Work is underway at the Lawrence Livermore National Laboratory to design and build a small-scale, heavy ion recirculating induction accelerator. An essential part of this design work is the development of small nonintercepting diagnostics to measure beam current and position. This paper describes some of this work, with particular emphasis on the development of a small capacitive probe beam position monitor to resolve beam position to the 100 {mu}m level in a 6 cm diameter beam pipe. Initial measured results with an 80 keV potassium ion beam are presented.

We present experimental results of a version of the Choppertron microwave generator designed to work with the high emittance beam of the Advanced Test Accelerator (ATA). Simulations showed that a 800-A, 120 {pi} cm-mrad beam (typical of ATA), could produce 800 MW of rf (11.4 GHz) power using two 12-cell, traveling-wave output structures. Funding contraints prevented final tuning of the modulator system and limited the experiment to 530 MW in narrow pulses. Over 400 MW were extracted from a single output structure through fundamental waveguide. Beam breakup was successfully suppressed with >800 amperes transported through the extraction section.

In a heavy-ion driven, inertial confinement fusion power plant, a space-charge dominated beam of heavy ions must be transported through a reactor chamber and focused on a 2-3 mm spot at the target. The spot size at the target is determined by the beam emittance and space charge, plus chromatic aberrations in the focusing lens system and errors in aiming the beam. The gain of the ICF capsule depends on the focal spot size. We are investigating low density, nearly-ballistic transport using an electromagnetic, r-z particle-in-cell code. Even at low density (n {approx} 5 {times} 10{sup 13} cm{sup {minus}3}), beam stripping may be important. To offset the effects of stripping and reduce the space charge, the beam is partially charge neutralized via a pre-formed plasma near the chamber entrance. Additional electrons for charge neutralization come from ionization of the background gas by the beam. Simulations have shown that stripping can greatly increase the spot size; however, partial neutralization can offset most of this increase.

Diamond switches are well suited for use in high temperature electronics. Laboratory feasibility of diamond switching at 1 kV and 18 A was demonstrated. DC blocking voltages up to 1 kV were demonstrated. A 50 {Omega} load line was switched using a diamond switch, with switch on-state resistivity {approx}7 {Omega}-cm. An electron beam, {approx}150 keV energy, {approx}2 {mu}s full width at half maximum was used to control the 5 mm x 5 mm x 100 {mu}m thick diamond switch. The conduction current temporal history mimics that of the electron beam. These data were taken at room temperature.

The major problem with cavitation in pumps and hydraulic systems is that there is no effective (conventional) method for detecting or predicting its inception. The traditional method of recognizing cavitation in a pump is to declare the event occurring when the total head drops by some arbitrary value (typically 3%) in response to a pressure reduction at the pump inlet. However, the device is already seriously cavitating when this happens. What is actually needed is a practical method to detect impending rather than incipient cavitation. Whereas the detection of incipient cavitation requires the detection of features just after cavitation starts, the anticipation of cavitation requires the detection and identification of precursor features just before it begins. Two recent advances that make this detection possible. The first is acoustic sensors with a bandwidth of 1 MHz and a dynamic range of 80 dB that preserve the fine details of the features when subjected to coarse vibrations. The second is the application of Bayesian parameter estimation which makes it possible to separate weak signals, such as those present in cavitation precursors, from strong signals, such as pump vibration. Bayesian parameter estimation derives a model based on cavitation hydrodynamics and produces a figure …

The floor of a black liquor recovey boiler at a mill in central Canada has experienced cracking and delamination of the composite tubing near the spout wall and deformation of the floor panels that is most severe in the vicinity of the spout wall. One possible explanation for the observed damage is impacts of salt cake falling from the convective section onto the floor. In order to determine if such impacts do occur, strain gauges and thermocouples were installed on the boiler floor in areas where cracking and deformation were most frequent. The data obtained from these instruments indicate that brief, sudden temperature fluctuations do occur, and changes in the strain experienced by the affected tube occur simultaneously. These fluctuations appear to occur less often along the spout wall and more frequently with increasing distance from the wall. The frequency of these temperature fluctuations is insufficient for thermal fatigue to be the sole cause of the cracking observed on the tubes, but the data are consistent with what might be expected from pieces of falling salt cake.

The intermetallic-based alloys for high-temperature applications are introduced. General characteristics of intermetallics are followed by identification of nickel and iron aluminides as the most practical alloys for commercial applications. An overview of the alloy compositions, melting processes, and mechanical properties for nickel and iron aluminizes are presented. The current applications and commercial producers of nickel and iron aluminizes are given. A brief description of the future prospects of intermetallic-based alloys is also given.

