The following report chronicles the University of North Texas Wind Turbine Project at Apogee Stadium. The timeline of events will include the feasibility study conducted by and for the university, grant awards from the Texas State Energy Conservation Office to fund the project, and a three-year sample of real time performance data since installation. The purpose of this case study is to compare the energy generation estimates by various stakeholders to the measured energy generation using a new but uniform performance relationship. In order to optimize energy generation in wind turbine generator systems, the most common wind speeds measured at the site should also be the most efficient wind speeds at which the wind turbine can convert the kinetic energy in the wind into mechanical energy and ultimately electrical energy. The tool used to convey this relationship will be a figure plotting the wind speed profile against the efficiency curve of the wind turbine. Applying this relationship tool to the UNT Apogee Stadium wind turbines provided valuable results. The most common wind speeds at Apogee Stadium are not the most efficient wind speed for the turbine. Also, the most common wind speeds were near the lower limit of the wind …

While many investigations have been performed to establish a better understanding of the effects that magnetic fields and nanoparticles have on cells, the fundamental mechanisms behind the interactions are still yet unknown, and investigations on concurrent exposure are quite limited in scope. This study was therefore established to investigate the biological impact of concurrent exposure to magnetic nanoparticles and extremely-low frequency magnetic fields using an in-vitro CHO-K1 cell line model, in an easily reproducible manner to establish grounds for further in-depth mechanistic, proteomic, and genomic studies. Cells were cultured and exposed to 10nm Fe3O4 nanoparticles, and DC or low frequency (0Hz, 50Hz, and 100Hz) 2.0mT magnetic fields produced by a Helmholtz coil pair. The cells were then observed under confocal fluorescence microscopy, and subject to MTT biological assay to determine the synergistic effects of these concurrent exposures. No effects were observed on cell morphology or microtubule network; however, cell viability was observed to decrease more drastically under the combined effects of magnetic field and nanoparticle exposures, as compared to independent exposures alone. It was concluded that no significant difference was observed between the types of magnetic fields, and their effects on the nanoparticle exposed cells, but quite clearly there are …

The Barnett shale basin, the largest onshore gas field in the state of Texas, mainly produces natural gas. The basin’s oil and gas productions have dramatically increased over the past two decades with the enhancement via shale fracturing (fracking) technology. However, recent studies suggest that air emissions from shale fracking have significantly contributed to the growing air pollution problem in North Texas. In this study, air emissions from the Barnett shale basin during the production phase of the oil and gas activities (once the product is collected from the wells) are quantified. Oil and gas production data were acquired from the Texas Railroad Commission for the baseline years of 2010 through 2013. Methodology from prior studies on shale basins approved by the Texas Commission on Environmental Quality was employed in this study and the emission inventories from the production phase sources were quantified. Accordingly, the counties with the most gas operations in the basin, Tarrant, Johnson, Denton and Wise, were found to be the highest emitters of air pollutants. Tarrant County was responsible for the highest emitted NOx (42,566 tons) and CO (17,698 tons) in the basin, while Montague County released the maximum VOC emissions (87,601 tons) during the study …

Cellular materials, often called lattice materials, are increasingly receiving attention for their ultralight structures with high specific strength, excellent impact absorption, acoustic insulation, heat dissipation media and compact heat exchangers. In alignment with emerging additive manufacturing (AM) technology, realization of the structural applications of the lattice materials appears to be becoming faster. Considering the direction dependent material properties of the products with AM, by directionally dependent printing resolution, effective moduli of lattice structures appear to be directionally dependent. In this paper, a constitutive model of a lattice structure, which is an octet-truss with a base material having an orthotropic material property considering AM is developed. In a case study, polyjet based 3D printing material having an orthotropic property with a 9% difference in the principal direction provides difference in the axial and shear moduli in the octet-truss by 2.3 and 4.6%. Experimental validation for the effective properties of a 3D printed octet-truss is done for uniaxial tension and compression test. The theoretical value based on the micro-buckling of truss member are used to estimate the failure strength. Modulus value appears a little overestimate compared with the experiment. Finite element (FE) simulations for uniaxial compression and tension of octet-truss lattice materials …

