PM2.5 particle sensing has been done using surface acoustic wave based sensor for two different frequencies. Due to mass loading and elasticity loading on the sensor's surface, the center frequency of the sensor shifts. The particle concentration can be tracked based on that frequency shift. The fit factor test has been conducted using higher frequency SAW sensor. The consist results has been achieved for particle sensing and fit factor test with SAW based sensor.

This dissertation is devoted to the development of novel devices for optoelectronic and photovoltaic applications using the promise of inkjet printing with two-dimensional (2D) materials. A systematic approach toward the characterization of the liquid exfoliated 2D inks comprising of graphene, molybdenum disulfide (MoS2), tungsten diselenide (WSe2), and 2D perovskites is discussed at depth. In the first study, the biocompatibility of 2D materials -- graphene and MoS2 -- that were drop cast onto flexible PET and polyimide substrates using mouse embryonic fibroblast (STO) and human esophageal fibroblast (HEF) cell lines, was explored. The polyimide samples for both STO and HEF showed high biocompatibility with a cell survival rate of up to ~ 98% and a confluence rate of 70-98%. An inkjet printed, biocompatible, heterostructure photodetector was constructed using inks of photo-active MoS2 and electrically conducting graphene, which facilitated charge collection of the photocarriers. The importance of such devices stems from their potential utility in age-related-macular degeneration (AMD), which is a condition where the photosensitive retinal tissue degrades with aging, eventually compromising vision. The biocompatible inkjet printed 2D heterojunction devices were photoresponsive to broadband incoming radiation in the visible regime, and the photocurrent scaled proportionally with the incident light intensity, exhibiting a …

With the rapid development of wireless communication technology, the demands for higher communication rates are increasing. Higher communication rate corresponds to higher DoF. Interference alignment, which is an emerging interference management technique, is able to substantially increase the DoF of wireless communication systems. This thesis mainly studies the delay-based interference alignment technique. The key problem lies in the design of the transmission scheme and the appropriate allocation of the propagation delay, so as to achieve the desired DoF of different wireless networks. In addition, through delay-based interference alignment, the achievability of extreme points of the DoF region of different wireless networks can be proved.

A wearable body temperature sensor would allow for early detection of fever or infection, as well as frequent and accurate hassle-free recording. This thesis explores the design of a body-temperature-sensing device inkjet-printed on a flexible substrate. All structures were first modeled by first-principles, theoretical calculations, and then simulated in HFSS. A variety of planar square inductor geometries were studied before selecting an optimal design. The designs were fabricated using multiple techniques and compared to the simulation results. It was determined that inductance must be carefully measured and documented to ensure good functionality. The same is true for parallel-plate and interdigitated capacitors. While inductance remains relatively constant with temperature, the capacitance of the device with a temperature-sensitive dielectric layer will result in a shift in the resonant frequency as environmental or ambient temperature changes. This resonant frequency can be wirelessly detected, with no battery required for the sensing device, from which the temperature can be deduced. From this work, the optimized version of the design comprises of conductive silver in with a temperature-sensitive graphene oxide layer, intended for inkjet-printing on flexible polyimide substrates. Graphene oxide demonstrates a high dielectric permittivity with good sensing capabilities and high accuracy. This work pushes the …

In this work, we study the properties and device applications of MoS2, black phosphorus, MoOx, and NbSe2. We first start with the design, fabrication, and characterization of ultra-high responsivity photodetectors based on mesoscopic multilayer MoS2. The device architecture is comprised of a metal-semiconductor-metal (MSM) photodetector, where Mo was used as the contact metal to suspended MoS2 membranes. The dominant photocurrent mechanism was determined to be the photoconductive effect, while a contribution from the photogating effect was also noted from trap-states that yielded a wide spectral photoresponse from UV-to-IR with an external quantum efficiency (EQE) ~ 104. From time-resolved photocurrent measurements, a fast decay time and response time were obtained with a stream of incoming ON/OFF white light pulses. Another interesting semiconductor 2D material that has attracted special attention due to its small bandgap and ultra-high hole mobility is the black phosphorus. An analysis of the optoelectronic properties and photocurrent generation mechanisms in two-dimensional (2D) multilayer crystallites of black phosphorus (BP) was conducted from 350 K down to cryogenic temperatures using a broad-band white light source. The Mo-BP interface yielded a low Schottky barrier "φ" _"SB" ~ -28.3 meV and a high photoresponsivity R of ~ 2.43 x 105 A/W at …

