Report presenting a flight investigation to determine the comparative performance of AN-F-58 and AN-F-32 fuels in a 4000-pound-thrust turbojet engine. The fuels were equivalent over the range of conditions investigated. Results regarding corrected net thrust, corrected jet-fuel consumption, variation of corrected tail-pipe temperature, combustor blow-out speeds, and visual observations of the jet exhaust are provided.

Report discussing testing to determine the drag characteristics at zero lift of a wing with a circular-arc airfoil section with a maximum thickness of 9 percent chord. The results were compared to previous testing on an NACA 65-009 airfoil. It was found that the NACA airfoil had lower drag coefficients than the circular-arc airfoil tested in this experiment.

Report presenting an analysis of a number of free-flight transient responses resulting from small stabilizer movements obtained during testing of the Bell X-1 airplane to obtain its longitudinal stability characteristics. A comparison of flight data and model test data is also provided.

Report presenting the aerodynamic characteristics of a new type of lateral control through a range of Mach numbers. The control consisted of airfoils mounted vertically at the tips of the wing and could be rotated to induce rolling moments or lift on the wing surface. Results regarding lateral-control characteristics and lift-control characteristics are provided.

Report discussing tests of a scale model of the XB-51 airplane to determine its force, stability, and control characteristics in pitch and yaw at various Mach numbers. The effects of the dive breaks and the bomb bay are also described.

"Results are presented of an investigation to determine the pressure distributions on a wing with leading-edge sweepback decreasing from 45 degrees at the root to 20 degrees at the tip, an aspect ratio of 4.12, taper ratio of 0.36, and NACA 64A009 airfoil section. Tests were conducted at a Reynolds number of 3.5 x 10(exp 6) and a Mach number of 0.07 on the wing with and without 0.20 chord and 0.65 span split flaps deflected 60 degrees. These pressure distributions are analysed herein to determine the character of flow and its effect on the stability of the wing" (p. 1).

"An investigation was made at the Langley landing-loads track to obtain data on the coefficient of friction during wheel spin-up. A landing gear was tested at horizontal velocities ranging from 0 to 180 feet per second together with vertical velocities of 7.0 and 9.3 feet per second. The results indicate the effect of forward speed and tire inflation pressure on the coefficient of friction" (p. 1).

Report presenting an investigation in the free-flight tunnel to determine the dynamic lateral stability and control characteristics of a high-aspect-ratio bomber model with self-supporting, free-floating fuel tanks attached to the wing tips. The results showed that the flight behavior of the configuration could be made satisfactory when sufficient restoring moment was supplied. Results regarding the flight behavior, rolling motions, motions of the bomber and attached tanks, and flight records for different gearing ratios are provided.

Powered models of three different flying boats were landed in oncoming wave of various heights and lengths. The resulting motions and acceleration were recorded to survey the effects of varying the trim at landing, the deceleration after landing, and the size of the waves. One of the models had an unusually long afterbody. The data for landing with normal rates of deceleration indicated that the most severe motions and accelerations were likely to occur at some period of the landing run subsequent to the initial impact.

Report presenting a test-stand investigation conducted on a rectangular ramjet engine design for installation in an aircraft wing. The engine operated without excessive engine noise or vibration over the entire range of operating conditions. Results regarding inlet velocity, exhaust flame characteristics, fuel-air ratio, and total-temperature rise are provided.

From Summary: "The results of force tests made at low speed are presented to show the effect of longitudinal static stability produced by drooping the tip of a 63 degree sweptback wing. Five semispan wing models were tested: two incorporated curved drooped tips, two with abruptly drooped tips, and one without droop. The most favorable stability characteristics were measured for a model with an abruptly drooped tip, a fence, and a leading-edge flap; however, the use of these same auxiliary devices on the undrooped wing was nearly as effective."

Report presenting measurements of the damping in roll of cruciform triangular wings of aspect ratios 0.64, 1.28, and 2.31 at supersonic Mach numbers from 1.5 to 6.0. The models were launched from rifled guns and the time history of the model roll position in free flight was explored. Results regarding the comparison with theory, transonic effects, and comparison with results at other facilities are provided.