All-aluminum microchannel heat exchangers are designed to significantly reduce refrigerant charge requirements, weight, reduced brazed joints, and decreased potential for leakage by increasing reliability. Al 3003 alloy is corrosion resistant and can be formed, welded, and brazed but the issue with all-aluminum heat exchangers is localized corrosion (pitting) in corrosive environments. Currently, there is no universally accepted corrosion test that all coil manufacturers use to characterize their products. Electrochemical testing method of cyclic polarization was employed in this investigation and relevant parameters including electrolyte corrosive agent and its concentration, electrolyte pH, and applied potential scan rate was varied to find an optimal set of parameters. Results of cyclic polarization of Al 3003 in electrolytes containing various concentrations of NaCl were compared with those of the tests in Sea Water Acidified Accelerated Test (SWAAT) electrolyte and it is shown the SWAAT electrolyte (4.2% sea salt acidified to pH of 2.9) is by far stronger (in terms of corrosivity) than typical 3.5% NaCl solution used in most corrosion testing. Corrosion rates (g/m2yr) of Al 3003 measured in this investigation were comparable to those provided by ISO 9223 standard corresponding to C1 through CX categories. Duration of cyclic polarization test is much shorter …

Fluidization of biomass particles is an important process in the gasification, pyrolysis and combustion in order to extract energy from biomass. Studies on the fluidization of biomass particles (corn cob and walnut shell), inert particles (sand, glass bead, and alumina), which are added to facilitate fluidization of biomass, and biomass/sand mixture were performed. Experiments were carried out in a 14.5 cm internal diameter cold flow fluidization bed to determine minimum fluidization velocities with air as fluidizing medium. On the of basis of experimental data from both present work and those found in the literature, new correlations were developed to predict minimum fluidization velocity for inert particles as well as biomass particles. It was found that the proposed correlations satisfactorily predict minimum fluidization velocities and was in well agreement with experimental data. Furthermore, effect of weight percentage of biomass in the biomass/sand mixtures was studied. The weight fraction of biomass particles in the mixture was chosen in the range of 0 ~ 100 wt. %. The results show that minimum fluidization velocity of the mixtures increases with an increase in biomass content. Using the present experimental data, a new correlation was developed in terms of mass ratio for predicting values of …

High entropy alloys (HEAs) are alloys with five or more principal elements. Due to these distinct concept of alloying, the HEA exhibits unique and superior properties. The outstanding properties of HEA includes higher strength/hardness, superior wear resistance, high temperature stability, higher fatigue life, good corrosion and oxidation resistance. Such characteristics of HEA has been significant interest leading to researches on these emerging field. Even though many works are done to understand the characteristic of these HEAs, very few works are made on how the HEAs can be applied for commercial uses. This work discusses the application of High entropy alloys in biomedical applications. The coronary heart disease, the leading cause of death in the United States kills more than 350,000 persons/year and it costs $108.9 billion for the nation each year in spite of significant advancements in medical care and public awareness. A cardiovascular disease affects heart or blood vessels (arteries, veins and capillaries) or both by blocking the blood flow. As a surgical interventions, stent implants are deployed to cure or ameliorate the disease. However, the high failure rate of stents has lead researchers to give special attention towards analyzing stent structure, materials and characteristics. Many works related to …

In this study, the thermal properties of low dimensional materials such as graphene and boron nitride nanotube were investigated. As one of important heat transfer characteristics, interfacial thermal resistance (ITR) between graphene and Cu film was estimated by both experiment and simulation. In order to characterize ITR, the micropipette sensing technique was utilized to measure the temperature profile of suspended and supported graphene on Cu substrate that is subjected to continuous wave laser as a point source heating. By measuring the temperature of suspended graphene, the intrinsic thermal conductivity of suspended graphene was measured and it was used for estimating interfacial thermal resistance between graphene and Cu film. For simulation, a finite element method and a multiparameter fitting technique were employed to find the best fitting parameters. A temperature profile on a supported graphene on Cu was extracted by a finite element method using COMSOL Multiphysics. Then, a multiparameter fitting method using MATLAB software was used to find the best fitting parameters and ITR by comparing experimentally measured temperature profile with simulation one. In order to understand thermal transport between graphene and Cu substrate with different interface distances, the phonon density of states at the interface between graphene and Cu …