The largest problem facing the Department of Energy's Office of Environmental Management (EM) is the cleanup of the Cold War legacy nuclear production plants that were built and operated from the mid-forties through the late eighties. EM is now responsible for the remediation of no less than 353 projects at 53 sites across the country at, an estimated cost of $147 billion over the next 72 years. One of the keys to accomplishing a thorough cleanup of any site is a rigorous but quick contaminant characterization capability. If the contaminants present in a facility can be mapped accurately, the cleanup can proceed with surgical precision, using appropriate techniques for each contaminant type and location. The three dimensional, integrated characterization and archival system (3D-ICAS) was developed for the purpose of rapid, field level identification, mapping, and archiving of contaminant data. The system consists of three subsystems, an integrated work and operating station, a 3-D coherent laser radar, and a contaminant analysis unit. Target contaminants that can be identified include chemical (currently organic only), radiological, and base materials (asbestos). In operation, two steps are required. First, the remotely operable 3-D laser radar maps an area of interest in the spatial domain. Second, …

The Robotics Technology Development Program now known as the Robotics Crosscut Program, funded the development and deployment of a small remotely operated vehicle for inspection and cleanout of small horizontal waste storage tanks that have limited access. Besides the advantage of access through tank risers as small as 18-in. diameter, the small robotic system is also significantly less expensive to procure and to operate than larger remotely operated vehicle (ROV) systems. The vehicle specified to support this activity was the ROV Technologies, Inc., Scarab. The Scarab is a tracked vehicle with an independently actuated front and rear ''toe'' degree-of-freedom which allows the stand-off and angle of the vehicle platform with respect to the floor to be changed. The Scarab is a flexible remote tool that can be used for a variety of tasks with its primary uses targeted for inspection and small scale waste retrieval. The vehicle and any necessary process equipment are mounted in a deployment and containment enclosure to simplify deployment and movement of the system from tank to tank. This paper outlines the technical issues related to the Scarab vehicle and its deployment for use in tank inspection and waste retrieval operation

Discharge - charge cycling of thin-film rechargeable lithium batteries with an amorphous or nanocrystalline LiXMn2.Y04 cathode reveals evidence for a true hysteresis in the lithium insertion reaction. This is compared with an apparent hysteresis attributed to a kinetically hindered phase transition near 3 V for batteries with either a crystalline or a nanocrystalline LiJ@Yo4 cathode.

Composites that consist of a dielectric host containing a particulate conductor as a second phase are of interest for electrical switching applications. Such composites are "smart" materials that can function as either voltage or current limiters, and the difference in fimction depends largely upon whether the dielectric is filled to below or above the percolation threshold. It also is possible to combine current and voltage limiting in a single composite to make a "super-smart" material.

The Beamlet laser is a single-aperture prototype for the National Ignition Facility (NIF). We have recently installed and activated a 55 m{sup 3} vacuum vessel and associated diagnostic package at the output of the Beamlet that we are using to characterize target plane irradiance at high power. Measurements obtained both with and without a kinoform diffractive optic are reported. Dependences on critical laser parameters including output power, spatial filtering, and wavefront correction are discussed and compared with simulations.

A metrology system is being developed for in-vessel inspection of present day experimental, and next generation fusion reactors. It requires accurate measuring capability to verify sub-millimeter alignment of plasma-facing components in the reactor vessel. A metrology system capable of achieving such accuracy for next generation reactors must be compatible with the vessel environment of high gamma radiation, high vacuum, elevated temperature, and magnetic field. This environment requires that the system must be remotely deployed. A coherent, frequency modulated laser radar system that is capable of correcting for environmental vibration meets these requirements. The metrologyhiewing system consists of a compact laser transceiver optics module which is linked through fiber optics to the laser source and imaging units, that are located outside of the harsh environment. The deployment mechanism configured for a next generation reactor was telescopic-mast positioning system. This paper identifies the requirements for the metrology/viewing system having precision ranging and surface mapping capability, and discusses the results of various environmental tests.

Metaphorically, a teleoperator with master controllers projects the user's arms and hands into a re- mote area, Therefore, human users interact with teleoperators at a more fundamental level than they do with most human-machine systems. Instead of inputting decisions about how the system should func- tion, teleoperator users input the movements they might make if they were truly in the remote area and the remote machine must recreate their trajectories and impedance. This intense human-machine inter- action requires displays and controls more carefully attuned to human motor capabilities than is neces- sary with most systems. It is important for teleoperated manipulators to be able to recreate human trajectories and impedance in real time. One method for assessing manipulator performance is to observe how well a system be- haves while a human user completes human dexterity tasks with it. Fitts' tapping task has been, used many times in the past for this purpose. This report describes such a performance assessment. The International Submarine Engineering (ISE) Autonomous/Teleoperated Operations Manipulator (ATOM) servomanipulator system was evalu- ated using a generic positioning accuracy task. The task is a simple one but has the merits of (1) pro- ducing a performance function estimate rather than a …

