Poor air quality can greatly affect the public health. Research studies indicate that indoor air can be more polluted than the outdoor air. An indoor air quality monitoring system will help to create an awareness of the quality of air inside which will eventually help in improving it. The objective of this research is to develop a low cost wireless sensor system for indoor air quality monitoring. The major cost reduction of the system is achieved by using low priced sensors. Interface circuits had to be designed to make these sensors more accurate. The system is capable of measuring carbon dioxide, carbon monoxide, ozone, temperature, humidity and volatile organic compounds. The prototype sensor node modules were developed. The sensor nodes were the connected together by Zigbee network. The nodes were developed in such a way that it is compact in size and wireless connection of sensor nodes enable to collect air quality data from multiple locations simultaneously. The collected data was stored in a computer. We employed linear least-square approach for the calibration of each sensor to derive a conversion formula for converting the sensor readings to engineering units. The system was tested with different pollutants and data collected was …

This thesis proposes a design of a rapidly deployable cellular network prototype that provides voice and data communications and it is interoperable with legacy devices and the existing network infrastructure. The prototype is based on software defined radio and makes use of IEEE 802.11 unlicensed wireless radio frequency (RF) band for backhaul link and an open source GSM implementation software. The prototype is also evaluated in environments where there is limited control of the radio frequency landscape, and using Voice Over Internet Protocol (VoIP) performance metrics to measure the quality of service. It is observed that in environments where the IEEE 802.11 band is not heavily utilized, a large number of calls are supported with good quality of service. However, when this band is heavily utilized only a few calls can be supported as the quality of service rapidly degrades with increasing number of calls, which is due to interference. It is concluded that in order to achieve tolerable voice quality, unused licensed spectrum is needed for backhaul communication between base stations.

Memory is an important part of any digital processing system. On-chip SRAM can be found in various levels of the memory hierarchy in a processor and occupies a considerable area of the chip. Leakage is one of the challenges which shrinking of technology has introduced and the leakage of SRAM constitutes a substantial part of the total leakage power of the chip due to its large area and the fact that many of the cells are idle without any access. In this thesis, we introduce asymmetric SRAM cells using stacked transistors which reduce the leakage up to 26% while increasing the delay of the cell by only 1.2% while reducing the read noise margin of the cell by only 15.7%. We also investigate an asymmetric cell configuration in which increases the delay by 33% while reduces the leakage up to 30% and reducing the read noise margin by only 1.2% compared to a regular SRAM cell.

In this thesis, I present my study on the impact of multi-group network structure on the performance of consensus building strategies, and the preliminary mathematical formulation of the problem on improving the performance of the National Airspace system (NAS) through long-term investment. The first part of the thesis is concerned with a structural approach to the consensus building problem in multi-group distributed sensor networks (DSNs) that can be represented by bipartite graph. Direct inference of the convergence behavior of consensus strategies from multi-group DSN structure is one of the contributions of this thesis. The insights gained from the analysis facilitate the design and development of DSNs that meet specific performance criteria. The other part of the thesis is concerned with long-term planning and development of the NAS at a network level, by formulating the planning problem as a resource allocation problem for a flow network. The network-level model viewpoint on NAS planning and development will give insight to the structure of future NAS and will allow evaluation of various paradigms for the planning problem.

Mobile wireless sensor networks are not widely implemented in the real world, even after years of research carried out in this field. One reason is the lack of understanding of the impact that mobility has on network performance. The simulation and emulation of mobile wireless sensor networks is necessary before they are deployed for the real-world applications. This thesis presents a simulation-based study of different mobility models. The total area coverage that depends on the pattern of node movements is observed through simulations. The spatial distribution of node locations is also studied. Various synthetic mobility models available are explored based on their theoretical descriptions. ‘BonnMotion' is used as the network simulator for investigating different mobility scenarios. The results obtained after simulations are imported to MATLAB and the analysis of node movements is done through various plots and inferences from the data. The comparison of mobility models is also discussed based on their spatial node distribution in the simulated scenarios.

