This work includes two unrelated areas of research. The first portion of this work involved combusting densified refuse derived fuel (dRDF) with coal and studying the effect that Ca(0H)2 binder had on reducing polycyclic aromatic hydrocarbon (PAH) and polychlorinated biphenyl (PCB) emissions. The second area of work was directed at developing nondestructive infrared techniques in order to aid in the analysis of postage stamp adhesives. With Americans generating 150-200 million tons a year of Municipal Solid Waste (MSW) and disposing of nearly ninety percent of it in landfills, it is easy to understand why American landfills are approaching capacity. One alternative to landfilling is to process the MSW into RDF. There are technical and environmental problems associated with RDF. This work provides some answers concerning the amount of PAH and PCB emissions generated via the combustion of RDF with coal. It was found that the Ca(OH)2 binder greatly reduced both the PAH and the PCB emissions. In fact, PAH emissions at the ten-percent level were reduced more by using the binder than by the pollution control equipment. If the Ca(0H)2 binder can reduce not only PAH and PCB emissions, but also other noxious emissions, such as acid gases or dioxin, …

Thermal and flash photolysis studies of ligand-substitution reactions of cis-(pip)(L)M(CO)_4 by L' (pip = piperidine; L, L' = CO, phosphines, phosphites; M = Cr, Mo) implicate square-pyramidal [(L)M(CO)_4], in which L occupies a coordination site in the equatorial plane, as the reactive species. In chlorobenzene (= CB) solvent, the predominant species formed after flash photolysis and a steady-state intermediate for the thermal reaction is cis—[(CB)(L)M(CO)_4], for which rates of CB-dissociation increase with increasing steric demands of coordinated L. Rates of CB-dissociation from trans-[(CB)(L)M(CO)_4] intermediates, formed after photolysis but not thermally, exhibit no observable dependence on the steric properties of the coordinated L.

The aim of the investigation described in this work is to gain a better understanding of the processes involved in the oxidation of organic compounds by photolytic ozonation in a laboratory scale reactor. The results and discussions are presented in Chapter III. This chapter contains four parts. In the first part, mass transfer efficiency and the calculation of the mass transfer coefficient, KLa, as well as the ozone decomposition rate constant, KD, are presented and compared with those obtained by other investigators. The second part deals with the kinetics of the photolysis of 2,2',4,4',6,6'-hexachlorobiphenyl both in purified and natural lake water. Mathematical expressions and a discussion of the possible reaction processes involved are given. Kinetic models of ozonation and photolytic ozonation in purified and natural lake water are developed and discussed in part three. Rate constants are calculated from experimental data and used to predict values of substrate destruction with a mathematical model. The fourth part of this chapter deals with the identification of products from the photolysis, ozonation and photolytic ozonation of 2,2'4,4',6,6'-hexachlorobiphenyl. The products are isolated and identified using combined gas chromatography and mass spectroscopy, and reaction mechanisms are suggested.

The objective of this study was to synthesize and characterize new energetic polycyclic "cage" compounds. As part of a program involved in the synthesis of new polynitropolycyclic compounds, 2,6-dinitro-5-methoxy- 7-carbomethoxypentacyclo[5. 3 .0 . 0* • * . CP • i ° . 0* •8]decane has been synthesized. This is a model system which can be used to study (1) the effect of nitro substitution on the photolability of carbon-carbon double bonds and (2) to develop methods for avoiding Haller-Bauer cleavage in cage /3-keto esters when synthesizing polynitro-substituted cage compounds.

Pulsed laser time-resolved ligand-substitution photochemistry for (DTO)W(CO)4, (DTN)W(CO)4, and (NP)Mo(CO)4 (DTO = 2,2,7,7-tetramethyl-3,6-diathiaoctane; DTN = 2,2,8,8- tetramethyl-3,7-diathianonane; NP = l-diethylamino-2- diphenylphosphinoethane) proceeds via initial fission of the W-S and Mo-P bonds, affording Cs and C4v five-coordinate intermediates for DTN and NP but largely Cs for DTO. The rates of reaction of these intermediates, via chelate ring closure and competitive bimolecular interaction with Lewis bases (= L, alkylphosphines and alkyl phosphites) for the Cs intermediates and via bimolecular interaction of L with the C4v intermediates, together with activation parameters for these processes have been determined. The rates of interactions at the Cs intermediates are significantly faster than at the C4v intermediates.

The first objective of this investigation was to conduct a systematic study into the reactions of chloroketenes with ketene acetals. The second objective was to explore the synthetic utility of these reaction products and offer a rational explanation for these reaction products.

The objective of this study was to synthesize new energetic, strained, saturated polycyclic compounds. For this purpose, new methodology has been developed, as follows: (i) Ketenes have been generated in situ via treatment of aldo-, keto- or alkenoic acid with either toluenesulfonyl chloride or 2-chloro-1-methylpyridfniurn iodide (Mulkaiyama's reagent). The reactive intermediates thereby generated have been found to undergo intramolecular [2+2] cycloaddition reactions in these systems.

