by injecting a chemical reducing agent (sodium dithionite with pH buffers) into the aquifer through a well to chemically reduce the naturally occurring ferric iron in the sediments to ferrous iron. Once the reducing agent has been given sufficient time to react with aquifer sediments, residual chemicals and reaction products are withdrawn through the same well. Redox-sensitive contaminants such as TCE, moving in a dissolved-phase plume through the treatment zone, are destroyed. TCE is degraded via reductive dechlorination within the treatment zone to benign degradation products (acetylene, ehtylene). Analyses of sediment samples collected from post-test boreholes showed a high degree of iron reduction, which confirmed the effectiveness of the treatment zone.

By 2050, when cleanup of the Hanford Site is expected to be completed, large worldwide demands to increase the global production of animal and fish protein, food, and fiber are anticipated, despite advancements in crop breeding, genetic engineering, and other technologies. The most likely large areas for expanded irrigation in the Pacific Northwest are the undeveloped East High areas of the Columbia Basin Project and non-restricted areas within the Hanford Site in south-central Washington State. The area known as the Hanford Site has all the components that favor successful irrigated farming. Constraints to agricultural development of the Hanford Site are political and social, not economic or technical. Obtaining adequate water rights for any irrigated development will be a major issue. Numerous anticipated future advances in irrigation and resource conservation techniques such as precision agriculture techniques, improved irrigation systems, and irrigation system controls will greatly minimize the negative environmental impacts of agricultural activities.

This plan includes the sampling, analysis, and quality assurance requirements for the 100-FR-3 Operable Unit on the USDOE Hanford Site.

The Energy Policy and Conservation Act (EPCA) as amended by the Energy Policy Act of 1992 (EPACT) establishes that the U.S. Department of Energy (DOE) regulate efficiency levels of certain categories of commercial heating, cooling, and water-heating equip-ment. EPACT establishes the initial minimum efficiency levels for products falling under these categories, based on ASHRAE/IES Standard 90.1-1989 requirements. EPCA states that, if ASHRAE amends Standard 90.1-1989 efficiency levels, then DOE must establish an amended uniform national manufacturing standard at the minimum level specified in the amended Standard 90.1 and that it can establish higher efficiency levels if they would result in significant additional energy savings. Standard 90.1-1999 increases minimum efficiency levels for some of the equipment categories covered by EPCA 92. DOE conducted a screening analysis to determine the energy-savings potential for EPACT-covered products meet and exceeding these levels. This paper describes the methodology, data assumptions, and results of the analysis.

This report provides particle size distribution data for samples near the Immobilized Low-Activity Waste (ILAW) Site that were archived in the Hanford Geotechnical Sample Library. Seventy-nine sediment samples were analyzed from four boreholes. Samples were collected from every ten feet in the boreholes. Eightly percent of the samples were classified as slightly gravelly sand. Fifteen percent were classified as gravelly sand, gravelly silty sand, or sandy gravels. These data indicate that the particle size of the sediment is consistent across the ILAW site and is dominated by sand in the upper part of the Hanford formation with more gravel rich units in the lower part.

This Facility Work Plan (FWP) has been prepared as required by Module VII,Section VII.M.1 of the Waste Isolation Pilot Plant (WIPP) Hazardous Waste Permit, NM4890139088-TSDF (the Permit); (NMED, 1999a). This work plan describes the programmatic facility-wide approach to future investigations at Solid Waste Management Units (SWMUs) and Areas of Concern (AOCs) specified in the Permit. This FWP addresses the current Permit requirements. It uses the results of previous investigations performed at WIPP and expands the investigations as required by the Permit. As an alternative to the Resource Conservation and Recovery Act (RCRA) Facility Investigation (RFI) specified in Module VII of the Permit, current New Mexico Environment Department (NMED) guidance identifies an Accelerated Corrective Action Approach (ACAA) that may be used for any SWMU or AOC (NMED, 1998). This accelerated approach is used to replace the standard RFI Work Plan and Report sequence with a more flexible decision-making approach. The ACAA process allows a Facility to exit the schedule of compliance contained in the Facility’s Hazardous and Solid Waste Amendments (HSWA) permit module and proceed on an accelerated time frame. Thus, the ACAA process can be entered either before or after an RFI Work Plan. According to NMED’s guidance, a facility …

The High Energy and Nuclear Physics Data Access GrandChallenge project has developed an optimizing storage access softwaresystem that was prototyped at RHIC. It is currently undergoingintegration with the STAR experiment in preparation for data taking thatstarts in mid-2000. The behavior and lessons learned in the RHIC MockData Challenge exercises are described as well as the observedperformance under conditions designed to characterize scalability. Up to250 simultaneous queries were tested and up to 10 million events across 7event components were involved in these queries. The system coordinatesthe staging of "bundles" of files from the HPSS tape system, so that allthe needed components of each event are in disk cache when accessed bythe application software. The caching policy algorithm for thecoordinated bundle staging is described in the paper. The initialprototype implementation interfaced to the Objectivity/DB. In this latestversion, it evolved to work with arbitrary files and use CORBA interfacesto the tag database and file catalog services. The interface to the tagdatabase and the MySQL-based file catalog services used by STAR aredescribed along with the planned usage scenarios.

The purpose of this calculation is to evaluate the thermal performance of the naval long spent nuclear fuel (SNF) waste package (WP) under multiple disposal conditions in a monitored geologic repository (MGR). The scope of this calculation is limited to determination of thermal temperature profiles upon the surface of, and within, the naval long SNF WP. The objective is to develop a temperature profile history within the WP, at time increments up to 10,000 years of emplacement. The results of this calculation are intended to support the Naval SNF WP Analysis and Model Report (AMR) for Site Recommendation (SR). This calculation was performed to the specifications within its Technical Development Plan (TDP) (Ref. 8.16). This calculation is developed and documented in accordance with the AP-3.12Q/REV. 0IICN. 0 procedure, Calculations.