Beam gauges have been used in the last decade or so for measuring the internal azimuthal compressive coil stresses in superconducting magnets. In early model Large Hadron Collider Interaction Region (LHC IR) quadrupoles tested at Fermilab, the beam gauges indicated excessively high amounts of inner and outer coil prestress during the collaring process, inconsistent with the coil size and modulus data. In response to these measurements, a simple mechanics based quantitative understanding of different factors affecting beam gauges has been developed. A finite element model with contact elements and non-linear material behavior, confirmed with experimental results, was developed. The results indicate that a small plastic deformation of either the beam or the backing plate can cause significant errors in the measured stress values. The effect of variations in coil modulus and support boundary conditions on beam gauge performance are also discussed.

None

Thin films of complex perovskites have a number of potentially important applications. Of major scientific and practical concern is the scaling of properties as film dimensions are reduced. This paper describes a satisfactory relationship between bulk and thin film dielectric properties of (Ba,Sr)TiO{sub 3}. Relative contributions of strain, A:B cation stoichiometry, and interface are separated to explain temperature dependent dielectric behavior.

Comparative experiments using high energy (10 MeV) electrons and test reactor neutrons have been undertaken to understand the role that primary damage state has on hardening (embrittlement) induced by irradiation at 300 C. Electrons produce displacement damage primarily by low energy atomic recoils, while fast neutrons produce displacements from considerably higher energy recoils. Comparison of changes resulting from neutron irradiation, in which nascent point defect clusters can form in dense cascades, with electron irradiation, where cascade formation is minimized, can provide insight into the role that the in-cascade point defect clusters have on the mechanisms of embrittlement. Tensile property changes induced by 10 MeV electrons or test reactor neutron irradiations of unalloyed iron and an Fe-O.9 wt.% Cu-1.0 wt.% Mn alloy were examined in the damage range of 9.0 x 10{sup {minus}5} dpa to 1.5 x 10{sup {minus}2} dpa. The results show the ternary alloy experienced substantially greater embrittlement in both the electron and neutron irradiate samples relative to unalloyed iron. Despite their disparate nature of defect production similar embrittlement trends with increasing radiation damage were observed for electrons and neutrons in both the ternary and unalloyed iron.

High angular resolution electron channeling X-ray spectroscopy (HARECXS) was examined as a practical tool to locate lattice-ions in spinel crystals. The orientation dependent intensity distribution of emitted X-rays obtained by HARECXS is so sensitive to lattice-ion configuration in the illuminated areas that the occupation probabilities on specific positions in the crystal lattice can be determined accurately through comparison with the theoretical rocking curves. HARECXS measurements have revealed partially disordered cation arrangement in MgO{center_dot}nAl{sub 2}O{sub 3} with n = 1.0 and 2.4. Most Al{sup 3+} lattice-ions occupy the octahedral (VIII) sites, while Mg{sup 2} lattice-ions reside on both the tetrahedral (IV) and the octahedral (VIII) sites. The structural vacancies are enriched in the IV-sites. Further evacuation of cations from the IV-sites to the VIII-sites is recognized in a disordering process induced by irradiation with 1 MeV Ne{sup +} ions up to 8.9 dpa at 870 K.

Conventional electroactive stack components in thermal batteries are constructed from pressed-powder parts. These include the anode, separator, and cathode pellets (discs). Pressing parts that are less than 0.010 inch thick is difficult. The use of plasma spray to deposit thin CoS{sub 2} cathode films onto a stainless steel substrate was examined as an alternative to pressed-powder cathodes. The plasma-sprayed electrodes were tested in single cells under isothermal conditions and constant-current discharge over a temperature range of 400 C to 550 C using standard LiSi anodes and separators based on the LiCl-KCl eutectic. Similar tests were conducted with cells built with conventional pressed-powder cathodes, which were tested under the same conditions for comparative purposes. This paper presents the results of those tests.

A letter report issued by the General Accounting Office with an abstract that begins "Pursuant to a congressional request, GAO reviewed the Adoption and Safe Families Act of 1997 (ASFA), focusing on: (1) how states have responded to ASFA regarding legal, administrative, and other changes that social workers may need to make in their day-to-day practice of handling child welfare cases; (2) the status of states' implementation of the two provisions related to making timely permanency decisions for those foster children who are unable to safely return home; and (3) the actions the Department of Health and Human Services (HHS) has taken to assist states and monitor the implementation of these two provisions."

We study the feasibility of a precise measurement of the mass of a 120 GeV MSM Higgs boson through direct reconstruction of ZH {yields} q{bar q}H events that would be achieved in a future e{sup +}e{sup -} linear collider operating at a center-of-mass energy of 500 GeV. Much effort has been put in a ''realistic simulation'' by including irreducible+reducible backgrounds, realistic detector effects and reconstruction procedures and sophisticated analysis tools involving Neural Networks and kinematical fitting. As a result, the Higgs mass is determined with a statistical accuracy of 50 MeV and the Z-Higgs Yukawa coupling measured to 0.7%, assuming 500 fb{sup -1} of integrated luminosity.