The problem with which this research is concerned is the determination of inorganic anions and cations with single injection ion chromatography. Direct detection of the separated analyte ions occurs after the analyte ions have passed through ion-exchange resins where they are separated according to their affinity for the ion-exchange resin active sites. The techniques involve the use of essentially a non-suppressed ion chromatographic system followed by a suppressed ion chromatographic system. With this system it is possible to accomplish both qualitative and quantitative determinations.

Ion chromatography (IC) as developed by Small et. al. in 1975 has become an efficient and reliable analytical technique for simultaneous analysis of multiple ions in solution. The principle requirement prior to use the IC for an analysis is sample preparation; these include sample decomposition, solvent extraction, and trapping in case the target element is in the gas phase, etc. Solvent extractions for fluoride, chloride, sodium, ammonium, and potassium ions which are soluble in soils are described. Sample decompositions include silicate rocks using hydrofluoric acid for the determination of phosphorus; organic pesticides using lithium fusion technique for the determination of halide and cyanide ions are also described. After these sample preparation techniques, the aqueous solutions obtained were analyzed on the ion chromatograph for the analyses of the anions and cations mentioned above. Recovery and reproducibility of each technique is in general quite good and the comparison between the results obtained from the IC method and other instrumentation are given.

Certain ligand substitution reactions proceed to a complete displacement of the chelate ligand. Certain reactions proceed through a mechanism involving an initial fission of the tungsten-sulfur bond to afford a coordinatively-unsaturated intermediate which is rapidly attacked by chlorobenzene. The resulting solvated intermediate establishes an equilibrium which involves desolvation-solvation. Although main group organometallic chemistry has received a great deal of attention, this discussion will be centered in organotransition metal chemistry, in particular, metal carbonyls.

One objective of this study was to explore the intramolecular [2+2] cycloadditions of phenoxyketenes to carbonyl groups with isoflavones and benzofurans as target compounds. The other objective was to investigate the eyeloaddition reactions of rarely studied aminoketenes. The conversion of 2-(carboxyalkoxy)benzils to the corresponding phenoxyketenes leads to an intramolecular [2+2] cycloaddition to ultimately yield isoflavones and/or 3-aroylbenzofurans. The product distributions are dependent upon the substitution pattern in the original benzil acids. The initial cycloaddition products, β-lactones, are isolated in some instances while some β-lactones spontaneously underwent decarboxylation and could not be isolated. The ketene intermediate was demonstrated in the intramolecular reaction of benzil acids or ketoacids with sodium acetate and acetic anhydride. It is suggested that sodium acetate and acetic anhydride could serve as a source for the generation of ketenes directly from certain organic acids. The treatment of ketoacids with acetic anhydride and sodium acetate provides a simpler procedure to prepare benzofurans than going through the acid chloride with subsequent triethylamine dehydrochlorination to give the ketenes. N-Ary1-N-alkylaminoketenes were prepared for the first time from the corresponding glycine derivatives by using p-toluenesulfonyl chloride and triethylamine. These aminoketenes underwent in situ cycloadditions with cyclopentadiene, cycloheptene and cyclooctenes to yield only the …

When E- or Z-l-methyl-l-phenyl-2-neopentylsilene was generated by the retro-Diels-Alder vacuum-sealed tube thermolysis of its corresponding anthracene adduct, in the presence of various alkoxysilanes, only one diastereomeric adduct was formed in each case, showing that the reactions are stereospecific. An x-ray crystal structure of the methoxytriphenylsilane adduct of the E-silene confirmed its relative configuration as (R,S) or (S,R). This demonstrated that the addition of alkoxysilanes to silenes is stereospecific and syn. The relative configurations of similar alkoxysilane and alkoxystannane adducts to E- and Z-l-methyl-l-phenyl-2-neopentylsilene were assigned based on a combination of xray structures and *3C NMR data. A strong, nonbonded oxygen-metal interaction is apparent in all of those compounds studied. Treatment of the alkoxystannane adducts with alkyl lithium reagents results in tin-lithium exchange in some cases. The results indicate that the resulting <x-lithio alkoxysilanes are not configurationally stable in either THF or hydrocarbon solvents. The reaction of tert butyl lithium with a-trimethylsilylvinylmethylphenylchlorosilane in hydrocarbon solvents yields E- and Z-l-methyl-l-phenyl-2-neopentyl-2-trimethylsilylsilene. In the absence of any traps these silenes undergo a novel tert butyl lithium catalyzed rearrangement to 2-phenyl-3-trimethylsilyl-5,5-dimethyl-2-silahex-3-ene. These silenes were also trapped as their [4+2] cycloadducts with anthracene. The Z-isomer of the anthracene adduct was separated and its stereochemistry confirmed by …

A method has been developed for the rapid, quantitative separation of normal and abnormal phosphoglucose isoemrase allozymes from individuals heterozygous for genetic variant forms of the enzyme. The method utilizes a substrate gradient elution of the enzyme from carboxymethyl Biogel and is far superior in terms of resolution and recovery to methods based on electrophoresis and isoelectric focusing. Four different genetic variant forms of the enzyme were isolated and subjected to a systematic comparison of their physical, catalytic and stability properties. The physical and catalytic properties of the variants were similar; however, clear differences in the stability of the allozymes were apparent.

