Paper describes the results of studies testing the creep resistance of two multi-principal element alloys, CoCrNi and CoCrFeMnNi.

The article reports on the shear deformation of a eutectic structured HEA and effect of precipitation on shear deformation, particularly Al₀.₇CoCrFeNi high-entropy alloy (HEA). A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local dynamic shear response of the alloy. The change in the width of shear bands with respect to precipitation and deformation rates was studied. The precipitation of L1₂ phase did not delay the formation of adiabatic shear bands (ASB) or affect the ASB width significantly, however, the deformed region around ASB, consisting of high density of twins in fcc phase, was reduced from 80 µm to 20 µm in the stronger precipitation strengthened condition.

In this article the time-dependent plastic deformation behavior of two refractory high entropy alloys was investigated, namely HfTaTiVZr and TaTiVWZr. These alloys are based on reduced activity metals from the 4-5-6 elemental palette that would allow easy post-service recycling after use in nuclear reactors. The creep behavior was investigated using nano-indentation over the temperature range of 298 K to 573 K under static and dynamic loads up to 5 N.

Paper investigates the mobility dynamics in wireless sensor networks analytically, and discusses the advantages of the leader-follower model.

Describes the development of a strong mold-resistant adhesive by incorporating soybean meal and blood meal.

This article highlights a study of a bio adhesive was developed from soybean meal and larch tannin that was designed for exterior use. Phenol hydroxymethylated tannin oligomer (PHTO) was synthesized and then mixed with soybean meal flour in order to obtain a soybean meal-based adhesive (SPA). The results showed that the moisture absorption rate, residual rate, and solid content of SPA with 10 wt % PHTO (mass ratio with respect to the entire adhesive) were improved by 22.8%, 11.6%, and 6.8%, respectively, as compared with that of pure SPA.

This article presents the design, modeling, and experimental characterization of flexible square-shaped spiral coils with different scaling factors for WPT systems. The effects of coil scaling factor on inductance, capacitance, resistance, and the quality factor (Q-factor) are modeled, simulated, and experimentally validated for the case of flexible planar coils. This article also presents the effect of skin contact with the flexible coil in terms of the power transfer efficiency (PTE) to validate the suitability as a wearable sensor.

Article describes examination of the appearance, color, chemical composition, and physiology and mechanical properties of densified Abies wood before and after densification treatment using a colorimeter, FTIR and mechanical testing machine.

Article describes a study where laser surface engineering was successfully used to engineer a nano carbide composite coating on a low carbon steel substrate.

Article presents a simple 3D electroporation platform that enables massively parallel single-cell manipulation and the intracellular delivery of macromolecules and small molecules.

Article describes development of an ultrafine-grained magnesium alloy with an extraordinary strength and ductility combination, exceptional high specific strength, zero yield strength asymmetry and excellent high strain rate superplasticity.

Article describes study analyzing the chemical components of elliptical kiwifruit (Actinidia chinensis Planch) using Fourier transform infrared spectroscopy (FT-IR) and gas chromatography mass spectrometry (GC–MS) technologies.

Article proposes a Social- and Content-aware Video content delivery Prediction method (SCVP) to address the problem of predicting whether a video will be watched by a user for efficient video content delivery in mobile social networks.

An introduction to a series of research articles submitted on the topic of "Catalysts for Clean Energy Conversion and Storage".

Article discusses a novel eutectoid nano-lamellar (FCC + L12)/(BCC + B2) microstructure that has been discovered in a relatively simple Al0.3CoFeNi high entropy alloy (HEA) or complex concentrated alloy (CCA).

Article describes study analyzing the characteristics of the movement of the gel extinguishing agent micelles by considering the resistance of movement.

Article presents an in-depth discussion of liquid crystal blue phases (BPs).

Article describes study which sought to evaluate methods for activity recognition for toddlers.

Article describes study which sought to evaluate the efficiency of pilot water desalination system treating brackish water which was obtained mixing fresh water and seawater up to reach 1,500 mg L-1 of total dissolved solids (TDS) concentration.

Data management plan for the grant, "CAREER: Manufacturing of Mechanically Stable Nanoporous Ceramic Structures Via Selective Infiltration of Polymer Templates." This Faculty Early Career Development (CAREER) grant from the National Science Foundation supports fundamental research to elucidate a new strategy of manufacturing nanoporous ceramic structures with controllable structure and composition and programmable mechanical stability. The specific goal of this research is to discover processing-structure-property relationships in ceramic coatings and heterostructures by providing fundamental insights on the mechanism of liquid phase swelling-based infiltration of spin-coated polymer templates with inorganic precursors and defining the rules that control the resulting structure and, thus, access to various materials surfaces and interfaces.

Data management plan for the grant, "CAREER: Reinventing Network-on-Chips of GPU-Accelerated Systems." Research seeking to reinvent on-chip networks for GPU-accelerated systems to remove a communication bottleneck. A major outcome of the project is a set of techniques that enable the development of effective and efficient network-on-chip architectures. Graphics processing units (GPUs) have rapidly evolved to become high-performance accelerators for data-parallel computing. To fully take advantage of the computing power of GPUs, on-chip networks need to provide timely data movement to satisfy the requests of data by the processing cores. Currently, there exists a big gap between the fast-growing processing power of the GPU processing cores and the slow-increasing on-chip network bandwidth. Because of this, GPU-accelerated systems are interconnect-dominated and the on-chip network becomes their performance bottleneck.

Data management plan for the grant, "CAREER: Fundamental Limits of Cryptographic Primitives Through Network Information Theory." Research project studying the fundamental limits of a diverse array of cryptographic primitives through network information theory and coding tools. The project takes an information theoretic view of the investigation of the fundamental limits of cryptographic primitives. The project is expected to unveil theoretical and practical insights into cryptographic primitives, and enhance the understanding on their fundamental limits.

Data management plan for the grant, "REU Site: Interdisciplinary Research Experience on Accelerated Deep Learning through A Hardware-Software Collaborative Approach." This Research Experiences for Undergraduates (REU) Site Program at the University of North Texas will enhance the knowledge and research skills of a diverse cohort of undergraduate students through empowering, innovative, and interdisciplinary research experiences in developing Deep Learning applications and systems. The program aims to 1) expose undergraduate students to real-world and cutting-edge research focused on accelerated deep learning through combined hardware and software development; 2) encourage more undergraduate students to continue their academic careers and seek graduate degrees in computer science, computer engineering, and related disciplines; 3) develop research skills and improve communication and collaborative skills in undergraduate students.

Data management plan for the grant "Charge Transport in Two-Dimensional Materials Based Integrated Flexible Energy System."