Laser modulated scattering (LMS) is introduced as a non-destructive evaluation tool for defect inspection and characterization of optical surfaces and thin film coatings. This technique is a scatter sensitive version of the well-known photothermal microscopy (PTM) technique. It allows simultaneous measurement of the DC and AC scattering signals of a probe laser beam from an optical surface. By comparison between the DC and AC scattering signals, one can differentiate absorptive defects from non-absorptive ones. This paper describes the principle of the LMS technique and the experimental setup, and illustrates examples on using LMS as a tool for nondestructive evaluation of high quality optics.

Thermal oxide and PETEOS oxide surfaces, polished on an IPEC 472 with different combinations of polish pad, slurry, and polishing conditions, were studied with ex situ atomic force microscopy. The post polish surfaces were analyzed qualitatively by visual inspection and quantitatively by spectral and scaling analyses. Spectral and scaling analyses gave consistent interpretations of morphology evolution. Polishing with either a fixed abrasive pad or alumina-based slurry occurred via a mechanism for which asperities are removed and recesses are filled. A sputtering-type mechanism may contribute to material removal when polishing with silica- or ceria-based slurries.

OAK B188 A Novel Approach to Material Development for Advanced Reactor Systems. Year one of this project had three major goals. First, to specify, order and install a new high current ion source for more rapid and stable proton irradiation. Second, to assess the use low temperature irradiation and chromium pre-enrichment in an effort to isolate a radiation damage microstructure in stainless steels without the effects of RIS. Third, to prepare for the irradiation of reactor pressure vessel steel and Zircaloy. In year 1 quarter 1, the project goal was to order the high current ion source and to procure and prepare samples of stainless steel for low temperature proton irradiation.

Metalorganic chemical vapor deposition was used to synthesize epitaxial Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}{minus}PbTiO{sub 3} films on SrTiO{sub 3} and SrRuO{sub 3}/SrTiO{sub 3} substrates, using solid Mg(DPM){sub 2} as the Mg precursor. Depositing conditions have been identified under which phase-pure perovskite PMN-PT may be grown. In contrast, in lead-poor environments, an additional second phases of a disordered magnesium-niobium oxide has tentatively been identified. X-ray diffraction and selected area electron diffraction indicate a cube-on-cube orientation relationship between film and substrate, with a (001) rocking curve width of 0.1{degree}, and in-plane mosaic of 0.8{degree}. The rms surface roughness of a 200nm thick PMN film on SrTiO{sub 3} was 2 to 3 nm as measured by scanned probe microscopy. The zero-bias dielectric constant and loss measured at room temperature and 10 kHz for a 350 nm thick pure PMN film on SrRuO{sub 3}/SrTiO{sub 3} were 1100 and 2%, respectively. Small-signal permittivity ranged from 900 to 1400 depending on deposition conditions and Ti content; low values for the dielectric loss between 1 and 3% were determined for all specimens. Here the authors report on growth conditions and the initial structural and dielectric characterization of these samples.

Over two decades since its discovery at Fermilab in 1977, the b quark has become an important laboratory for the exploration of the Standard Model as well as a potential window beyond it. Its kinematic properties, its large mass and long lifetime, and its large production cross section in hadron collisions, make it an excellent subject of study at the Tevatron {bar p}p collider. In this article, we will review recent results from CDF and D0 in two categories of tests of the Standard Model: the search for rare b decays, and the measurement of asymmetry parameters related to B{sup 0} meson mixing and CP violation. The detectors have been described elsewhere. The data for the results presented here are from the 1992-96 collider run, representing at each experiment, approximately 100 pb{sup -1} of integrated luminosity at {radical}s = 1.8 TeV.

We present the latest results from the CDF experiment at the Tevatron Collider in p{bar p} collisions at {radical}s = 1.8 TeV. The large data sample collected during Run 1, from 1992 until 1995, allows measurements in many domains of high-energy physics. Here, we report on the first measurement of sin(2{beta}), a CP violation parameter, and on an improved measurement of the top quark cross section. We also report on searches for the so-far elusive Higgs boson, and for SUSY, through searches for direct production of top and bottom scalar quarks. Finally, we outline the prospects for the physics during the upcoming Run 2, ready to start in the upcoming year 2000.

Other written product issued by the General Accounting Office with an abstract that begins "Pursuant to a legislative requirement, GAO reviewed the Securities and Exchange Commission (SEC) new rule on amending the Intermarket Trading System Plan. GAO noted that: (1) the final rule amends the plan governing the operation of the Intermarket Trading System; and (2) SEC complied with the applicable requirements in promulgating the rule."