Report presenting a comparison of the performance of a German Jumo 004 can-type combustor and the performance of two contemporary United States turbojet combustors to determine whether the Jumo 004 was more advanced and to determine whether there are basic, inherent differences in the performance achieved with the can or annular combustor type. Results regarding altitude operational limits, combustion efficiency, pressure loss, and temperature profile at combustor outlet are provided.

Report presenting an investigation of a model of the Chance Vought XF8U-1 airplane to determine the effect of spin-recovery rockets on the recovery characteristics of the model. The investigation also included tests to determine the effect of simulated engine thrust on the recovery characteristics of the model. Results regarding yaw rockets, thrust-simulation rocket, and roll rockets are provided.

Report presenting an experimental wing-flutter investigation in the transonic blowdown tunnel, which is equipped with a slotted test section, in order to determine the correlation between transonic-wind-tunnel and free-fall flight flutter results. Very good agreement was observed between wind tunnel and flight flutter test results, which showed the feasibility of conducting flutter tests in transonic wind tunnels with slotted test sections.

An experimental investigation was carried out to determine the boundary-layer transition characteristics of bodies of revolution with flat and nearly flat faces. Shadowgraphs indicated that the boundary layer remained laminar on the front faces and was turbulent only on the sides. The tests also yielded information on the total drag coefficients and static longitudinal stability of the models.

Report presenting local coefficients of convective heat transfer as measured from skin temperature along the body of an RM-10 NACA research missile, which consisted of a parabolic body of revolution. Results regarding recovery factors, adiabatic wall temperatures, Nusselts, Prandtl, and Reynolds numbers, and boundary-layer transition are provided.

"Results of an investigation by the free-fall method are presented herein for a configuration having a body of revolution of fineness ratio 12 and 45 degrees sweptback wing mounted aft of the maximum diameter of the body. The fillets were designed to provide large increases in the sweep of the leading edge and the line of maximum thickness as the wing root was approached. Comparison of these results with those for the same configuration without fillets shows that the addition of wing fillets increased the total drag of the configuration by about 35 percent at Mach numbers near 1.0 and about 15 percent at Mach numbers near 1.2" (p. 1).

Memorandum presenting an investigation of the problems associated with the design of a low-pressure-loss, short afterburner for sea-level thrust augmentation in a static, sea-level test stand. Results regarding diffuser pressure losses, afterburner pressure losses, and afterburner performance are provided.

Report presenting an investigation of the problems associated with the design of a low-pressure-loss, short afterburner for sea-level thrust augmentation in a static, sea-level test stand using the power section of a 5970-pound-thrust, axial-flow turbojet engine. The various portions of the afterburner and procedures used to test it are described. Results regarding diffuser pressure losses, afterburner pressure losses, and afterburner performance are provided.

Report presenting an investigation in a mixing-zone apparatus to determine the effects of jet flow on two-dimensional base pressure and the development of supersonic channel flow about a two-dimensional base, with and without splitter plates of different thicknesses. Results regarding the starting cycle for outer streams only, the fully established supersonic flow, and the base pressure between the center jet and outer streams are provided.

Report presenting a wind-tunnel investigation of a semispan delta wing with the leading-edge swept back 60 degrees. A half-delta control surface was used and testing was performed with and without fences. Results regarding the rolling effectiveness, wing characteristics, and control-surface characteristics are provided.

Report presenting an experimental investigation at Mach number 1.90 to determine the overall performance capabilities of axisymmetric two-cone and isentropic nose inlets in terms of total-pressure recovery, mass flow, and external drags. At zero angle of attack, the external drag was separated into their components of cowl pressure, friction, and additive drags. Results regarding total-pressure recovery and mass-flow characteristics, total-pressure profiles at diffuser exit, cowl-pressure distributions and drag, zero-angle-of-attack component breakdown of external drag, and overall performance comparison are provided.

Report presenting an examination of the use of an axisymmetric variable-geometry technique for achieving good supersonic inlet performance over a wide range of Mach numbers. An inlet with a telescoping spike was designed and experimentally evaluated. Results regarding the spike survey study and variable-geometry-inlet study are provided.