Report presenting a blade-vibration and rotating-stall survey on a modified version of a production turbojet engine with a 13-stage axial-flow compressor with a design pressure ratio of 7 and an air flow of 120 pounds per second. This testing was carried out due to the problems rotating stall can cause with both experimental and production axial-flow compressors. Results regarding the rotating-stall patterns, rotor-blade vibrations, radial and axial strength of rotating stall, and maximum rotating-stall speed are provided.

Report presenting a flight test of pentaborane fuel in an air-launched ramjet engine with a design free-stream Mach number of 1.8. The ramjet used in the investigation had a revised spray bar-flameholder configuration. Results regarding propulsive thrust and propulsive-thrust specific fuel consumption are provided.

Report presenting an investigation of turbine operating temperatures as affected by liquid cooling, especially if materials of high conductivity are used, at gas temperatures up to 1925 degrees Fahrenheit. Results regarding the statio heat-transfer rig and turbine rig are provided. The investigation showed that nonstrategic material such as aluminum alloy can be used in liquid-cooled turbine wheels at high gas temperatures.

Report presenting an investigation with a ram-jet combustion chamber to determine the effect of fuel-air ratio and the inlet-air parameters of pressure, temperature, and velocity on combustion limit, combustion efficiency, and flame length.

Results of a wind-tunnel investigation at a Reynolds number of 6.8 x 10(exp 6) to determine the static longitudinal stability characteristics of a 42 degree sweptback wing and fuselage combination with a sweptback horizontal tail are provided. Included are the effects of vertical position of fuselage and tail with respect to wing for several combinations of high-lift and staff-control devices. Also included is the effect of a simulated ground.

Memorandum presenting measurements of gust and draft velocities within cumulus clouds at a certain army air field using an AT-6 airplane. The measurements were made to supplement the at a obtained with P-61C airplanes. The data are summarized in tables.

Report presenting testing of a twin-scoop duct inlet that enclosed 37.2 percent of the forebody circumference at Mach numbers between 1.36 and 2.01. The approach to each scoop consisted of a ramp that deflected the flow to create an oblique shock wave in front of the duct entrance. Results regarding the inlet proportions, ramp angle, slots, and angle of incidence are provided.

Memorandum presenting measurements of some of the high-speed characteristics of the D-558-1 airplane up to Mach number 0.89. The results of the tests showed that the stabilizer incidence drastically affected the longitudinal trim characteristics above a Mach number of 0.80.

Report presenting a discussion of a number of the problems that most frequently arise with airfoils on helicopters. A reference list of published reports on airfoil section characteristics which are useful in regards to these helicopter problems is also included.

Report presenting tank results for take-off tests with a powered dynamic model of a hypothetical jet-propelled high-speed airplane fitted with NACA hydro-skis and with flush turbojet intakes on the upper part of the fuselage near the nose. Some of the investigations included were the possibility of making take-offs without spray entering the intakes, the effect of turbojet air inflow on the tendency of spray to enter the intakes, and the effect of jet power on trim.

From Summary: "The pressure drops through electrically heated Inconel tubes with length-diameter ratios of 29.25, 58.50, 87.75, and 117.00 have been measured at entrance Mach numbers from approximately 0.12 to the value at which choking occurred. The heat-input rate was varied from zero to the highest values allowable without damaging the tubes. Experimental data and a number of computed variables are presented in tabular form."

From Summary: "Ogive-cylindrical fuselages of fineness ratio 11 have been flight-tested with and without stabilizing fins. Base-pressure measurements over a range of free-stream Mach numbers from 0.7 to 1.3 indicated that the fins reduced the base drag. A rear-support sting similar to those used in wind tunnels was tested with one of the fuselages and found to reduce base suction by 40 percent at subsonic speeds, but to have little effect at Mach numbers above 1.15."

Report presenting an investigation of the performance of several conical cooling-air ejectors at primary jet pressure ratios from 1 to 10, secondary shroud pressure ratios from 0.60 to 4.00, and primary to secondary temperature ratio of 1.0. The investigation centered on primary air flow, secondary air flow, primary nozzle thrust, and gross ejector thrust.

