From Introduction: "Results are presented to indicate the effect of altitude, flight Mach number, and exhaust-nozzle-outlet area on the combustion efficiency, the losses in total pressure occurring in the combustion chamber, and the fractional loss in engine cycle efficiency resulting from combustion-chamber pressure losses. The engine cycle efficiency is also presented.These results are shown graphically as a fraction of corrected engine speed and in tabular form."

From Summary: "A matrix method is presented for determining the longitudinal-stability coefficients and frequency response of an aircraft from arbitrary maneuvers. The method is devised so that it can be applied to time-history measurements of combinations of such simple quantities as angle of attack, pitching velocity, load factor, elevator angle, and hinge moment to obtain the over-all coefficients. Although the method has been devised primarily for the evaluation of stability coefficients which are of primary interest in most aircraft loads and stability studies, it can be used also, with a simple additional computation, to determine the frequency-response characteristics. The entire procedure can be applied or extended to other problems which can be expressed by linear differential equations."

None

This technical report presents results of nuclear plate work carried out to determine the neutron energy distribution inside the Los Alamos fast reactor. Most of the distributions which were investigated are valid over the energy region from 0.4 to 6 Mev. The results show that at the center of the reactor pot about 65% of the neutrons are located below 1 Mev in a rather narrow energy region which has a maximum in the neighborhood of 0.5 to 0.6 Mev. Above 2 Mev the energy distribution is similar to that of a plutonium fission neutron spectrum, i.e. the spectrum decreases exponentially, diminishing by a factor of 10 in intensity over an energy range of about 4 Mev. The leading geometry of the reactor pot does not seem to appreciably affect the spectrum at the center of the pot. However, spectra determined outside the pot can be significantly altered by the particular viewing geometry employed to examine the neutrons coming from the center of the reactor.

This document provides a discussion of the design features for the P-10X Project needed in Building 109-B.

Report discussing research on the disposal of radioactive waste, specifically second-cycle waste and first-cycle neutralized waste. "In the absence of established environmental tolerances, the investigation reported herein have been directed for the most part in developing general methods of removing radioactivity from certain waste solutions to as low a value as practical."

"Tabulated pressure coefficients and aerodynamic characteristics are presented unanalyzed for six spanwise stations on the right wing of the Douglas D-558-I research airplane (BuAero No. 37972). The data were obtained in a 1 g stall at subcritical Mach numbers, in a speed run to a Mach number of 0.90 and in a wind-up turn at a Mach number of 0.86" (p. 1).

This memorandum concerns the relative activities of Argon 41 and Nitrogen 16 in the pile gas composed of 95 percent carbon dioxide and 5 percent air. The memorandum is dated November 16, 1950. (JL)

Uranium can be rolled from cast metal or forged ingot to sheet satisfactory for cupping, deep drawing, and similar fabrication procedures by a combination of hot breakdown in the neighborhood of 600 deg C and warm finishing at 225 to 325 deg C. Sheet may also be obtained by hot rolling alone and by warm rolling alone. However, it is difficult to secure a uniform, controlled grain size by hot rolling only and warm rolling is time consuming because of the limited reduction per pass obtainable. The combination of hot and warm rolling afforded best and most practical method to secure good quality sheet in the quantity required. The percent reduction by hot working does not appear to be critical, but at least 60% warm reduction is desirable to obtain complete and controlled grain size by recrystallization with high ductility and strength properties. Except for research investigation, rolling of uranium below 225 deg C is not recommended. In the temperature range considered (below 225 deg C), reduction is difficult and must be limited to one to two percent if edge cracking is to be avoided. Hot rolling of unplated uranium from the as-cast or as-forged surface is recommended, using a …

Uranium can be rolled from cast metal or forged ingot to sheet satisfactory for cupping, deep drawing, and similar fabrication procedures by a combination of hot breakdown in the neighborhood of 600 deg C and warm finishing at 225 to 325 deg C. Sheet may also be obtained by hot rolling alone and by warm rolling alone, but the combination of hot and warm rolling afforded the best and most practical method to secure good quality sheet in the quantity required. The percent reduction by hot working does not appear to be critical, but at least 60% warm reduction is desirable to obtain complete and controlled grain size by recrystallization with high ductility and strength properties. Except for research investigation, rolling of uranium below 225 deg C is not recommended. Hot rolling of unplated uranium from the as-cast or as-forged surface is recommended, using a bath of 35% Li/sub 2/CO/sub 3/ plus 65% K/sub 2/CO/sub 3/ for a heating medium. No further preparation other than washing the salt from the hot rolled surface is required before warm rolling, and a bath of Meltemp No. 7 oil is recommended for warm rolling. Starting with an as-cast tensile strength averaging 60,000 psi, …

Summary: "This investigation showed that a sound , weather-resistant coating can be applied to uranium that the surface to be plated is cleaned and etched properly. Using the proposed two-bath plating method at 80 C., a four-mil nickel coat can be deposited in thirteen hours."