Although wireless sensor networks have been successfully used for environmental monitoring, one of the major challenges that this technology has been facing is supplying continuous and reliable electrical power during long-term field deployment. Batteries require repetitive visits to the deployment site to replace them once discharged; admittedly, they can be recharged from solar panels, but this only works in open areas where solar radiation is unrestricted. This dissertation introduces a novel approach to design and implement a reliable efficient solar energy harvester to continuously, and autonomously, provide power to wireless sensor nodes for long-term applications. The system uses supercapacitors charged by a solar panel and is designed to reduce power consumption to very low levels. Field tests were conducted for more than a year of continuous operation and under a variety of conditions, including areas under dense foliage. The resulting long-term field data demonstrates the feasibility and sustainability of the harvester system for challenging applications. In addition, we analyzed solar radiation data and supercapacitor charging behavior and showed that the harvester system can operate battery free, running on the power provided by supercapacitors. A battery is included only for backup in case the supercapacitor storage fails. The proposed approach provides …

Coarse-Grained Reconfigurable Architectures (CGRAs) are promising in developing high performance low-power portable applications. In this research, we crowdsource a mapping problem using gamification to harnass human intelligence. A scientific puzzle game, Untangled, was developed to solve a mapping problem by encapsulating architectural characteristics. The primary motive of this research is to draw insights from the mapping solutions of players who possess innate abilities like decision-making, creative problem-solving, recognizing patterns, and learning from experience. In this dissertation, an extensive analysis was conducted to investigate how players' computational skills help to solve an open-ended problem with different constraints. From this analysis, we discovered a few common strategies among players, and subsequently, a library of dictionaries containing identified patterns from players' solutions was developed. The findings help to propose a better version of the game that incorporates these techniques recognized from the experience of players. In the future, an updated version of the game that can be developed may help low-performance players to provide better solutions for a mapping problem. Eventually, these solutions may help to develop efficient mapping algorithms, In addition, this research can be an exemplar for future researchers who want to crowdsource such electrical engineering problems and this approach can …

This thesis offers the design and improvement of a 2 GHz to 20 GHz low noise amplifier (LNA) utilizing pHEMT technology. The pHEMT technology allows the LNA to generate a boosted signal at a lower noise figure (NF) while consuming less power and achieving smooth overall gain. The design achieves an overall gain (S21) of ≥ 10 dB with an NF ≤ 2 dB while consuming ≤ 30 mA of power while using commercial off-the-shelf (COTS) components.

As technology has advanced, data has become more and more important. The more breakthroughs are achieved, the more data is needed to support them. As a result, more storage is required in the system's memory. Compression is therefore required. Before it can be stored, the data must be compressed. To ensure that information is not lost, efficient compression is necessary. This also makes sure that there is no redundancy in the data that is being kept and stored. Compressive sensing has emerged as a new field of compression thanks to developments in sparse optimization. Rather than relying just on compression and sensing formulations, the theory blends the two. The objective of this thesis is to analyze the concept of compressive sensing and to study several reconstruction algorithms. Additionally, a few of the algorithms were put into practice. This thesis also included a model of the ECG, which is vital in determining the health of the heart. For the most part, the ECG is utilized to diagnose heart illness, and a modified synthetic ECG can be used to mimic some of these arrhythmias.

Emotions have significant importance in human life in learning, decision-making, daily interaction, and perception of the surrounding environment. Hence, it has become very essential to detect and recognize a person's emotional states and to build a connection between humans and computers. This process is called brain-computer interaction (BCI) and is a vast field of research in neuroscience. Hence, in the past few years, emotion recognition has gained adequate attention in the research community. In this thesis, an emotion recognition system is designed and analyzed using EEG signals. Several existing feature extraction techniques are studied, analyzed, and implemented to extract features from the EEG signals. An SVM classifier is used to classify the features into various emotional states. Four emotional states are detected, namely, happy, sad, anger, and relaxed state. The model is tested, and simulation results are presented with an interpretation. Furthermore, this study has mentioned and discussed the efficacy of the results achieved. The findings from this study could be beneficial in developing emotion-sensitive technologies, such as augmented modes of communication for severely disabled individuals who are unable to communicate their feelings directly.

