Fluidization of biomass particles is an important process in the gasification, pyrolysis and combustion in order to extract energy from biomass. Studies on the fluidization of biomass particles (corn cob and walnut shell), inert particles (sand, glass bead, and alumina), which are added to facilitate fluidization of biomass, and biomass/sand mixture were performed. Experiments were carried out in a 14.5 cm internal diameter cold flow fluidization bed to determine minimum fluidization velocities with air as fluidizing medium. On the of basis of experimental data from both present work and those found in the literature, new correlations were developed to predict minimum fluidization velocity for inert particles as well as biomass particles. It was found that the proposed correlations satisfactorily predict minimum fluidization velocities and was in well agreement with experimental data. Furthermore, effect of weight percentage of biomass in the biomass/sand mixtures was studied. The weight fraction of biomass particles in the mixture was chosen in the range of 0 ~ 100 wt. %. The results show that minimum fluidization velocity of the mixtures increases with an increase in biomass content. Using the present experimental data, a new correlation was developed in terms of mass ratio for predicting values of …

Dallas is the third largest growing industrialized city in the state of Texas. the prevailing air quality here is highly influenced by the industrialization and particulate matter 2.5µm (PM2.5) has been found to be one of the main pollutants in this region. Exposure to PM2.5 in elevated levels could cause respiratory problems and other health issues, some of which could be fatal. the current study dealt with the quantification and analysis of the sources of emission of PM2.5 and an emission inventory for PM2.5 was assessed. 24-hour average samples of PM2.5 were collected at two monitoring sites under the Texas Commission on Environmental Quality (TCEQ) in Dallas, Dallas convention Centre (CAMS 312) and Dallas Hinton sites (CAMS 60). the data was collected from January 2003 to December 2009 and by using two positive matrix models PMF 2 and EPA PMF the PM2.5 source were identified. 9 sources were identified from CAMS 312 of which secondary sulfate (31% by PMF2 and 26% by EPA PMF) was found to be one of the major sources. Data from CAMS 60 enabled the identification of 8 sources by PMF2 and 9 by EPA PMF. These data also confirmed secondary sulfate (35% by PMF2 and …

Texas is the second largest state in U.S.A. based on geographical area, population and the economy. It is home to several large coastal urban areas with major industries and infrastructure supporting the fossil-fuel based energy sector. Most of the major cities on the state have been impacted by significant air pollution events over the past decade. Studies conducted in the southern coastal region of TX have identified long range transport as a major contributor of particulate matter (PM) pollution along with local emissions. Biomass burns, secondary sulfates and diesel emissions sources are comprise as the dominant mass of PM2.5 have been noted to be formed by the long range transport biomass from Central America. Thus, the primary objective of this study was to identify and quantify local as well as regional sources contributing to the PM pollution in the coastal area of Brownsville located along the Gulf of Mexico. Source apportionment techniques such as principal component analysis (PCA) and positive matrix factorization (PMF) were employed on the air quality monitoring data to identify and quantify local and regional sources affecting this coastal region. As a supplement to the PMF and PCA, conditional probability function (CPF) analysis and potential source contribution …

Commercial aviation is a vital part of the United States economy. It generates over $1 trillion annually, which is more than 5% of the U.S. GDP, and produces approximately 10 million jobs. Every year there is an increase in commercial air traffic. This is attributed to expanding trade between states and other countries, which requires larger amounts of cargo aircraft in operation, and also catering to the growing number of middle and upper class passengers who travel for business and pleasure purposes. A rise in commercial aviation leads to the use of more aviation fuel on a monthly and annual basis. This in turn leads to escalated levels of combustion by-products from jet and turbofan engines into the atmosphere. The negative effects of these by-products range from producing poor air quality and consequent health hazards to contributing to global warming. This study is aimed at assessing the impacts of aircraft emissions on the local air quality in Corpus Christi using the Emissions and Dispersion Modeling System. Flight data for the study was obtained from the Department of Transportation's Research and Innovative Technology Administration. Analyses of the emissions were compared on monthly, annual, engine type and airline provider bases. Climatic, economic …

Different ways to measure human affective and deceptive reactions to stimulus have been developed. One method is a multimodal approach using web camera, thermal imaging camera and physiological sensors data to extract different features in the human face (verbal and non-verbal behavior) such as breathing rate, heart rate, face temperature, skin conductance, eye tracking, language analysis and facial expressions among others. Human subjects from different ages and ethnicity were exposed to two different experiments were they watched videos (affection recognition) and others answered an interview session (deception recognition). With the data collected from videos (thermal and visual), different regions of interest (ROI) of the face were selected as well as the whole picture. The ROI were determined based on the most sensitive parts of the face where larger changes of temperature or other physiological features are recorded. It was also analyzed the language (written and spoken) in order to obtain the verbal modalities. The data has been compared among the subjects to determine whether the deceptive and affective reactions of a person can be predicted using multimodal approach. From the multiple data obtained, a characterization of reactions is proposed when subjects are exposed to different stimulus, positive or negative, as …