Correspondence issued by the General Accounting Office with an abstract that begins "Pursuant to a congressional request, GAO provided information regarding work done on the Union Station Redevelopment Project by Park Woodworking, Inc., focusing on the: (1) extent of the government's liability, if any, for costs incurred for which Park was not compensated; (2) extent to which Park was not compensated for the work it did; and (3) actions taken by the Secretary of Transportation and the Department of Transportation (DOT) Inspector General (IG) in response to complaints received from Park."

None

Zirconolite is one of the major host phases for actinides in various wasteforms for immobilizing high level radioactive waste (HLW). Over time, zirconolite's crystalline matrix is damaged by {alpha}-particles and energetic recoil nuclei recoil resulting from {alpha}-decay events. The cumulative damage caused by these particles results in amorphization. Data from natural zirconolites suggest that radiation damage anneals over geologic time and is dependant on the thermal history of the material. Proposed HLW containment strategies rely on both a suitable wasteform and geologic isolation. Depending on the waste loading, depth of burial, and the repository-specific geothermal gradient, burial could result in a wasteform being exposed to temperatures of between 100--450 C. Consequently, it is important to assess the effect of temperature on radiation damage in synthetic zirconolite. Zirconolite containing wasteforms are likely to be hot pressed at or below 1,473 K (1,200 C) and/or sintered at or below 1,623 K (1,350 C). Zirconolite fabricated at temperatures below 1,523 K (1,250 C) contains many stacking faults. As there have been various attempts to link radiation resistance to structure, the authors decided it was also pertinent to assess the role of stacking faults in radiation resistance. In this study, they simulate {alpha}-decay damage …

The trilinear couplings appear as the three gauge boson vertices and can be measured by studying the gauge boson pair production processes. The measurement of the coupling parameters is one of the few remaining crucial tests of the Standard Model. D0 has studied W{gamma}, Z{gamma}, WW, and WZ production and found no evidence of anomalous production. In this paper we review all the current results from D0 data.

A letter report issued by the General Accounting Office with an abstract that begins "Pursuant to a congressional request, GAO reviewed challenges facing the Department of Health and Human Services' (HHS) Vaccine Injury Compensation Program (VICP), focusing on: (1) how long it takes to process a claim through VICP; (2) the extent to which recent changes to the program's injury table have made it easier or more difficult for petitioners to obtain compensation for vaccine-related injuries; and (3) why the trust fund continues to grow, and what budgetary effect proposed options for addressing the growing trust fund balance would have."

We measure cavity ringdown spectra of the A{sup 2}{Delta}-X{sup 2}II transition of the methylidyne (CH) radical in a series of rich low-pressure methane-oxygen-argon flames and demonstrate that the technique is sensitive, quantitative, and straightforward in its implementation and interpretation. As a line-of-sight technique, it complements imaging techniques, such as planar laser-induced fluorescence. Our results generally agree with chemical kinetic models for methane oxidation that have appeared in the literature, but suggest some refinements are necessary. Additional examination of the CH + O{sub 2} reaction rate as a function of temperature is advised. Our results are consistent with those of Derzy et al. using the C{sup 2}{Sigma}{sup +}-X{sup 2}II transition for stoichiometric, low-pressure flames which include nitrogen. Our results for rich flames, as with earlier experiments for singlet methylene, suggest that flame chemical kinetic models need to be adjusted to account for flame chemistry for stoichiometries richer than {phi} = 1.5.

Gross gamma ray logs, recorded from January 1975 through mid-year 1994 as part of the Single-Shell Tank Farm Dry Well Surveillance Program, have been reanalyzed for the S tank farm to locate the presence of mobile radionuclides in the subsurface.

In the past few years, many states have established specific regulations for the management of petroleum industry wastes containing naturally occurring radioactive material (NORM) above specified thresholds. These regulations have limited the number of disposal options available for NORM-containing wastes, thereby increasing the related waste management costs. In view of the increasing economic burden associated with NORM management, industry and regulators are interested in identifying cost-effective disposal alternatives that still provide adequate protection of human health and the environment. One such alternative being considered is the disposal of NORM-containing wastes in landfills permitted to accept only nonhazardous wastes. The disposal of petroleum industry wastes containing radium-226 and lead-210 above regulated levels in nonhazardous landfills was modeled to evaluate the potential radiological doses and associated health risks to workers and the general public. A variety of scenarios were considered to evaluate the effects associated with the operational phase (i.e., during landfill operations) and future use of the landfill property. Doses were calculated for the maximally exposed receptor for each scenario. This paper presents the results of that study and some conclusions and recommendations drawn from it.

This edition contains more information about new efforts and programs in DOE's Office of Building Technology, State and Community Programs (BTS), and highlights the evolution of a new approach to making buildings more energy-efficient, comfortable, and affordable.