In game based learning, motivating the players to learn by providing them a desirable gameplay experience is extremely important. However, it's not an easy task considering the quality of today's commercial non-educational games. Throughout the gameplay, the player should neither get overwhelmed nor under-challenged. The best way to do so is to monitor the player's actions in the game because these actions can tell the reason behind the player's performance. They can also tell about the player's lacking competencies or knowledge. Based on this information, in-game educational interventions in the form of hints can be provided to the player. The success of such games depends on their interactivity, motivational outlook and thus player retention. UNTANGLED is an online mapping game based on crowd-sourcing, developed by Reconfigurable Computing Lab, UNT for the mapping problem of CGRAs. It is also an educational game for teaching the concepts of reconfigurable computing. This thesis performs qualitative comparative analysis on gameplays of low performing players of UNTANGLED. And the implications of this analysis are used to provide recommendations for improving the gameplay experience for these players by guiding them. The recommendations include strategies to reach a high score and a compact solution, hints in the …

In wireless communication systems, one of the most important resources being focused on all the researchers is spectrum. A cognitive radio (CR) system is one of the efficient ways to access the radio spectrum opportunistically, and efficiently use the available underutilized licensed spectrum. Spectrum utilization can be significantly enhanced by developing more applications with adopting CR technology. CR systems are implemented using a radio technology called software-defined radios (SDR). SDR provides a flexible and cost-effective solution to fulfil the requirements of end users. We can see a lot of innovations in Internet of Things (IoT) and increasing number of smart devices. Hence, a CR system application involving an IoT device is studied in this thesis. Opportunistic spectrum access involves two tasks of CR system: spectrum sensing and dynamic spectrum access. The functioning of the CR system is rest upon the spectrum sensing. There are different spectrum sensing techniques used to detect the spectrum holes and a few of them are discussed here in this thesis. The simplest and easiest to implement energy detection spectrum sensing technique is used here to implement the CR system. Dynamic spectrum access involves different models and strategies to access the spectrum. Amongst the available models, …

Today, there is a growing number of buildings in a neighborhood and business parks that are utilizing renewable energy generation, to reduce their electric bill and carbon footprint. The most current way of implementing a renewable energy generation is to use solar panels or a windmill to generate power; then use a charge controller connected to a battery bank to store power. Once stored, the user can then access a clean source of power from these batteries instead of the main power grid. This type of power structure is utilizing a single module system in respect of one building. As the industry of renewable power generation continues to increase, we start to see a new way of implementing the infrastructure of the power system. Instead of having just individual buildings generating power, storing power, using power, and selling power there is a fifth step that can be added, sharing power. The idea of multiple buildings connected to each other to share power has been named a microgrid by the power community. With this ability to share power in a microgrid system, a catastrophic event which cause shutdowns of power production can be better managed. This paper then discusses the data …

DC to DC converters stabilize the voltage obtained from voltage sources such as solar power system, wind energy sources, wave energy sources, rectified voltage from alternators, and so forth. Hence, the need for improving its control algorithm is inevitable. Many algorithms are applied to DC to DC converters. This thesis designs fuzzy adaptive dynamic programming (Fuzzy ADP) algorithm. Also, this thesis implements both adaptive dynamic programming (ADP) and Fuzzy ADP on DC to DC converters to observe the performance of the output voltage trajectories.

This thesis aims to utilize data analysis and predictive modeling techniques and apply them in different domains for gaining insights. The topics were chosen keeping the same in mind. Analysis of customer interests is a crucial factor in present marketing trends and hence we worked on twitter data which is a significant part of digital marketing. Neuroscience, especially psychological behavior, is an important research area. We chose eye tracking data based on which we differentiated human concentration while watching controllable (video game) videos and uncontrollable (sports) videos. Currently, cities are using data analysis for becoming smart cities. We worked on the City of Lewisville emergency services data and predicted the vehicle-accident-prone areas for development of precautionary measures in those areas.