Rotorcraft structures do not readily lend themselves to quantifiable inspection methods due to airframe construction techniques. Periodic visual inspections are a common practice for detecting corrosion. Unfortunately, when the telltale signs of corrosion appear visually, extensive repair or refurbishment is required. There is a need to nondestructively evaluate airframe structures in order to recognize and quantify corrosion before visual indications are present. Nondestructive evaluations of rotorcraft airframes face inherent problems different from those of the fixed wing industry. Most rotorcraft lap joints are very narrow, contain raised fastener heads, may possess distortion, and consist of thinner gage materials ({approximately}0.012--0.125 inches). In addition the structures involve stack-ups of two and three layers of thin gage skins that are separated by sealant of varying thickness. Industry lacks the necessary data techniques, and experience to adequately perform routine corrosion inspection of rotorcraft. In order to address these problems, a program is currently underway to validate the use of eddy current inspection on specific rotorcraft lap joints. Probability of detection (POD) specimens have been produced that simulate two lap joint configurations on a model TH-57/206 helicopter. The FAA's Airworthiness Assurance Center (AANC) at Sandia Labs and Bell Helicopter have applied single and dual frequency …

Oak Ridge National Laboratory (ORNL) is developing a core DNA sequencing facility to support biological research endeavors at ORNL and to conduct basic sequencing automation research. This facility is novel because its development is based on existing standard biology laboratory equipment; thus, the development process is of interest to the many small laboratories trying to use automation to control costs and increase throughput. Before automation, biology Laboratory personnel purified DNA, completed cycle sequencing, and prepared 96-well sample plates with commercially available hardware designed specifically for each step in the process. Following purification and thermal cycling, an automated sequencing machine was used for the sequencing. A technician handled all movement of the 96-well sample plates between machines. To automate the process, ORNL is adding a CRS Robotics A- 465 arm, ABI 377 sequencing machine, automated centrifuge, automated refrigerator, and possibly an automated SpeedVac. The entire system will be integrated with one central controller that will direct each machine and the robot. The goal of this system is to completely automate the sequencing procedure from bacterial cell samples through ready-to-be-sequenced DNA and ultimately to completed sequence. The system will be flexible and will accommodate different chemistries than existing automated sequencing lines. The …

To optimally design circuits for operation at high intensities of ionizing radiation, and to accurately predict their a behavior under radiation, precise device models are needed that include both stationary and dynamic effects of such radiation. Depending on the type and intensity of the ionizing radiation, different degradation mechanisms, such as photoelectric effect, total dose effect, or single even upset might be dominant. In this paper, the authors consider the photoelectric effect associated with the generation of electron-hole pairs in the semiconductor. The effects of low radiation intensity on p-II diodes and bipolar junction transistors (BJTs) were described by low-injection theory in the classical paper by Wirth and Rogers. However, in BJTs compatible with modem integrated circuit technology, high-resistivity regions are often used to enhance device performance, either as a substrate or as an epitaxial layer such as the low-doped n-type collector region of the device. Using low-injection theory, the transient response of epitaxial BJTs was discussed by Florian et al., who mainly concentrated on the effects of the Hi-Lo (high doping - low doping) epilayer/substrate junction of the collector, and on geometrical effects of realistic devices. For devices with highly resistive regions, the assumption of low-level injection is often …

The performance capabilities of Npn and Pnp AlGaN/GaN heterojunction bipolar transistors have been investigated by using a drift-diffusion transport model. Numerical results have been employed to study the effect of the p-type Mg doping and its incomplete ionization on device performance. The high base resistance induced by the deep acceptor level is found to be the cause of limited current gain values for Npn devices. Several computation approaches have been considered to improve their performance. Reasonable improvement of the DC current gain {beta} is observed by realistically reducing the base thickness in accordance with processing limitations. Base transport enhancement is also predicted by the introduction of a quasi-electric field in the base. The impact of the base resistivity on high-frequency characteristics is investigated for Npn AlGaN/GaN devices. Optimized predictions with maximum oscillation frequency value as high as f{sub MAX} = 20 GHz and a unilateral power gain--U = 25 dB make this bipolar GaN-based technology compatible with communication applications. Simulation results reveal that the restricted amount of free carriers from the p-doped emitter limits Pnp's DC performances operating in common emitter configuration. A preliminary analysis of r.f. characteristics for the Pnp counterpart indicates limited performance mainly caused by the degraded …