Six bis(silyl)acetylenes with the following varied silicon substituents were prepared: I (Me, Me); II (H, H); III (Cl, H); IV (Cl, Cl); V (OMe, H); VI (OMe, OMe). While I and II may be prepared by the reaction of dilithio- or bis(bromomagnesium)-acetylide with appropriate chlorosilane, similar reactions designed to give III - VI give oligomers, YMe_2Si(C≡C-SiMe_2)_nY, VII, Y = Cl, OMe, as the major products indicating that the acetylenic functionality on silicon activates the chlorosilane toward nucleophilic substitution. Compounds III and IV were prepared by free radical chlorination of II. Methanolysis of III and IV gave quantitative yields of V and VI, respectively. In the presence of mineral acid, VI readily cyclized to give high yields of the cyclic siloxane octamethyl-4,9-dioxa-3,5,8,10-tetrasila-cyclodeca-1,6-diyne, VIII, and the analogous triyne, IX. It was determined that V and VI could be prepared directly from II in high yield by methanolysis with palladium catalyst. Vaska's complex also accomplished the conversion. I attempted to prepare bis(ethoxydimethylsilyl)acetylene by using of Wilkinson 's catalyst for hydrosilylation with acetaldehyde. The principal product of this reaction was 1-(dimethylsilyl)-3,5,5-trimethyl-4-oxa-3-silacyclopent-1-ene, XI.

A variable temperature ^13 C and ^199 Hg NMR study has been conducted for diphenyl-, bis(o-tolyl)-, bis(m-tolyl)-, and bis(2, 6-xylyl)mercury in dimethyl sulfoxide and 1,1,2,2 tetrachloroethane; ^13 C T1 relaxation times are reported as a function of temperature. Barriers to rotation of the aryl rings are obtained. Chemical shifts and couplings in CDCl_3 are given for bis(p-tolyl)-, bis(2, 5-xylyl)-, bis(mesityl)-,phenyl(o-tolyl)-, phenyl(m-tolyl)mercury, and the compounds listed above. The steric interactions of these aryl mercury compounds are discussed.

The structures of Diels-Alder cycloaddition of cyclopentadiene to 2,6-dimethyl-p-benzoquinone and methylcyclopentadiene to 2,6-dimethyl-p-benzoquinone were assigned by analysis of 1-D and 2-D proton and carbon-13 NMR spectra. The structures of the cycloadduct of methylcyclopentadiene to 2,6-dimethyl-p-benzoquinone and that of the corresponding intramolecular [2+2] photocyclization product were also obtained by single crystal X-ray structural analysis. As the second part of the study, a new polycyclic "cage" molecule, a substituted trishomocubane isomer, was synthesized. In this synthesis, reductive bond cleavage followed by Dieckmann condensation was employed. Wolff-Kishner reduction then was used to convert a β-keto ester "cage" molecule to the corresponding carboxylic acid. A compound that possesses twofold symmetry was isolated from reaction product mixture. The structure of this compound has been established by single crystal X-ray crystallography.

The temperature-dependent catalytic activity of rat liver 3-hydroxy-3 -methylglutaryl coenzyme A reductase (HMG-CoA reductase) displays the nonlinear Arrhenius behavior characteristic of many membrane-bound enzymes. A two-conformer equilibrium model has been developed to characterize this behavior. In the model, HMG-CoA reductase undergoes a conformational change from a low specific activity to a high specific activity form. This conformation change is apparently driven by a temperature-dependent phase transition of the membrane lipids. It has been found that this model accurately describes the data from diets including rat chow, low-fat, high-carbohydrate, and diets supplemented with fat, cholesterol or cholestyramine. The effects characterized by the model are consistent with the regulation of HMG-CoA reductase by enzyme-lipid interactions.