Electrospinning has been recognized as an efficient technique for the fabrication of polymer fibers. These electrospun fibers have many applications across a broad range of industries. In this research, optical transparent composites were successfully fabricated by embedding polyacrylonitrile (PAN) hollow nanofibers into poly (methyl methacrylate) (PMMA) matrix. The hollow PAN nanofibers were prepared by coaxial electrospinning. The PAN was used as the shell solution, and the mineral oil was used as the core solution. The resulting fibers were then etched with octane to remove the mineral oil from the core. The hollow PAN fibers were then homogeneously distributed in PMMA resins to fabricate the composite. The morphology, transmittance and mechanical properties of the PAN/PMMA composite were then characterized with an ESEM, TEM, tensile testing machine, UV-vis spectrometer and KD2 Pro Decagon device. The results indicated that the hollow nanofibers have relatively uniform size with one-dimensional texture at the walls. The embedded PAN hollow nanofibers significantly enhanced the tensile stress and the Young's modulus of the composite (increased by 58.3% and 50.4%, respectively), while having little influence on the light transmittance of the composite. The KD2 Pro device indicated that the thermal conductivity of the PMMA was marginally greater than the …

Thermal transport behavior of austenite stainless steel stripe (304) and the carbon nano-tubes (CNTs) films of varying thickness are studied using a micropipette thermal sensor. Micropipette sensors of various tip sizes were fabricated and tested for the sensitivity and reliability. The sensitivity deviated by 0.11 for a batch of pipette coated under same physical vapor deposition (PVD) setting without being affected by a tip size. Annealing, rubber coating and the vertical landing test of the pipette sensor proved to be promising in increasing the reliability and durability of the pipette sensors. A micro stripe (80µm × 6µm × 0.6µm) of stainless steel, fabricated using focused ion beam (FIB) machining, was characterized whose thermal conductivity was determined to be 14.9 W/m-K at room temperature. Similarly, the thermal characterization of CNT films showed the decreasing tendency in the thermal transport behavior with the increase in the film thickness.

TSDC (thermally stimulated depolarization current) is one of the most important and popular technique for investigating electret materials. TSDC technique can indicate the magnitude of polarization and depolarization, relaxation time, charge-storage, glass transition, and activation energy. To fully investigate polarization and relaxation for pure epoxy and filled epoxy materials, a TSDC system was built and verified by the research. The article describes the building processes and verification of the TSDC system. TSDC, TSPC, and TWC tests data for epoxy and filled epoxy samples are presented in the article. To compare TSDC technique with other related techniques, DEA (dielectric analysis), DMA (dynamic mechanical analysis), and DSC (differential scanning calorimetry) tests are introduced.

Corpus Christi among of the largest industrialized coastal urban areas in Texas. The strategic location of the city along the Gulf of Mexico allows for many important industries and an international business to be located. The cluster of industries and businesses in the region contribute to the air pollution from emissions that are harmful to the environment and to the people living in and visiting the area. Volatile organic compounds (VOC) constitute an important class of pollutants measured in the area. The automated gas chromatography (Auto GC) data was collected from Texas Commission of Environmental Quality (TCEQ) and source apportionment analysis was conducted on this data to identify key sources of VOC affecting this study region. EPA PMF 3.0 was employed in this sources apportionment study of measured VOC concentration during 2005 - 2012 in Corpus Christi, Texas. The study identified nine optimal factors (Source) that could explain the concentration of VOC at two urbane monitoring sites in the study region. Natural gas was found to be the largest contributor of VOC in the area, followed by gasoline and vehicular exhaust. Diesel was the third highest contributor with emissions from manufacturing and combustion processes. Refineries gases and evaporative fugitive emissions …