Programmable matter is a material whose properties can be programmed to achieve particular shapes or mechanical properties upon command. This is an essential technique that could one day lead to morphing aircraft and ground vehicles. Metamaterials are the rationally designed artificial materials whose properties are not observed in nature. Their properties are typically controlled by geometry rather than chemical compositions. Combining metamaterials with a programmable function will create a new area in the intelligent material design. The objective of this study is to design and demonstrate a tunable metamaterial and to investigate its thermo-mechanical behavior. An integrated approach to the metamaterial design was used with analytical modeling, numerical simulation, and experimental demonstration. The dynamic thermo-mechanical analysis was used to measure base materials' modulus and thermal expansion coefficient as a function of temperature. CPS, the unit cell of the metamaterial, is composed of circular holes and slits. By decomposing kinematic rotation of the arm and elastic deformation of a bi-material hinge, thermo-mechanical constitutive models of CPS were developed and it was extended to 3D polyhedral structures for securing isotropic properties. Finite element based numerical simulations of CPS and polyhedral models were conducted for comparison with the analytical model. 3D printing of …

This research demonstrates the use of friction stir welding (FSW) to join dissimilar (Al-Mg) metal alloys. The main challenges in joining different, dissimilar metal alloys is the formation of brittle intermetallic compounds (IMCs) in the stir zone affecting mechanical properties of joint significantly. In this present study, FSW joining process is used to join aluminum alloy AA2139 and magnesium alloy WE43. The 9.5 mm thick plates of AA2139 and WE43 were friction stir butt welded. Different processing parameters were used to optimize processing parameters. Also, various weldings showed a crack at interface due to formation of IMCs caused by liquation during FSW. A good strength sound weld was obtained using processing parameter of 1200 rev/min rotational speed; 76.2 mm/min traverse speed; 1.5 degree tilt and 0.13 mm offsets towards aluminum. The crack faded away as the tool was offset towards advancing side aluminum. Mostly, the research was focused on developing high strength joint through microstructural control to reduce IMCs thickness in Al-Mg dissimilar weld joint with optimized processing parameter and appropriate tool offset.

One of the major goal of the researchers is to reduce energy loss including nanoscale to the structural level. For instance, around 65% of fuel energy is lost during the propulsion of the automobiles, where 11% of the loss happens at tires due to rolling friction. Out of that tire loss, 90 to 95% loss happens due to hysteresis of tire materials. This dissertation focuses on multiscale modeling techniques in order to facilitate the discovery new rubber materials. Enhanced coarse-grained models of elastomers (thermoplastic polyurethane elastomer and natural rubber) are constructed from full-atomic models with reasonable repeat units/beads associated with pressure-correction for non-bonded interactions of the beads using inverse Boltzmann method (IBM). Equivalent continuum modeling is performed with volumetric/isochoric loading to predict macroscopic mechanical properties using molecular mechanics (MM) and molecular dynamics (MD). Glass-transition and rate-dependent mechanical properties along with hysteresis loss under uniaxial deformation is predicted with varying composition of the material. A statistical non-Gaussian treatment of a rubber chain is performed and linked with molecular dynamics in order predict hyperelastic material constants without fitting with any experimental data.