Report presenting testing of JP-3 fuel and a slurry of 60 percent powdered magnesium in JP-3 fuel in a small-scale afterburner in the presence of large quantities of water vapor. The results indicated that total temperature, combustion efficiency, and air specific impulse were improved when the magnesium slurry was used, but the improvements came at the cost of increased liquid consumption.

Report presenting an investigation of some effects of aileron spanwise location and wing structural rigidity on the rolling power of 0.3-chord plain, flap-type ailerons on a wing with a taper ratio of 0.25, an aspect ratio of 3.5, and swept back 63 degrees at the leading edge. Results regarding the aeroelastic effects and aileron span and spanwise location are provided.

Memorandum presenting the results of an experimental investigation to determine the effects of Reynolds number on the flow characteristics over a delta wing at a Mach number 2.41. The wing streamwise airfoil sections are based on the NACA 00-thickness series with the maximum thickness varying from 4 percent at the root section to 6.24 percent at the 90-percent spanwise station. Results regarding force data and pressure-distribution data are provided.

Report presenting an investigation of the effect of Reynolds number and the addition of leading-edge roughness on the aerodynamic characteristics of wings with aspect ratio 1, 2, and 3, a rectangular plan form, square-cut wing tips, and NACA 0012 airfoil sections. Results regarding lift and moment, lift-curve slope, and maximum lift are provided.

Report presenting longitudinal-damping data in the form of the pitching-moment derivatives and summarized from flight tests of rocket-propelled models and full-scale airplanes. 22 models and 4 airplanes are examined in the study and the damping derivative results are generalized.

"The experimental performance of a modified turbine for driving a supersonic compressor is presented and compared with the performance of the original configuration to illustrate the effect of small changes in the ratio of nozzle-throat area to rotor-throat area. Performance is based on the performance of turbines designed to operate with both blade rows close to choking. On the basis of the results of this investigation, the ratio of areas is concluded to become especially critical in the design of turbines such as those designed to drive high-speed, high-specific weight-flow compressors where the turbine nozzles and rotor are both very close to choking" (p. 1).

Report presenting the results of an investigation of flap-type controls on a low-aspect-ratio triangular wing using NACA 0005-63 sections for a constant-chord and a constant-percent-chord control surface. Two flap profiles were investigated: one with a true contour and the other with a blunt trailing edge. Results regarding lift, drag, pitching moment, hinge moment, and rolling moments were obtained for several Mach numbers, a constant Reynolds number, and a range of angles of attack.

Memorandum presenting an investigation of a 2:1 area ratio conical diffuser of length equal to the inlet diameter with separate variation of several basic parameters for simple nontwisted counterrotating rectangular vortex generators over a considerable range of inlet-boundary-layer thickness. The maximum values of static-pressure rise were determined for angle of attack, spacing, aspect ratio, and span-to-inlet boundary-layer thickness. Results for the diffuser with no vortex generators, effects of selectable vortex-generator variables, effect of inlet-boundary-layer displacement thickness, and use of the maximum indicated vortex-generator design values are provided.

Memorandum presenting flutter tests of untapered, low-aspect-ratio, sweptback-wing models and of triangular-wing models of solid magnesium, aluminum, and steel construction in an intermittent supersonic wind tunnel at Mach number 1.3. Flutter data are presented for 31 sweptback wing models and 24 triangular-wing models. The flutter boundaries are indicated on plots of streamwise thickness ratio and aspect ratio.

Memorandum presenting a method for calculating the stick-fixed longitudinal stability of a wing-fuselage configuration at subcritical Mach numbers. The method applies to unswept- and swept-wing configurations. The stability parameters estimated by the method show reasonable agreement with the experimental values for the 23 configurations used in the comparison.

Report presenting effects of wing trailing-edge bluntness on aerodynamic characteristics of a wing-body combination at a range of Mach numbers and Reynolds numbers. Modifications were made to the rear half of a basic plane tapered wing of aspect ratio 3.1 and a 3-percent-thick, circular-arc, biconvex section with three types of trailing-edge shapes. Results regarding the lift characteristics, pitching-moment characteristics, drag characteristics, and maximum lift-drag ratio are provided.