Poor air quality can greatly affect the public health. Research studies indicate that indoor air can be more polluted than the outdoor air. An indoor air quality monitoring system will help to create an awareness of the quality of air inside which will eventually help in improving it. The objective of this research is to develop a low cost wireless sensor system for indoor air quality monitoring. The major cost reduction of the system is achieved by using low priced sensors. Interface circuits had to be designed to make these sensors more accurate. The system is capable of measuring carbon dioxide, carbon monoxide, ozone, temperature, humidity and volatile organic compounds. The prototype sensor node modules were developed. The sensor nodes were the connected together by Zigbee network. The nodes were developed in such a way that it is compact in size and wireless connection of sensor nodes enable to collect air quality data from multiple locations simultaneously. The collected data was stored in a computer. We employed linear least-square approach for the calibration of each sensor to derive a conversion formula for converting the sensor readings to engineering units. The system was tested with different pollutants and data collected was …

In the past decade, the condensation on superhydrophobic surfaces has been investigated abundantly to achieve dropwise condensation. There is not a specific approach in choosing the size of the roughness of the superhydrophobic surfaces and it was mostly selected arbitrarily to investigate the behavior of condensates on these surfaces. In this research, we are optimizing the size of the roughness of the superhydrophobic surface in order to achieve dropwise condensation. By minimizing the resistances toward the transition of the tails of droplets from the cavities of the roughness to the top of the roughness, the size of the roughness is optimized. It is shown that by decreasing the size of the roughness of the superhydrophobic surface, the resistances toward the transition of the tails of droplets from Wenzel state to Cassie state decrease and consequently dropwise condensation becomes more likely.

In several areas around the world, clean water is a precious asset that at anytime, and mainly due to circumstances of weather and climate, can become scarce. Mainly in the dry and remote places, people suffer with lack of water. A solution for this suffering can be a water desalination system, which makes water potable and usable for industry. That solution inherently, brings the problem of power requirement, which is sometimes arduous to accomplish in such remote areas of difficult access and long distances to overcome to build the infrastructure required to operate an electric power plant. Texas and the USA also face this scenario for many regions, for which the government has been creating some programs and driving forward incentives, looking for solutions to support water desalination. Water desalination has future applications for municipalities water-consuming or for arid and remote regions, as well as for industries that rely on heavy water usage, such as natural gas drilling operations, for which millions of gallons are trucked overland to the site and also hauled away afterwards, when the waste water produced must be treated. This thesis created the concept of autonomy for water desalination plants replacing the actual power supply from …

A recent trend in the development of renewable and biodegradable materials has led to the development of composites from renewal sources such as natural fibers. This agricultural activity generates a large amount of waste in the form of peanut shells. The motivation for this research is based on the utilization of peanut shells as a viable source for the manufacture of biocomposites. High-density polyethylene (HDPE) is a plastic largely used in the industry due to its durability, high strength to density ratio, and thermal stability. This research focuses in the mechanical and thermal properties of HDPE/peanut shell composites of different qualities and compositions. The samples obtained were subjected to dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and mechanical tensile strength tests. TO prepare the samples for analysis, the peanut shells were separated into different mesh sizes and then mixed with HDPE at different concentrations. The results showed that samples with fiber size number 10 exhibited superior strength modulus of 1.65 GPa versus results for HDPE alone at 1.32 GPa. The analysis from the previous experiments helped to determine that the fiber size number 10 at 5%wt. ratio in HDPE provides the most optimal mechanical and thermal results. From tensile …

While many investigations have been performed to establish a better understanding of the effects that magnetic fields and nanoparticles have on cells, the fundamental mechanisms behind the interactions are still yet unknown, and investigations on concurrent exposure are quite limited in scope. This study was therefore established to investigate the biological impact of concurrent exposure to magnetic nanoparticles and extremely-low frequency magnetic fields using an in-vitro CHO-K1 cell line model, in an easily reproducible manner to establish grounds for further in-depth mechanistic, proteomic, and genomic studies. Cells were cultured and exposed to 10nm Fe3O4 nanoparticles, and DC or low frequency (0Hz, 50Hz, and 100Hz) 2.0mT magnetic fields produced by a Helmholtz coil pair. The cells were then observed under confocal fluorescence microscopy, and subject to MTT biological assay to determine the synergistic effects of these concurrent exposures. No effects were observed on cell morphology or microtubule network; however, cell viability was observed to decrease more drastically under the combined effects of magnetic field and nanoparticle exposures, as compared to independent exposures alone. It was concluded that no significant difference was observed between the types of magnetic fields, and their effects on the nanoparticle exposed cells, but quite clearly there are …