The substitution reaction of (DTN)W2 (CO)10 with P(OCH(CH3 )2 )3 is a stepwise reaction. The kinetics of step 1 follow the equation: -d[substrate] /dt = kld [substrate] + k la [substrate] [ligand]. Thus the mechanism of step 1 is expected to be a competition between dissociative and associative pathways. The kinetics of step 2 follow the equation: -d[(DTN)W(CO)5]/dt = k2dk3[(DTN)W(CO)5][ligand]/k-2[DTN] + k3[ligand] The plot of kobsd versus [ligand] thus is a hyperbolic curve and the plot of 1/kobsd versus 1/[L] exhibits linear behavior. A mechanism for step 2 in which (DTN)W(CO)5 dissociates to an intermediate, W(CO) 5 , and in which DTN and P(OCH(CH3 )2 )3 compete to associate with W(CO) 5 is favored. The dissociative rate constant of the first step, kld' is about 1.2 times of that of the second step, k2d. The dissociation of (DTN)W(CO) 5 from (DTN)W2 (CO) 1 0 is favored over the dissociation of DTN from (DTN)W(CO) 5 due to a combination of the steric, stoichiometric, charge repulsion and entropy effects of the reaction.

Trihalomethanes such as chloroform, dichlorobromomethane, dibromochloromethane, and bromoform are formed when natural water is chlorinated in water treatment. This investigation explores the use of ozone to remove organic precursors from natural water, thus decreasing trihalomethane formation potential. The data suggest a mechanism involving formation of secondary precursors after prolonged contact with ozone, suggesting that trihalomethane precursors may be minimized by using low doses of ozone and short contact time.

The Raman linewidths of the carbon-halogen stretching mode was measured as a function of temperature in ethyl bromide, isopropyl chloride, isopropyl bromide, t-butyl chloride, t-butyl bromide, chlorobenzene, bromobenzene, iodobenzene and o-dichlorobenzene. The vibrational relaxation times showed a very clear trend. Together with earlier work on methyl iodide, these results provide evidence that the vibrational dephasing efficiencies (T^-1_iso) of the carbon-halogen mode vary in the order of Cl > Br > I. Vibrational dephasing times were calculated from the Fischer-Laubereau Isolated Binary Collision Mode. If further work shows this transferability to extend to other types of skeletal modes in molecular systems, this would have significant ramifications on future vibrational lineshape studies.

Huian plasma high-density lipoprotein (HDL) were isolated by a procedure employing polyanion precipitation and column chromatography. Lipid and protein composition of the HDL isolated by this method was found to be similar to another HDL preparation isolated by ultracentrifugation. However, minor differences were noted, including a higher phospholipid and apoproteinE content and lower triglyceride content of the HDL isolated by column chromatography. Four subfraction of HDL were obtained following chromatography on an anion exchange column. The subfraction four had the highest esterified to free cholesterol ratio, the second highest phospholipid to unesterified cholesterol, and the lowest molecular weight. In addition it was consistently coincided with lecithin: cholesterol acyltransferase (LCAT) activity and found to be the best substrate for the enzyme.

The objectives of these investigations were (1) the purification of MG reductase from sheep liver and (2) studies of some of its characteristics. MG reductase was purified 40 fold and showed a single band on SDS-PAGE. Molecular weight estimations with SDS-PAGE showed a molecular weight of 44,000; although gel filtration with Sephadex G-150 gave a molecular weight of 87,000 indicating that the enzyme might be a dimer. The Km for MG is 1.42 mM and for NADH it is 0.04 mM. The pH optimum for the purified enzyme is pH 7.0. Isoelectric focusing experiments showed a pI of 9.3. In vivo experiments involving rats treated with 3,3',5-triiodothyronine (T_3) and 6-n-propyl-2-thiouracil (PTU) indicated that MG reductase was depressed by T_3 and elevated by PTU.

A new, efficient route was used in the synthesis of [2.2]-paracyclophane-2-carboxylic acid. The acid as then resolved and the Birch reduction performed yielding one enantiomer of tetrahydro-[2.2]-paracyclophane-2-carboxylic acid. The ultraviolet spectrum of tetrahydro-[2.2]-paracyclophane- 2-carboxylic acid in isopenthane shows one absorption at 206 nm (Emax = 5,271). There are three bands observed in the circular dichroism spectrum in isopentane at 236 nm ([] = 1.8 X 104), 201 nm ([0] = -16 X 104) and a positive band indicated below 180 nm but not observed. The bands were assigned and possible reasons for the occurrence of a mr'r* transition at unexpectedly long wavelengths are discussed.

Two adsorption/microcoulometric methods have been investigated for total organic halogen (TOX) in water. TOX, a proposed water-quality parameter, is a rapid, surrogate method to detect halides microcoulometrically and does not require compound identification before water quality can be judged. An XAD resin is used to concentrate organic halides that are eluted by a two-step, two-solvent procedure, followed by analysis using :chromatography or pyrolysis to convert organic halides to halide. In the granular activated carbon (GAC) method, the entire GAC-organic halide sample is pyrolyzed. TOX measurements of model compounds are comparable by both methods, but GAC was found to be superior to XAD for adsorption of chlorinated humics in drinking water and chlorinated lake water.