Lifetime studies in four-point flexure were performed on a Hi-Nicalon^TM fiber-reinforced SiC matrix composite over a temperature range of 700 degrees to 1150 degrees C in air. The composite consisted of ~40 vol. % Hi-Nicalon^TM fiber (8-harness weave) with a 0.5 Mu-m BN fiber coating and a melt-infiltration SiC matrix wand was tested with as-machined surfaces. Lifetime results indicated that the composite exhibited a stress-dependent lifetime at stress levels above an apparent fatigue limit, similar to the trend observed in CG-Nicalon^TM fiber reinforced CVI SiC matrix composites. At less than or equal to 950 degrees C, the lifetimes of Hi-Nicalon/MI SiC composites decreased with increasing applied stress level and test temperature. However, the lifetimes were extended as test temperature increased from 950 degees to 1150 degrees C as a result of surface crack sealing due to glass formation by the oxidation of Mi SiC matrix. The lifetime governing processes were, in general, attributed to the progressive oxidation of BN fiber coating and formation of glassy phase, which formed a strong bond between fiber and matrix, resulting in embrittlement of the composite with time.

The authors derive an equation determining the small-x evolution of the F{sub 2} structure function of a large nucleus which resumes a cascade of gluons in the leading logarithmic approximation using Mueller's color dipole model. In the traditional language it corresponds to resummation of the pomeron fan diagrams, originally conjectured in the GLR equation. The authors show that the solution of the equation describes the physics of structure functions at high partonic densities, thus allowing them to gain some understanding of the most interesting and challenging phenomena in small-x physics--saturation.

This paper examines the modeling accuracy of finite element interpolation, kriging, and polynomial regression used in conjunction with the Progressive Lattice Sampling (PLS) incremental design-of-experiments approach. PLS is a paradigm for sampling a deterministic hypercubic parameter space by placing and incrementally adding samples in a manner intended to maximally reduce lack of knowledge in the parameter space. When combined with suitable interpolation methods, PLS is a formulation for progressive construction of response surface approximations (RSA) in which the RSA are efficiently upgradable, and upon upgrading, offer convergence information essential in estimating error introduced by the use of RSA in the problem. The three interpolation methods tried here are examined for performance in replicating an analytic test function as measured by several different indicators. The process described here provides a framework for future studies using other interpolation schemes, test functions, and measures of approximation quality.

We detail the design and development of a miniature thermal cycling instrument for performing the polymerase chain reaction (PCR) that uses microfabricated, silicon-based reaction chambers. The MEMS-based, battery-operated instrument shows significant improvements over commercial thermal cycling instrumentation. Several different biological systems have been amplified and verified with the miniature PCR instrument including the Human Immunodeficiency Virus; both cloned and genomic DNA templates of {beta} globin; and the genetic disease, Cystic Fibrosis from human DNA. The miniaturization of a PCR thermal cycler is the initial module of a fully-integrated portable, low-power, rapid, and highly efficient bioanalytical instrument.

The risks associated with the transport of spent nuclear fuel by truck and rail have been reexamined and compared to results published in NUREG-O170 and the Modal Study. The full reexamination considered transport of PWR and BWR spent fuel by truck and rail in four generic Type B spent fuel casks. Because they are typical, this paper presents results only for transport of PWR spent fuel in steel-lead steel casks. Cask and spent fuel response to collision impacts and fires were evaluated by performing three-dimensional finite element and one-dimensional heat transport calculations. Accident release fractions were developed by critical review of literature data. Accident severity fractions were developed from Modal Study truck and rail accident event trees, modified to reflect the frequency of occurrence of hard and soft rock wayside route surfaces as determined by analysis of geographic data. Incident-free population doses and the population dose risks associated with the accidents that might occur during transport were calculated using the RADTRAN 5 transportation risk code. The calculated incident-free doses were compared to those published in NUREG-O170. The calculated accident dose risks were compared to dose risks calculated using NUREG-0170 and Modal Study accident source terms. The comparisons demonstrated that both …

A key issue of solder joint reliability is joint failure due to thermomechanical fatigue (TMF). TMF is caused by different coefficients of thermal expansion (CTEs) of the materials in an electronic package, combined with changes in the ambient temperature. Different CTEs result in cyclical strain in the assembly, and this strain is concentrated almost entirely in the solder because it is the most deformable portion of the package. Since solder alloy is at a significant fraction of its melting point even at room temperature, the cyclical strain enhances mass diffusion and causes dramatic changes in the alloy microstructure over time. As the microstructure changes and becomes coarser, the solder alloy weakens and eventually microcracks nucleate and grow in the joint, leading to component failure. the failure of solder joints is difficult to detect due to the inert nature of the electrical system. If the system is not on for extended periods then failures can not be observed. Therefore it is important to develop an advanced predictive capability which allows scientists and engineers to predict solder degradation and identify reliability problems in aging electronics early.