Report presenting measurements downwash angles behind a model of a high-aspect-ratio wing at points near the probable tail location at Mach numbers up to 0.89 in the high-speed tunnel. The model has an NACA 65-210 section, an aspect ratio of 9.0, a taper ratio of 2.5:1, no twist, dihedral, or sweepback. Results regarding experimental data and comparison of experimental and calculated results are provided.

Report presenting tests to determine the effect of sweepback angle and aspect ratio on the drag at supersonic speeds of wings of NACA 65-009 airfoil section. The current report is part of a bigger investigation and includes results for aspect ratios of 3.8 and 5.0. Results regarding the drag coefficient and general effect of aspect ratio are provided.

"Several dive paths were calculated for a C54 airplane starting from level flight at an altitude of 4000 feet and from an initial indicated airspeed of 200 miles per hour. The results show that, within the limits of the possible paths permitted by the evidence of the crash at Bainbridge, the speed of impact would be about 370 miles per hour and the time to crash would be between 12 1/2 and 15 1/2 seconds. Tail load calculations indicate that, with moderate negative acceleration of the airplane, the tail would fail near the end of the dive in a manner consistent in several important respects with the evidence" (p. 1).

The performance of the 11-stage axial-flow compressor, modified to improve the compressor-outlet velocity, in a revised X24C-4B turbojet engine is presented and compared with the performance of the compressor in the original engine. Performance data were obtained from an investigation of the revised engine in the MACA Cleveland altitude wind tunnel. Compressor performance data were obtained for engine operation with four exhaust nozzles of different outlet area at simulated altitudes from 15,OOO to 45,000 feet, simulated flight Mach numbers from 0.24 to 1.07, and engine speeds from 4000 to 12,500 rpm. The data cover a range of corrected engine speeds from 4100 to 13,500 rpm, which correspond to compressor Mach numbers from 0.30 to 1.00.

From Summary: "Drag measurements at transonic speeds on rectangular airfoils and on airfoils swept back 450 are reported. These airfoils, which were mounted on cylindrical test bodies, are part of a series being tested in free drops from high altitude to determine the effect of variation of basic airfoil parameters on airfoil drag characteristics at transonic speeds. These rectangular and swept-back airfoils had the same span, airfoil section (NACA 65-009), and chord perpendicular to the leading edge. The tests were made to compare the drag of rectangular and sweptback airfoils at a higher aspect ratio than had been used in a similar comparison reported previously."

Wind tunnel tests haved been made at low speed to various small-scale models of swept-back, swept-forward, and yawed wings. Tests covered changes in aspect ratio, taper ratio, and tip shape.

Tests have been conducted to determine the drive-motor torque and the static force and moment characteristics of the AN/SPS-1 radar antenna. Shifting the longitudinal position of the antenna had very little effect on the drive-motor torque, which reached a maximum value expressed in terms of dynamic pressure (T/q)(sub max) of 1.15 at an azimuth angle of 245. The maximum observed values of rolling, pitching, and yawing moments in terms of dynamic pressure are -29.0, 66.6, and 13.4, respectively.

Tests have been conducted in the Langley high-speed 7- by 10-foot tunnel over a Mach number range from 0.40 to 0.91 to determine the stability and control characteristics of an 0.08-scale model of the Chance Vought XF7U-1 airplane. The aileron characteristics of the complete model are presented in the present report with a very limited analysis of the results.

Tests of a PB2Y-3 flying boat were made at the U.S. Naval Air Station, Patuxent River, Md., to determine its hydrodynamic trim limits of stability. Corresponding tests were also made of a 1/8-size powered dynamic model of the same flying boat in Langley tank no. 1. During the tank tests, the full-size testing procedure was reproduced as closely as possible in order to obtain data for a direct correlation of the results. As a nominal gross load of 66,000 pounds, the lower trim limits of the full-size and model were in good agreement above a speed of 80 feet per second. As the speed decreased below 80 feet per second, the difference between the model trim limits and full-scale trim limits gradually became larger. The upper trim limit of the model with flaps deflected 0 deg was higher than that of the full-size, but the difference was small over the speed range compared. At flap deflections greater than 0 deg, it was not possible to trim either the model of the airplane to the upper limit with the center of gravity at 28 percent of the mean aerodynamic chord. The decrease in the lower trim limits with increase in flap …

"Data for a liquid-cooled engine with a displacement volume of 1710 cubic inches were analyzed to determine the effect of exhaust pressure on the engine cooling characteristics. The data covered a range of exhaust pressures from 7 to 62 inches of mercury absolute, inlet-manifold pressures from 30 to 50 inches of mercury absolute, engine speeds from 1600 to 3000 rpm, and fuel-air ratios from 0.063 to 0.100. The effect of exhaust pressure on engine cooling was satisfactorily incorporated in the NACA cooling-correlation method as a variation in effective gas temperature with exhaust pressure. Large variations of cylinder-head temperature with exhaust pressure were obtained for operation at constant charge flow" (p. 1).

"Previous performance data of the 19XB axial-flow compressor indicated that the outlet guide vanes and possibly the inlet guide vanes were stalling. Calculations were made to determine if these adverse conditions could be eliminated and if the manufacturer's design specifications could be more nearly approached by altering the blade angles of the first few compression stages as well as the outlet guide vanes. With the blade angles altered, experimental data were taken at compressor speeds of 8500 to 17,000 rpm with inlet-air conditions of 7.4 inches of mercury absolute and 59 degrees Fahrenheit" (p. 1).