Sensors are used to convert physical quantity into numerical data. Various types of sensors can be coupled together to make a single node. A distributed array of these nodes can be deployed to collect environmental data by using appropriate sensors. Application of low powered short range radio transceivers as a communication medium between spatially distributed sensor nodes is known as wireless sensor network. In this thesis I build such a network by using Arduino, Raspberry Pi and XBee. My goal was to accomplish a prototype system so that the collected data can be stored and managed both from local and remote locations. The system was targeted for both indoor and outdoor environment. As a part of the development a controlling application was developed to manage the sensor nodes, wireless transmission, to collect and store data using a database management service. Raspberry Pi was used as base station and webserver. Few web based application was developed for configuring the network, real time monitoring, and database management. Whole system functions as a single entity. The use of open source hardware and software made it possible to keep the cost of the system low. The successful development of the system can be considered …

This thesis presents the design of a communication system (PRCS) which improves on all aspects of the current state of the art 4G communication system Long Term Evolution (LTE) including peak to average power ratio (PAPR), data reliability, spectral efficiency and complexity using the most recent state of the art research in the field combined with novel implementations. This research is relevant and important to the field of electrical and communication engineering because it provides benefits to consumers in the form of more reliable data with higher speeds as well as a reduced burden on hardware original equipment manufacturers (OEMs). The results presented herein show up to a 3 dB reduction in PAPR, less than 10-5 bit errors at 7.5 dB signal to noise ratio (SNR) using 4QAM, up to 3 times increased throughput in the uplink mode and 10 times reduced channel coding complexity.

In situations where information infrastructure is destroyed or not available, on-demand information infrastructure is pivotal for the success of rescue missions. In this paper, a drone-carried on demand information infrastructure for long-distance WiFi transmission system is developed. It can be used in the areas including emergency response, public event, and battlefield. The WiFi network can be connected to the Internet to extend WiFi access to areas where WiFi and other Internet infrastructures are not available. In order to establish a local area network to propagate WIFI service, directional antennas and wireless routers are used to create it. Due to unstable working condition on the flying drones, a precise heading turning stage is designed to maintain the two directional antennas facing to each other. Even if external interferences change the heading of the drones, the stages will automatically rotate back to where it should be to offset the bias. Also, to maintain the same flying altitude, a ground controller is designed to measure the height of the drones so that the directional antennas can communicate to each other successfully. To verify the design of the whole system, quite a few field experiments were performed. Experiments results indicates the design is reliable, …

Training autonomous agents that are capable of performing their assigned job without fail is the ultimate goal of deep reinforcement learning. This thesis introduces a dueling Quantile Regression Deep Q-network, where the network learns the state value quantile function and advantage quantile function separately. With this network architecture the agent is able to learn to control simulated robots in the Gazebo simulator. Carefully crafted reward functions and state spaces must be designed for the agent to learn in complex non-stationary environments. When trained for only 100,000 timesteps, the agent is able reach asymptotic performance in environments with moving and stationary obstacles using only the data from the inertial measurement unit, LIDAR, and positional information. Through the use of transfer learning, the agents are also capable of formation control and flocking patterns. The performance of agents with frozen networks is improved through advice giving in Deep Q-networks by use of normalized Q-values and majority voting.

The thesis represents the design for dual-band quarter wavelength and half wavelength microstrip transmission line. Chapter 2 proposed the design of a novel dual-band asymmetric pi-shaped short-circuited quarter wavelength microstrip transmission line working at frequencies 1GHz and 1.55 GHz for 50Ω transmission line and at frequencies 1GHz and 1.43GHz for 60Ω transmission line. Chapter 3 proposed the design of a novel dual-band quarter wavelength microstrip transmission line with asymmetrically allocated open stubs and short-circuited stubs working at frequencies 1GHz and 1.32GHz. Chapter 4 proposed the design of dual-band pi-shaped open stub half wavelength microstrip transmission line working at frequencies 1GHz and 2.07GHz. Numerical simulations are performed both in HyperLynx 3D EM and in circuit simulator ADS for all of the proposed designs to measure the return loss (S11) and insertion loss (S12) in dB and phase response for S12 in degree.