Due to the multi-tasking and miniaturization of electronic devices, faster heat transfer is required from the device to avoid the thermal failure. Die-attached polymer adhesives are used to bond the chips in electronic packaging. These adhesives have to hold strong mechanical, thermal, dielectric, and moisture resistant properties. As polymers are insulators, heat conductive particles are inserted in it to enhance the thermal flow with an attention that there would be no electrical conductivity as well as no reduction in dielectric strength. This thesis focuses on the characterization of polymer nanocomposites for thermal and electrical properties with experimental and computational tools. Platelet geometry of hexagonal boron nitride offers highly anisotropic properties. Therefore, their alignment and degree of orientation offers tunable properties in polymer nanocomposites for thermal, electrical, and mechanical properties. This thesis intends to model the anisotropic behavior of thermal and dielectric properties using finite element and molecular dynamics simulations as well as experimental validation.

This thesis is an experimental study of the fluidization of binary mixture in particulate flows. A fluidized bed with two distributors was built with water being used as carrying fluid. Three types of solid particles of nylon, glass and aluminum of the same size and different densities are used in the experiments. The wall effect on a single particle fluidization, the fluidization of binary mixture of large density difference (nylon and aluminum of density ratio of 0.42), and the fluidization of binary mixture of close density (glass and aluminum with density ratio of 0.91) were investigated. Also, the effect of distributors on mono-disperse and bi-disperse particle fluidization was investigated. Results show that the presence of narrow walls reduces the minimum fluidization velocity for a single particle by as much as nearly 40%. Also, in the case of binary mixture of close density particles, uniform mixing was easily achieved and no segregation was observed, but in the case of large density difference particles, there exists significant segregation and separation. At high velocity, the uniform distributor behaves like a transport bed. To achieve a full bed in the single jet, it requires 1.5 times velocity of the uniform distributor. This behavior determines …

Natural disasters are affecting a significant number of people around the world. Sheltering is the first step in post-disaster activities towards the normalization of the affected people's lives. Temporary housing is being used in these cases until the construction of permanent houses are done. Disposal of temporary housing after use is leading to a significant environmental impact because most of them are filled with thermally insulative polymer foams that do not degrade in a short period. To reduce these problems this work proposes to use foams made with compostable thermoplastic polylactic acid (PLA) and degradable kenaf core as filler materials; these foams are made using CO2 as blowing agent for insulation purposes. Foams with PLA and 5%, 10% and 15% kenaf core were tested. Different properties and their relations were examined using differential scanning calorimetry (DSC), thermal conductivity, mechanical properties, scanning electron microscopy (SEM), x-ray μ-computed tomography (μ-CT) and building energy simulations were done using Energy Plus by NREL. The results show that mechanical properties are reduced with the introduction of kenaf core reinforcement while thermal conductivity display a noticeable improvement.

Corrosion represents the single most frequent cause for product replacement or loss of product functionality with a 5% coat to the industrial revenue generation of any country in this dissertation the efficacy of using filled coatings as a protection coating are investigated. Fillers disrupt the polymer-substrate coating interfacial area and lead to poor adhesion. Conflicting benefits of increasing surface hardness and corrosion with long term durability through loss of adhesion to the substrate are investigated. The effects of filler type, filler concentration and exposure to harsh environments such as supercritical carbon dioxide on salt water corrosion are systematically investigated. The constants maintained in the design of experiments were the substrate, AISI-SAE 1018 steel substrate, and the corrosive fluid synthetic sea salt solution (4.2 wt%) and the polymer, Bismaleimide (BMI). Adhesion strength through pull-off, lap shear and shear peel tests were determined. Corrosion using Tafel plots and electrochemical impedance spectroscopy was conducted. Vickers hardness was used to determine mechanical strength of the coatings. SEM and optical microscopy were used to examine dispersion and coating integrity. A comparison of fillers such as alumina, silica, hexagonal boron nitride, and organophilic montmorillonite clay (OMMT) at different concentrations revealed OMMT to be most effective with …

