Directory of "the names and addresses of three different categories of lenders licensed by this agency [as well as] the type license(s) held, the license number, the principal types of loans made under the authority of the license(s) held, and a code indicating whether the licensee is affiliated with others or is an independent operator" (introduction).

"The purpose of this pamphlet is to support the U.S. Army Command Maintenance Program (COMAINT). It is designed to provide supervisors and other users with a consolidated, simplified reference on use of troubleshooting equipment authorized at the organizational maintenance level" (p. i).

Plan describing existing resources and infrastructure as well as future goals for the criminal justice system in Texas.

Plan describing existing resources and infrastructure as well as future goals for the criminal justice system in Texas.

Plan describing existing resources and infrastructure as well as future goals for the criminal justice system in Texas.

Data gathered at well water sites in the Sierra Vieja detail area, including applicable water chemistry measurements (e.g., pH, conductivity, alkalinity), physical measurements (e.g., temperature, well description, scintillometer readings), and elemental analyses.

Data gathered at stream sediment sites in the Sierra Vieja detail area, including applicable water chemistry measurements (e.g., pH, conductivity, alkalinity) and elemental analyses.

Documentation outlining characteristics of field data samples taken in the Sierra Vieja detail area.

"This is a report on the first phase of the Metallogenic Project, a project conducted by the geology Division of Lucius Pitkin, Inc. for the Resource Division of the U.S. Atomic Energy Commission, Grand Junction Colorado"

Average record data listings taken during aerial gamma-ray and magnetic surveys of the Baker quadrangle in Idaho and Oregon.

Single record data listings taken during aerial gamma-ray and magnetic surveys of the Baker quadrangle in Idaho and Oregon.

The following report provides results from a geochemical survey for Trans-Pecos, Texas. Field and laboratory data are presented for 29 groundwater and 240 stream sediment samples.

The following report presents results of the Tascotal detailed geochemical survey for Trans-Pecos, Texas. Field and laboratory data are presented for 337 groundwater and 611 stream sediment samples.

Final report documenting a high-sensitivity airborne gamma radiation and magnetic field survey of the Walker Lake National Topographic Map segment (NJ 11-4 quadrangle) including a description of the program and results.

Final report documenting a high-sensitivity airborne gamma radiation and magnetic field survey of the Baker National Topographic Map segment (NL 11-11 quadrangle) including a description of the program and results.

The following report is the first of two volumes describing the program and results of the airborne gamma and total magnetic field surveys of the Reno quadrangle conducted between October 4-November 10, 1977.

The technology verification phase program plan of the Dynamic Isotope Power System (DIPS) project is presented. DIPS is a project to develop a 0.5 to 2.0 kW power system for spacecraft using an isotope heat source and a closed-cycle Rankine power-system with an organic working fluid. The technology verification phase's purposes are to increase the system efficiency to over 18%, to demonstrate system reliability, and to provide an estimate for flight test scheduling. Progress toward these goals is reported. (LCL)

This is a summary of the techniques used and the results obtained in the study of creep at high pressure, pressure dependence of yield stress and elastic constants, etc. 58 references. (DLC)

Compressive creep tests were performed on molybenum samples exposed to four different pre-test conditions: (1) annealed; (2) annealed and neutron irradiated at 480/sup 0/C to a fluence of 5 x 10/sup 19/ n cm/sup -2/ (E > 1 MeV); (3) stress-relieved; and (4) stress-relieved and neutron irradiated at reactor ambient temperature to a fluence of 1 x 10/sup 19/ n cm/sup -2/ (E > 1 MeV). The tests were performed in the temperature range of 600 to 900/sup 0/C with an initial applied stress of 176.5 MPa. Both pre- and post-test specimens were examined using electron microscopy and the relationship between substructure and mechanical properties is discussed. Possible controlling mechanisms of deformation are proposed and activation energies for creep are determined.

Surface temperatures in electron beam welding cavities in stainless steel 304 and aluminum 1100, 2024, and 6061 were measured with a narrow band infrared radiation pyrometer. A special device was designed for mounting the radiation-sensing probe next to the electron beam gun in the welding chamber. This mounting device included a mechanism for oscillating the probe so as to scan the cavity region both perpendicular and parallel to the welding direction. At the center of its movement the probe viewed almost directly down into the welding cavity. The effect of interreflections occurring in the welding cavity were accounted for by the use of an apparent spectral cavity emittance. Typical measured cavity temperature distributions for SS-304 ranged from 1950/sup 0/C at the mouth to a peak of 2350/sup 0/C at the cavity base and from 1300 to 1650/sup 0/C for A1-1100. First approximation predictions of the cavity surface temperatures were determined by assuming a quasi-steady-state condition. The surface temperature is then a function of the vapor pressure, which is required to balance the surface tension and the hydrostatic pressure both of which tend to collapse the cavity. Base temperatures thus predicted were about 5% and 10% higher than measured for SS-304 …

This Number System Cross Reference Guide constitutes a ready reference for programing the MCS-8 Microcomputer or designing logic systems. Columns give the number equivalents of decimal, binary, octal, and hexidecimal systems for decimal numbers zero through 255, as well as a corresponding teletype character opposite each row of equivalent numbers. (RWR)

None

A summary of the Brayton Isotope Power Systems (BIPS) design layout drawings is presented. These drawings were generated in compliance with Task 3 (Preliminary Design of the BIPS Ground Demonstration System) of Phase I of the ERDA sponsored BIPS contract E(04-3)-1123.

The specific objectives of the project are to determine on a geographic basis the current and potential USA production capability for grain and grass crops, to perform a preliminary screening of conversion processes, and to perform preliminary technical and economic feasibility analyses. The results obtained to date on biomass production, conversion processes, and data management are reported. (JSR)