Data acquisition through wireless sensor networks (WSNs) has enormous potential for scalable, distributed, real-time observations of monitored environmental parameters. Despite increasing versatility and functionalities, one critical factor that affects the operation of WSNs is limited power. WSN sensor nodes are usually battery powered, and therefore the long-term operation of the WSN greatly depends on battery capacity and the node's power consumption rate. This thesis focuses on WSN node design to reduce power consumption in order to achieve sustainable power supply. For this purpose, this thesis proposes a Moteino-based WSN node and an energy efficient duty cycle that reduces current consumption in standby mode using an enhanced watchdog timer. The nodes perform radio communication at 915 MHz, for short intervals (180ms) every 10 minutes, and consume 6.8 mA at -14dBm. For testing, the WSN node monitored a low-power combined air temperature, relative humidity, and barometric pressure sensor, together with a typical soil moisture sensor that consumes more power. Laboratory tests indicated average current consumption of ~30µA using these short radio transmission intervals. After transmission tests, field deployment of a star-configured network of nine of these nodes and one gateway node provides a long-term platform for testing under rigorous conditions. A webserver …

The major advantages of radio frequency identification (RFID) technology over barcodes are that the RFID-tagged objects do not require to be in line-of-sight with the reader for their identification and multiple objects can be read simultaneously. But when multiple objects are read simultaneously there is always a problem of collision which reduces the efficiency of the system. This thesis presents a comprehensive study of the dynamic framed slotted ALOHA (DFSA)-based anti-collision multi-tag identification algorithms for passive RFID system. Performance of various DFSA algorithms is compared through extensive simulation results. In addition, a number of simple performance improvement techniques have also been investigated in this thesis, including improved estimation techniques for the number of tags in each read cycle and a low-complexity heuristic stopping criterion that can be easily implemented in the practical system.

Multi band technology helps in getting multiple operating frequencies using a single microwave device. This thesis presents the design of dual and tri band microwave devices using coupled transmission line structures. Chapter 2 presents the design of a novel dual band transmission line structure using coupled lines. In chapter 3, Design of a dual band branch line coupler and a dual band Wilkinson power divider are proposed using the novel dual band transmission line structure presented in the previous chapter. In chapter 4, Design of a tri band transmission line structure by extending the dual band structure is presented. The Conclusion and future work are presented in chapter 5.

The research reported here deals with the early characterization of Parkinson’s disease (PD), the second most common degenerative disease of the human motor system after Alzheimer’s. PD results from the death of dopaminergic neurons in the substantia nigra region of the brain. Its occurrence is highly correlated with the aging population whose numbers increase with the healthcare benefits of a longer life. Observation of motor control symptoms associated with PD, such as gait and speech analysis, is most often used to evaluate, detect, and diagnose PD. Since speech and some delicate motor functions have provided early detection signs of PD, reliable analysis of these features is a promising objective diagnostic technique for early intervention with any remedial measures. We implement and study here three PD diagnostic methods and their correlation between each other’s results and with the motor functions in subjects diagnosed with and without PD. One initial test documented well in the literature deals with feature analysis of voice during phonation to determine dysphonia measures. Features of the motor function of two fingers were extracted in tests titled “Motor function of alternating finger tapping on a computer keyboard” and “Motor function of the index and thumb finger tapping with …

This thesis presents a brief introduction to microwave components and technology. It also presents two novel dual-band designs, their analysis, topology, simulation and fabrication. In chapter 2, a novel dual-band bandpass filter using asymmetric stub-loaded stepped-impedance resonators (SLSIRs) operating at 1 and 2.6 GHz is shown. This type of design applies suitable arrangements to improve the filter’s performance. Then, in chapter 3, a novel dual-band balun (transforms unbalanced input signals to balanced output signals or vice versa) operating at 1.1 and 2 GHz with flexible frequency ratios is presented, which has more advantages in microwave applications. Then, conclusion and future works are discussed in chapter 4.