Texas is the second largest state in U.S.A. based on geographical area, population and the economy. It is home to several large coastal urban areas with major industries and infrastructure supporting the fossil-fuel based energy sector. Most of the major cities on the state have been impacted by significant air pollution events over the past decade. Studies conducted in the southern coastal region of TX have identified long range transport as a major contributor of particulate matter (PM) pollution along with local emissions. Biomass burns, secondary sulfates and diesel emissions sources are comprise as the dominant mass of PM2.5 have been noted to be formed by the long range transport biomass from Central America. Thus, the primary objective of this study was to identify and quantify local as well as regional sources contributing to the PM pollution in the coastal area of Brownsville located along the Gulf of Mexico. Source apportionment techniques such as principal component analysis (PCA) and positive matrix factorization (PMF) were employed on the air quality monitoring data to identify and quantify local and regional sources affecting this coastal region. As a supplement to the PMF and PCA, conditional probability function (CPF) analysis and potential source contribution …

The thesis describes novel glass micropipette thermal sensor fabricated in cost-effective manner and thermal conductivity measurement of carbon nanotubes (CNT) thin film using the developed sensor. Various micrometer-sized sensors, which range from 2 µm to 30 µm, were produced and tested. The capability of the sensor in measuring thermal fluctuation at micro level with an estimated resolution of ±0.002oC is demonstrated. The sensitivity of sensors was recorded from 3.34 to 8.86 µV/oC, which is independent of tip size and dependent on the coating of Nickel. The detailed experimental setup for thermal conductivity measurement of CNT film is discussed and 73.418 W/moC was determined as the thermal conductivity of the CNT film at room temperature.

Campus dormitories for the University of North Texas house over 5500 students per year; each one of them requires certain comfortable living conditions while they live there. There is an inherit amount of money required in order to achieve minimal comfort levels; the cost is mostly natural gas for water and room heating and electricity for cooling, lighting and peripherals. The US Department of Energy has developed several programs to aid in performing energy simulations to help those interested design more cost effective building designs. Energy-10 is such a program that allows users to conduct whole house evaluations by reviewing and altering a few parameters such as building materials, solar heating, energy efficient windows etc. The idea of this project was to recreate a campus dormitory and try to emulate existent energy consumption then try to find ways of lowering that usage while maintaining a high level of personal comfort.

Laminar natural convection heat transfer from the vertical surface of a cylinder is a classical subject, which has been studied extensively. Furthermore, this subject has generated some recent interest in the literature. In the present investigation, numerical experiments were performed to determine average Nusselt numbers for isothermal vertical cylinders (103 < RaL < 109, 0.5 < L/D <10, and Pr = 0.7) with and without an adiabatic top in a quiescent ambient environment which will allow for plume growth. Results were compared with commonly used correlations and new average Nusselt number correlations are presented. Furthermore, the limit for which the heat transfer results for a vertical flat plate may be used as an approximation for the heat transfer from a vertical cylinder was investigated.

The objective of this research is to develop a wearable device that could harvest waste mechanical energy of the human hand movement and utilize this energy to suppress wrist tremors. Piezoelectric material is used to measure the hand movement signals, and the signal of wrist tremor is filtered to be utilized to suppress the tremor. In order to conduct the experiment of energy harvesting and tremor suppression, an experimental rig was fabricated. Two types of piezoelectric materials, PVDF (polyvinylidene fluoride) films and MFC (macro fiber composite) films, are used to harvest mechanical energy and used as actuators to suppress hand tremors. However, due to some shortages of the materials, these two types of materials are not used as actuators to suppress the wrist tremors. Thus, we use Matlab Simulink to simulate the tremor suppression with AVC (active vibration control) algorithm.