It is known that quantum strategies change the range of possible payoffs for the players in the prisoner's dilemma. In this paper, we examine the effect of the degree of entanglement in determining the payoffs. When both players play quantum strategies, we show that the payoff for both players is unaffected by the entanglement value and it leads to a new Nash equilibrium.

Wireless power transfer (WPT) is currently the most efficient way for transmission of power from one port to another, that is popularly used in various applications.This technique can change the previous energy utilization methods in various applications such as electronic devices, implanted medical devices, electrical vehicles and so forth.It mainly helps overcome the limitations of short battery life, limited storage, heavy weight, and high cost of batteries.This paper is based on the design of a transmitter and a receiver to achieve wireless power transfer for applications like optogenetic stimulation in rodents. With inductive coupling, a very high efficiency can be achieved between the transmitting and receiving coils of an antenna at small distances. When the transmitter and receiver are strongly coupled and are working at their resonant frequencies, the range of efficient WPT can be extended. In this work, the simulations are performed in HFSS at a resonating frequency of 13.56 MHz.A 4-port transmitter and a single-port planar receiver model are developed in HFSS, and the simulations are performed to graph the S parameters with a separation distance of 4cm. A Wilkinson power divider is designed using ADS to split the power from the four ports of the transmitter. The …

The key requirements of a reliable neural signal recording system include low power to support long-term monitoring, low noise, minimum tissue damage, and wireless transmission. The neural spikes are also detected and sorted on-chip/off-chip to implement closed-loop neuromodulation in a high channel count setup. All these features together constitute an empirical neural recording system for neuroscience research. In this prospectus, we propose to develop a neural signal acquisition system with wireless transmission and feature extraction. We start by designing a prototype entirely built with commercial-off-the-shelf components, which includes recording and wireless transmission of synthetic neural data and feature extraction. We then conduct the CMOS implementation of the low-power multi-channel neural signal recording read-out circuit, which enables the in-vivo recording with a small form factor. Another direction of this thesis is to design a self-powered motion tracking read-out circuit for wearable sensors. As the wearable industry continues to advance, the need for self-powered medical devices is growing significantly. In this line of research, we propose a self-powered motion sensor based on reverse electrowetting-on-dielectric (REWOD) with low-power integrated electronics for remotely monitoring health conditions. We design the low-power read-out circuit for a wide range of input charges, which is generated from the …

In recent years, deep learning based computer vision technology has developed rapidly. This is not only due to the improvement of computing power, but also due to the emergence of high-quality datasets. The combination of object detectors and drones has great potential in the field of rescue and disaster relief. We created an image dataset specifically for vision applications on drone platforms. The dataset contains 5000 images, and each image is carefully labeled according to the PASCAL VOC standard. This specific dataset will be very important for developing deep learning algorithms for drone applications. In object detection models, loss function plays a vital role. Considering the uneven distribution of large and small objects in the dataset, we propose adjustment coefficients based on the frequencies of objects of different sizes to adjust the loss function, and finally improve the accuracy of the model.

Electrocardiogram (ECG) is a biological signal that represents the heart's electrical activity. Interference from power lines introduces a frequency component of 50 to 60 Hz into the signal, which is the principal cause of ECG corruption. By using the Cadence Virtuoso Spectre circuit simulator and typical TSMC RF 180 nm CMOS technology, a notch filter was created to reduce powerline interference. The advantage of utilizing a notch filter for PLI is that noise at 60 Hz is completely eliminated without sacrificing any important information. Additionally, this study contains a MATLAB-based model for, which is used to compute the power spectral density for the obtained time-domain signal. By incorporating power spectral density into data gathering procedures, it is feasible to enhance data collection methodologies, construct models that appropriately account for observed power and aid in the removal of undesired components. NI LabVIEW is used to extract features. The advantage of ECG feature extraction is that it provides information that assists in the identification of cardiac rhythm issues, and gives information about the occurrence of heart attack. In this study, several patient data sets are utilized to extract characteristics and provide information regarding heart condition abnormalities.

The main objective of this thesis is to propose a localization method for a UAV using various computer vision and machine learning techniques. It plays a major role in planning the strategy for the flight, and acts as a navigational contingency method, in event of a GPS failure. The implementation of the algorithms employs high processing capabilities of the graphics processing unit, making it more efficient. The method involves the working of various neural networks, working in synergy to perform the localization. This thesis is a part of a collaborative project between The University of North Texas, Denton, USA, and the University of Windsor, Ontario, Canada. The localization has been divided into three phases namely object detection, recognition, and location estimation. Object detection and position estimation were discussed in this thesis while giving a brief understanding of the recognition. Further, future strategies to aid the UAV to complete the mission, in case of an eventuality, like the introduction of an EDGE server and wireless charging methods, was also given a brief introduction.