Deep reinforcement learning is an area of research that has blossomed tremendously in recent years and has shown remarkable potential in computer games. Real-time strategy game has become an important field of artificial intelligence in game for several years. This paper is about to introduce a kind of algorithm that used to train agents to fight against computer bots. Not only because games are excellent tools to test deep reinforcement learning algorithms for their valuable insight into how well an algorithm can perform in isolated environments without the real-life consequences, but also real-time strategy games are a very complex genre that challenges artificial intelligence agents in both short-term or long-term planning. In this paper, we introduce some history of deep learning and reinforcement learning. Then we combine them with StarCraft. PPO is the algorithm which have some of the benefits of trust region policy optimization (TRPO), but it is much simpler to implement, more general for environment, and have better sample complexity. The StarCraft environment: Blood War Application Programming Interface (BWAPI) is open source to test. The results show that PPO can work well in BWAPI and train units to defeat the opponents. The algorithm presented in the thesis is …

Computer hardware and algorithm design have seen significant progress over the years. It is also seen that there are several domains in which humans are more efficient than computers. For example in image recognition, image tagging, natural language understanding and processing, humans often find complicated algorithms quite easy to grasp. This thesis presents the different case studies to learn human mapping strategy to solve the mapping problem in the area of coarse-grained reconfigurable architectures (CGRAs). To achieve optimum level performance and consume less energy in CGRAs, place and route problem has always been a major concern. Making use of human characteristics can be helpful in problems as such, through pattern recognition and experience. Therefore to conduct the case studies a computer mapping game called UNTANGLED was analyzed as a medium to convey insights of human mapping strategies in a variety of architectures. The purpose of this research was to learn from humans so that we can come up with better algorithms to outperform the existing algorithms. We observed how human strategies vary as we present them with different architectures, different architectures with constraints, different visualization as well as how the quality of solution changes with experience. In this work all …

Semiconductor nanowires acts as an emerging class of materials with great potential for applications in future electronic devices. Small size, large surface to volume ratio and high carrier mobility of nanowires make them potentially useful for electronic applications with high integration density. In this thesis, the focus was on the growth of high quality ZnO nanowires, fabrication of field effect transistors and UV- photodetectros based on them. Intrinsic nanowire parameters such as carrier concentration, field effect mobility and resistivity were measured by configuring nanowires as field effect transistors. The main contribution of this thesis is the development of a high gain UV photodetector. A single ZnO nanowire functioning as a UV photodetector showed promising results with an extremely high spectral responsivity of 120 kA/W at wavelength of 370 nm. This corresponds to high photoconductive gain of 2150. To the best of our knowledge, this is the highest responsivity and gain reported so far, the previous values being responsivity=40 kA/W and gain=450. The enhanced photoconductive behavior is attributed to the presence of surface states that acts as hole traps which increase the life time of photogenerated electrons raising the photocurrent. This work provides the evidence of such solid states and preliminary …

The baluns are the key components in balanced circuits such balanced mixers, frequency multipliers, push–pull amplifiers, and antennas. Most of these applications have become more integrated which demands the baluns to be in compact size and low cost. In this thesis, a new approach about the design of planar balun is presented where the 4-port symmetrical network with one port terminated by open circuit is first analyzed by using even- and odd-mode excitations. With full design equations, the proposed balun presents perfect balanced output and good input matching and the measurement results make a good agreement with the simulations. Second, Yagi-Uda antenna is also introduced as an entry to fully understand the quasi-Yagi antenna. Both of the antennas have the same design requirements and present the radiation properties. The arrangement of the antenna’s elements and the end-fire radiation property of the antenna have been presented. Finally, the quasi-Yagi antenna is used as an application of the balun where the proposed balun is employed to feed a quasi-Yagi antenna. The antenna is working in the S-band radio frequency and achieves a measured 36% fractional bandwidth for return loss less than -10 dB. The antenna demonstrates a good agreement between its measurement …