Paper describes the results of studies testing the creep resistance of two multi-principal element alloys, CoCrNi and CoCrFeMnNi.

The article reports on the shear deformation of a eutectic structured HEA and effect of precipitation on shear deformation, particularly Al₀.₇CoCrFeNi high-entropy alloy (HEA). A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local dynamic shear response of the alloy. The change in the width of shear bands with respect to precipitation and deformation rates was studied. The precipitation of L1₂ phase did not delay the formation of adiabatic shear bands (ASB) or affect the ASB width significantly, however, the deformed region around ASB, consisting of high density of twins in fcc phase, was reduced from 80 µm to 20 µm in the stronger precipitation strengthened condition.

In this article the time-dependent plastic deformation behavior of two refractory high entropy alloys was investigated, namely HfTaTiVZr and TaTiVWZr. These alloys are based on reduced activity metals from the 4-5-6 elemental palette that would allow easy post-service recycling after use in nuclear reactors. The creep behavior was investigated using nano-indentation over the temperature range of 298 K to 573 K under static and dynamic loads up to 5 N.

Paper investigates the mobility dynamics in wireless sensor networks analytically, and discusses the advantages of the leader-follower model.

Describes the development of a strong mold-resistant adhesive by incorporating soybean meal and blood meal.

This article highlights a study of a bio adhesive was developed from soybean meal and larch tannin that was designed for exterior use. Phenol hydroxymethylated tannin oligomer (PHTO) was synthesized and then mixed with soybean meal flour in order to obtain a soybean meal-based adhesive (SPA). The results showed that the moisture absorption rate, residual rate, and solid content of SPA with 10 wt % PHTO (mass ratio with respect to the entire adhesive) were improved by 22.8%, 11.6%, and 6.8%, respectively, as compared with that of pure SPA.

This article presents the design, modeling, and experimental characterization of flexible square-shaped spiral coils with different scaling factors for WPT systems. The effects of coil scaling factor on inductance, capacitance, resistance, and the quality factor (Q-factor) are modeled, simulated, and experimentally validated for the case of flexible planar coils. This article also presents the effect of skin contact with the flexible coil in terms of the power transfer efficiency (PTE) to validate the suitability as a wearable sensor.

Article describes examination of the appearance, color, chemical composition, and physiology and mechanical properties of densified Abies wood before and after densification treatment using a colorimeter, FTIR and mechanical testing machine.

Article describes a study where laser surface engineering was successfully used to engineer a nano carbide composite coating on a low carbon steel substrate.

Article presents a simple 3D electroporation platform that enables massively parallel single-cell manipulation and the intracellular delivery of macromolecules and small molecules.

Article describes development of an ultrafine-grained magnesium alloy with an extraordinary strength and ductility combination, exceptional high specific strength, zero yield strength asymmetry and excellent high strain rate superplasticity.

Article describes study analyzing the chemical components of elliptical kiwifruit (Actinidia chinensis Planch) using Fourier transform infrared spectroscopy (FT-IR) and gas chromatography mass spectrometry (GC–MS) technologies.

Article proposes a Social- and Content-aware Video content delivery Prediction method (SCVP) to address the problem of predicting whether a video will be watched by a user for efficient video content delivery in mobile social networks.

An introduction to a series of research articles submitted on the topic of "Catalysts for Clean Energy Conversion and Storage".

Article discusses a novel eutectoid nano-lamellar (FCC + L12)/(BCC + B2) microstructure that has been discovered in a relatively simple Al0.3CoFeNi high entropy alloy (HEA) or complex concentrated alloy (CCA).

Article describes study analyzing the characteristics of the movement of the gel extinguishing agent micelles by considering the resistance of movement.

Article presents an in-depth discussion of liquid crystal blue phases (BPs).

Article describes study which sought to evaluate methods for activity recognition for toddlers.

Article describes study which sought to evaluate the efficiency of pilot water desalination system treating brackish water which was obtained mixing fresh water and seawater up to reach 1,500 mg L-1 of total dissolved solids (TDS) concentration.

This article reports the design, fabrication, and characterization of an all inkjet-printed field-effect transistor (FET).

Article presents the large scale synthesis of solution-processed 2D (CH₃(CH₂)₃NH₃)₂(CH₃NH₃)ₙ − 1PbₙI₃ₙ + 1 (n = 2, 3, and 4) perovskites, a family of layered compounds with composition-tunable bandgap, where inkjet printing was used to fabricate heterostructure, flexible photodetector devices. The flexible, inkjet-printed perovskite 2D heterostructures have significant potential for optoelectronic devices, which can enable broad possibilities with compositional tunability and versatility of the organohalide perovskites.

This article reports on a study where 2D TMDs (MoS₂ and WS₂) and the 3D allotrope of carbon and graphite were incorporated into acrylonitrile butadiene styrene (ABS) and polyethylene terephthalate glycol (PETG) matrices in order to form polymer matrix composites (PMCs). The multipronged analysis described in this study was motivated by the purpose to fuse together topics of low-cost, additive manufacturing with 2D layered materials, and studying their ensuing mechanical and tribological properties.

This article presents dispersions of WS₂ and h-BN using cyclohexanone and terpineol as the solvent to subsequently print prototype capacitive nanodevices.

Article exploring phonon dynamics in mechanically exfoliated two-dimensional WSe₂ using temperature-dependent and laser-power-dependent Raman and photoluminescence (PL) spectroscopy. The work reported sheds fundamental insights into the evolution of phonon dynamics in WSe₂ and should help pave the way for designing high-performance electronic, optoelectronic and thermoelectric devices in the future.