Report presenting the results of static tests conducted for the purpose of determining the lift forces and hinge moments associated with a flat-plate paddle vane, externally hinged near a rocket-nozzle exit and operating on the jet for vane deflection angles ranging from -4 degrees to 25 degrees. Results regarding vane aerodynamic characteristics, performance of rocket motor, and vane erosion

Abstract: "The effects of acidity on extraction of vanadium and molybdenum by diethyl ether are described. Solubility data for several vanadium compounds in nitrate process solutions are presented. Preliminary results on the extraction of uranium from process slurries by tributyl phosphate are reported, including data on the contaminants extracted with the uranium."

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Price Daniel, regarding a legal question submitted for clarification: Authority of the Comptroller of Public Accounts to issue a duplicate warrant without getting a bond from the payee when the original warrant never reached the payee.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Price Daniel, regarding a legal question submitted for clarification: Proper form for citations in delinquent personal property tax suits.

Report presenting an investigation to determine the aerodynamic characteristics of a wing-fuselage configuration with a wing with quarter-chord line swept back 35 degrees, an aspect ratio of 4, a taper ratio of 0.6, and an NACA 65A006 airfoil section. Lift, drag, and pitching-moment characteristics, downwash angles, and wake characteristics for various angles of attack and Mach numbers are provided.

The work to determine the feasibility of using a quickoperating closure for the pressure vessel of the controlled Recirculation Boiling Reactor is described. An outline of the worb performed and the conclusions made is given. Datailed results of the self-energizing seal-evaluation tests are given. (W.D.M.)

From introduction: "This is the ninth monthly report, BMI-514, under Contract No. AT(30-1)-771 on "Zirconium Research and Development". The report covers the work period from September 15, 1950, to October 15, 1950. Work is continuing on the preparation of large-diameter zirconium crystal bars in the 16-inch-diameter de Boer unit. Crystal bars up to 1-5/16 inches in diameter and 8 feet long have been prepared in this unit."

A zirconium crystal bar, weighing 29 pounds and 1 5/16 inches in diameter by 8 feet in over-all length, was prepared, using pear-shaped zirconium couples to join the filament to the electrodes. This crystal bar was the largest produced to date in the 16-in.-diam. de Boer unit. The design of the couplings was modified to incorporate improvements indicated by the initial run, and another run is in progress. Binary alloys of Zr and Ni, Cr, and Si, as well as a zirconium alloy containing Fe, Al, and Si, were prepared for use as feed material in the small pyrex de Boer bulbs. The transfer of these elements from the feed to the crystal bar is being investigated. The rate of deposition and the type of crystal structure obtained with additions of various amounts of iodine are being studied. (auth)

Effect of x irradiation in oxygen and in hydrogen on chromosome aberration frequency in tradescantia microspores.

Abstract: "Costs have been estimated for the production of uranium and pure thorium from monasite concentrates by a process involving (1) reaction of monasite with caustic soda, (2) dissolution of the hydrous oxides in hydrochloric acid, (3) separation from the bulk of the rare earths by hydroxide precipitation of thorium and uranium, and (4) purification by solvent extraction."

Costs are estimated for the production of uranium and pure thorium from monazite concentrates. The process involves; reaction of the monazite with caustic soda, dissolution of the hydrous oxides in hydrochloric acid, separation from the bulk of the rare earths by hydroxide precipitation of thorium and uranium, and purification by solvent extraction. (auth)

Report presenting an investigation in the high speed tunnel to determine the effects of several wing-mounted external-store configurations on the aerodynamic characteristics of a model of a swept wing-fuselage combination for a range of Mach numbers. Some of the configurations explored included inboard underwing installations and wing-tip installations. Results regarding lift-drag ratios, drag characteristics, lift-curve slope, and pitching-moment characteristics are provided.

Report describing a method for recovery of high yields of thorium and uranium from monazite sand concentrates. Monazite is decomposed into hydrous metal oxides, which are dissolved in an acid. The solution is then separated into a precipitate, which seperates from thorium and uranium. An alternate separation method is evaluated.