Texas, due to its geographical area, population, and economy is home to a variety of industrialized areas that have significant air quality problems. These urban areas are affected by elevated levels of fine particulate matter (PM2.5). The primary objective of this study was to identify and quantify local and regional sources of air pollution affecting the city of Houston, Texas. Positive Matrix Factorization (PMF) techniques were applied to observational datasets from two urban air quality monitoring sites in Houston from 2003 through 2008 in order to apportion sources of pollutants affecting the study region. Data from 68 species for Aldine and 91 for Deer Park were collected, evaluated, and revised to create concentration and uncertainty input files for the PMF2 and EPA PMF (PMF3) source apportionment models. A 11-sources solution for Aldine and 10-sources for Deer Park were identified as the optimal solutions with both models. The dominant contributors of fine particulate matter in these sites were found to be biomass burnings (2%-8.9%), secondary sulfates I (21.3%-7.6%) and II (38.8%-22.2%), crustal dust (8.9%-10.9%), industrial activities (10.9%-4.2%), traffic (23.1%-15.6%), secondary nitrates (4.4%-5.5%), fresh (1%-1.6%) and aged(5.1%-4.6%) sea salt and refineries (1.3%-0.6%), representing a strong case to confirm the high influence of …

In this study, gas sensing systems that are based on piezoelectric smart material and structures are proposed, designed, developed, and tested, which are mainly aimed to address the temperature dependent CO2 gas sensing in a real environment. The state-of-the-art of gas sensing technologies are firstly reviewed and discussed for their pros and cons. The adsorption mechanisms including physisorption and chemisorption are subsequently investigated to characterize and provide solutions to various gas sensors. Particularly, a QCM based gas sensor and a C-axis inclined zigzag ZnO FBAR gas sensor are designed and analyzed for their performance on room temperature CO2 gas sensing, which fall into the scope of physisorption. In contrast, a Langasite (LGS) surface acoustic wave (SAW) based acetone vapor sensor is designed, developed, and tested, which is based on the chemisorption analysis of the LGS substrate. Moreover, solid state gas sensors are characterized and analyzed for chemisorption-based sensitive sensing thin film development, which can be further applied to piezoelectric-based gas sensors (i.e. Ca doped ZnO LGS SAW gas sensors) for performance enhanced CO2 gas sensing. Additionally, an innovative MEMS micro cantilever beam is proposed based on the LGS nanofabrication, which can be potentially applied for gas sensing, when combined with …

Fiber-reinforced concrete (FRC) is nowadays extensively used in civil engineering throughout the world due to the composites of FRC can improve the toughness, flexural strength, tensile strength, and impact strength as well as the failure mode of the concrete. It is an easy crazed material compared to others materials in civil engineering. Concrete, like glass, is brittle, and hence has a low tensile strength and shear capacity. At present, there are different materials that have been employed to reinforce concrete. In our experiment, nanostructures iron oxide was prepared by electrodepostion in an electrolyte containing 0.2 mol/L sodium acetate (CH3COONa), 0.01 mol/L sodium sulfate (Na2SO4) and 0.01 mol/L ammonium ferrous sulfate (NH4)2Fe(SO4)2.6H2O under magnetic stirring. The resulted showed that pristine Fe2O3 particles, Fe2O3 nanorods and nanosheets were synthesized under current intensity of 1, 3, 5 mA, respectively. And the pull-out tests were performed by Autograph AGS-X Series. It is discovering that the load force potential of nanostructure fibers is almost 2 times as strong as the control sample.

A recent trend in the development of renewable and biodegradable materials has led to the development of composites from renewal sources such as natural fibers. This agricultural activity generates a large amount of waste in the form of peanut shells. The motivation for this research is based on the utilization of peanut shells as a viable source for the manufacture of biocomposites. High-density polyethylene (HDPE) is a plastic largely used in the industry due to its durability, high strength to density ratio, and thermal stability. This research focuses in the mechanical and thermal properties of HDPE/peanut shell composites of different qualities and compositions. The samples obtained were subjected to dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and mechanical tensile strength tests. TO prepare the samples for analysis, the peanut shells were separated into different mesh sizes and then mixed with HDPE at different concentrations. The results showed that samples with fiber size number 10 exhibited superior strength modulus of 1.65 GPa versus results for HDPE alone at 1.32 GPa. The analysis from the previous experiments helped to determine that the fiber size number 10 at 5%wt. ratio in HDPE provides the most optimal mechanical and thermal results. From tensile …