The Barnett shale basin, the largest onshore gas field in the state of Texas, mainly produces natural gas. The basin’s oil and gas productions have dramatically increased over the past two decades with the enhancement via shale fracturing (fracking) technology. However, recent studies suggest that air emissions from shale fracking have significantly contributed to the growing air pollution problem in North Texas. In this study, air emissions from the Barnett shale basin during the production phase of the oil and gas activities (once the product is collected from the wells) are quantified. Oil and gas production data were acquired from the Texas Railroad Commission for the baseline years of 2010 through 2013. Methodology from prior studies on shale basins approved by the Texas Commission on Environmental Quality was employed in this study and the emission inventories from the production phase sources were quantified. Accordingly, the counties with the most gas operations in the basin, Tarrant, Johnson, Denton and Wise, were found to be the highest emitters of air pollutants. Tarrant County was responsible for the highest emitted NOx (42,566 tons) and CO (17,698 tons) in the basin, while Montague County released the maximum VOC emissions (87,601 tons) during the study …

Cellular materials, often called lattice materials, are increasingly receiving attention for their ultralight structures with high specific strength, excellent impact absorption, acoustic insulation, heat dissipation media and compact heat exchangers. In alignment with emerging additive manufacturing (AM) technology, realization of the structural applications of the lattice materials appears to be becoming faster. Considering the direction dependent material properties of the products with AM, by directionally dependent printing resolution, effective moduli of lattice structures appear to be directionally dependent. In this paper, a constitutive model of a lattice structure, which is an octet-truss with a base material having an orthotropic material property considering AM is developed. In a case study, polyjet based 3D printing material having an orthotropic property with a 9% difference in the principal direction provides difference in the axial and shear moduli in the octet-truss by 2.3 and 4.6%. Experimental validation for the effective properties of a 3D printed octet-truss is done for uniaxial tension and compression test. The theoretical value based on the micro-buckling of truss member are used to estimate the failure strength. Modulus value appears a little overestimate compared with the experiment. Finite element (FE) simulations for uniaxial compression and tension of octet-truss lattice materials …

This thesis aims to develop a new type of highly stretchable strain sensor to measure large deformation of a specimen subjected to dynamic loading. The sensor was based on the piezo-resistive response of carbon nanotube(CNT)/polydimethysiloxane (PDMS) composites thin films, some nickel particles were added into the sensor composite to improve the sensor performance. The piezo-resistive response of CNT composite gives high frequency response in strain measurement, while the ultra-soft PDMS matrix provides high flexibility and ductility for large strain measuring large strain (up to 26%) with an excellent linearity and a fast frequency response under quasi-static test, the delay time for high strain rate test is just 30 μs. This stretchable strain sensor is also able to exhibit much higher sensitivities, with a gauge factor of as high as 80, than conventional foil strain gauges.

Self-activation is a process that takes advantage of the gases emitted from the pyrolysis process of biomass to activate the converted carbon. The pyrolytic gases from the biomass contain CO2 and H2O, which can be used as activating agents. As two common methods, both of physical activation using CO2 and chemical activation using ZnCl2 introduce additional gas (CO2) or chemical (ZnCl2), in which the CO2 emission from the activation process or the zinc compound removal by acid from the follow-up process will cause environmental concerns. In comparison with these conventional activation processes, the self-activation process could avoid the cost of activating agents and is more environmentally friendly, since the exhaust gases (CO and H2) can be used as fuel or feedstock for the further synthesis in methanol production. In this research, many types of biomass were successfully converted into activated carbon through the self-activation process. An activation model was developed to describe the changes of specific surface area and pore volume during the activation. The relationships between the activating temperature, dwelling time, yield, specific surface area, and specific pore volume were detailed investigated. The highest specific surface area and pore volume of the biomass-derived activated carbon through the self-activation process …

Conventional sources of emissions have been a prime target for policymakers in designing pollution control strategies. However, the evolution of shale gas activities is a growing concern over the impact of unconventional sources on urban and regional air quality. Owing to the development of Barnett Shale production, the fast-growing Dallas-Fort Worth (DFW) metroplex has encountered both types of these emissions. Oil and gas activities result in emissions of ozone precursors, notably volatile organic compounds (VOC). The major objective of this study was to evaluate the spatio-temporal distribution of VOC in order to highlight the influence of unconventional emissions. The study utilized measurements from automated gas chromatography (AutoGC) monitors to analyze the patterns of the total non-methane organic compounds (TNMOC) and relative contributions from marker species of traffic versus oil and gas activities. In this study, data from 2001-2014 was obtained from the Texas Commission on Environmental Quality (TCEQ) for fifteen monitoring sites within the North Texas region. With over a thousand wells in a 10 mile radius, two of the rural sites measured twice as much TNMOC as compared to the urban site in Dallas. Source apportionment analysis was conducted using Positive Matrix Factorization (PMF) technique. The target site located …

Hierarchical arrangement of biological composites such as nacre and bone containing high filler (ceramic) content results in high strength and toughness of the natural material. In this study we mimic the design of layered bone microstructure and fabricate an optimal multifunctional bio-nanocomposite having strength, toughness and corrosion resistance. Poly (butylene adipate-co-terephthalate) (PBAT), a biodegradable polymer was used as a substrate material with the reinforcement of LDH (Layered double hydroxide) as a nanofiller in different concentrations to achieve enhancement in mechanical properties as well as processing related thermostability. Corrosion resistance was increased by mimicking a layered structured which incorporated a tortuous diffusion path.