Currently, there is no equipment to measure the real-time fit of EHMR or N-95masks which are used in harsh environments. Improper fit of these EHMRs or N-95 masks exposes the personnel to hazardous environments. Surface acoustic wave (SAW) sensors have been around for few decades and are being used in various applications. In this work, real-time PM2.5 detection using passive wireless SAW sensors is presented. The design of meander antenna at 433MHz for wireless interrogation of SAW sensor using HFSS and ADS is also presented in this thesis. This works also includes the design of YZ-lithium niobate SAW sensor including COMSOL simulation.

This thesis consists of two projects in the field of machine learning. Previous research in the OSCAR UNT lab based on KMeans color quantization is further developed and applied to individual color channels and segmented input images to explore compression rates while still maintaining high output image quality. The second project implements a small-scale dual path network for image classifiaction utilizing the CIFAR-10 dataset containing 60,000 32x32 pixel images ranging across ten categories.

This dissertation is particularly focused on a novel approach of a wirelessly powered neuromodulation system for chronic patients. The inductively coupled transmitter (TX) and receiver (RX) coils are designed through optimization to achieve maximum efficiency. A power management unit (PMU) consisting of a voltage rectifier, voltage regulator along with a stimulation circuitry is also designed to provide pulse stimulation to genetically modified neurons. For continuous health monitoring purposes, the response from the brain due to stimulation needs to be recorded and transmitted wirelessly outside the brain for analysis. A low-power high-data duty-cycled impulse-radio ultra-wideband (IR-UWB) transmitter is designed and implemented using the standard CMOS process. Another focus of this dissertation is the design of a reverse electrowetting-on-dielectric (REWOD) based energy harvesting circuit for wearable sensor applications which is capable of generating a very low-frequency signal from motion activity such a walking, running, jogging, etc. A commercial off-the-shelf (COTS) based and on-chip based energy harvesting circuit is designed for very low-frequency signals. The experimental results show promising progress towards the advancement in the wirelessly powered neuromodulation system and building the self-powered wearable sensor.

The feedback control system is defined as the sampling of an output signal and feeding it back to the input, resulting in an error signal that drives the overall system. This dissertation focuses on the stabilization and performance of state feedback control systems. Chapters 3 and 4 focus on the feedback control protocol approaching in the multi-agents system. In particular, the global regulation of distributed optimization problems has been considered. Firstly, we propose a distributed optimization algorithm based on the proportional-integral control strategy and the exponential convergence rate has been delivered. Moreover, a decentralized mechanism has been equipped to the proposed optimization algorithm, which enables an arbitrarily chosen agent in the system can compute the value of the optimal solution by only using the successive local states. After this, we consider the cost function follows the restricted secant inequality. A dynamic event-triggered mechanism design has been proposed. By ensuring the global regulation of the distributed proportional-integral optimization algorithm, the dynamic event-triggered mechanism efficiently reduces the communication frequency among agents. Chapter 5 focuses on the feedback control protocol approaching the single-agent system. Specifically, we investigate the truncated predictor feedback control of the regulation of linear input-delayed systems. For the purpose of …

Networked multi-agent systems have attracted lots of researchers to develop algorithms, techniques, and applications.A multi-agent networked system consists of more than one subsystem (agent) to cooperately solve a global problem with only local computations and communications in a fully distributed manner. These networked systems have been investigated in various different areas including signal processing, control system, and machine learning. We can see massive applications using networked systems in reality, for example, persistent surveillance, healthcare, factory manufacturing, data mining, machine learning, power system, transportation system, and many other areas. Considering the nature of those mentioned applications, traditional centralized control and optimization algorithms which require both higher communication and computational capacities are not suitable. Additionally, compared to distributed control and optimization approaches, centralized control, and optimization algorithms cannot be scaled into systems with a large number of agents, or guarantee performance and security. All of the limitations of centralized control and optimization algorithms motivate us to investigate and develop new distributed control and optimization algorithms in networked systems. Moreover, convergence rate and analysis are crucial in control and optimization literature, which motivates us to investigate how to analyze and accerlate the convergence of distributed optimization algorithms.