A report which deals with the Redox IA Column studies made in small-scale columns packed with 3/16-in. Fenske helices and using NH4NO3 salting agent.

Introduction: In anticipation of the design of equipment for heat transfer tests, a series of short exposure corrosion tests was initiated in an effort to determine the order of magnitude of the corrosion involved. Information was required on the effect on corrosion rates of applying a potential between two concentric tubes, the annulus between them containing condensate water.

From introduction: "This report gives the results of a 1000-hour corrosion test of SAE 1010, low carbon steel, in synthetic Redox waste solutions...The present test was designed to obtain corrosion rates for waste solution temperatures of 180 F, 200 F, and 220 F in solutions neutralized to pH values of 11, 12, and 13.

This report discusses a proposed method for treating the effect of increasing critical mass of plutonium solutions, which occurs when hydrogen density is reduced by dilution with heavier nuclei.

The following report provides complete data and test procedure from hot water corrosion tests of type 502 stainless steel.

Purpose: "The Hanford Works Analytical Manual for Process Water is designed to specify the analytical methods to be applied for control purposes in the Reactor Section, Process Sub-Section laboratories. The procedures are in general form and serve as references rather than outlined laboratory instructions. The manual us designed to replace the "Hanford Works Manual," HW-12862."

This report examines the failure of two 18-8 grade stainless steel gate valves used in sulfamic acid and determines the cause of the failures through a series of tests.

The following report is one of a series of rolling tests to establish the rolling process for Feed Materials Production Center at Fernold, Ohio. The primary objective of this program is to find a mechanically feasible process for continuous rolling of uranium.

Considerable work has been done on decontamination procedures for both corrosion products and fission products. Testing of promising procedures under typical rupture conditions is an important phase of this work. The Irradiated Rupture Prototype (IRP) has been used since August in this evaluation work. This document is one of a series reporting these data.

This report summarizes experimental results obtained for the General Electric Company under terms of Design, Development and Research Contrast DDR-33. A discussion of the results, the manner in which they were obtained and their probable accuracy are included. Suggested improvements or modifications of properties of this nature be contemplated.

A part of the development activities of the Process Equipment Development Group, Chemical Development, HLO through the year 1959 has consisted of test evaluation of some of the never products of manufacturers, design and refinement of novel units to do certain specialized jobs and development of improved components for existing plant equipment. Modification of present chemical processing methods and investigation of new basic procedures have made it necessary to utilize different and "exotic" materials, titanium, has given rise to another problem-- that of the selection of adequate and compatible bearings where the titanium is used as moving or rotating part.

This report was written to describe the instrument and test results obtained. It is understandably imperative that such alarming devices be incorporated in various areas of the plant to provide an alarm or warning for increasing dose rate from gauss radiation fields.

A previous study has been completed on the buildup and decay of xenon poisoning in the PRTR by simulating the reactor as a single region. The results of this study indicated that a study using a more refined model of the reactor would be valuable.

In the decladding of stainless steel clad fuel elements with sulfuric acid (the Sulfex process), the loss of core material to the decladding solution is determined by the rate of reaction of the core material with the solution and the time of exposure if the core to the solution. Since very little was known about the effects of irradiation history on the rates at which core materials dissolve in sulfuric acid, the present study was undertaken in an effort to determine the magnitude of such effects. This report summarizes the results obtained to date. Further work is planned when materials of higher burn-up are available.

In October 1959, a combination testing station developed at HAPO was reported to the Sheath committee. This testing station consisted of electronic instrumentation and mechanical scanning equipment to check coextruded fuel elements (rod and tube) for clad thickness, clad integrity, bond, and core integrity. The clad tests are performed by eddy current methods and the other are ultrasonic.