Semiconductor die attach materials for high voltage, high reliability analog devices require high thermal conductivity and retention of dielectric strength. A comparative study of effective thermal conductivity and dielectric strength of selected thermoset/ceramic composites was conducted to determine the effect of ceramic particle size and ceramic particle loading on thermoset polymers. The polymer chosen for this study is bismaleimide, a common aerospace material chosen for its strength and thermal stability. The reinforcing material chosen for this study is a ceramic, hexagonal boron nitride. Thermal conductivity and dielectric breakdown strength are measured in low and high concentrations of hexagonal boron nitride. Adhesive fracture toughness of the composite is evaluated on copper to determine the composite’s adhesive qualities. SEM imaging of composite cross-sections is used to visualize particle orientation within the matrix. Micro-indentation is used to measure mechanical properties of the composites which display increased mechanical performance in loading beyond the percolation threshold of the material. Thermal conductivity of the base polymer increases by a factor of 50 in 80%wt loading of 50µm hBN accompanied by a 10% increase in composite dielectric strength. A relationship between particle size and effective thermal conductivity is established through comparison of experimental data with an empirical …

The effect of shale gas activities on ground-level ozone pollution in the Dallas-Fort Worth area is studied in detail here. Ozone is a highly reactive species with harmful effects on human and environment. Shale gas development, or fracking, involves activities such as hydraulic fracturing, drilling, fluid mixing, and trucks idling that are sources of nitrogen oxides (NOX) and volatile organic compounds (VOC), two of the most important precursors of ozone. In this study two independent approaches have been applied in evaluating the influences on ozone concentrations. In the first approach, the influence of meteorology were removed from ozone time series through the application of Kolmogorov-Zurbenko low-pass filter, logarithmic transformation, and subsequent multi-linear regression. Ozone measurement data were acquired from Texas Commission on Environmental Quality (TCEQ) monitoring stations for 14 years. The comparison between ozone trends in non-shale gas region and shale gas region shows increasing ozone trends at the monitoring stations in close proximity to the Barnett Shale activities. In the second approach, the CAMx photochemical model was used to assess the sensitivity of ozone to the NOX and VOC sources associated with shale oil and gas activities. Brute force method was applied on Barnett Shale and Haynesville Shale emission …

Two-dimensional (2D) transition metal dichalcogenides (TMDs) show great potential for the future electronics, optoelectronics and energy applications. But, the studies unveiling their interactions with the host substrates are sparse and limits their practical use for real device applications. We report the facile nano-scratch method to determine the adhesion energy of the wafer scale MoS2 atomic layers attached to the SiO2/Si and sapphire substrates. The practical adhesion energy of monolayer MoS2 on the SiO2/Si substrate is 7.78 J/m2. The practical adhesion energy was found to be an increasing function of the MoS2 thickness. Unlike SiO2/Si substrates, MoS2 films grown on the sapphire possess higher bonding energy, which is attributed to the defect-free growth and less number of grain boundaries, as well as less stress and strain stored at the interface owing to the similarity of Thermal Expansion Coefficient (TEC) between MoS2 films and sapphire substrate. Furthermore, we calculated the surface free energy of 2D MoS2 by the facile contact angle measurements and Neumann model fitting. A surface free energy ~85.3 mJ/m2 in few layers thick MoS2 manifests the hydrophilic nature of 2D MoS2. The high surface energy of MoS2 helps explain the good bonding strength at MoS2/substrate interface. This simple adhesion …

Dynamic tensile characterization of geo-materials is critical to the modeling and design of protective structures that are often made of concrete. One of the most commonly used techniques currently associated with this type of testing is performed with a Kolsky bar and is known as the spall technique. The validity of the data from the spall technique is highly debated because the necessary boundary conditions for the experiment are not satisfied. By using a technique called pulse shaping, a new “controlled” spall technique was developed to satisfy all boundary conditions so that the analyzed data may be useful in modeling and design. The results from this project were promising and show the potential to revolutionize the way Kolsky bar testing is performed.