A 1H, 13C, and 6Li NMR study of 2-ethyl-1-butyllithium indicated that 2-ethyl-1-butyllithium exists only as a hexameric aggregate over the entire temperature range of 25 to - 92.1 ° C in cyclopentane. Reacting 2-ethyl-1-butyllithium with 2-ethyl-1-butanol resulted in alkyllithium/lithium alkoxide mixed aggregates, apparently of the form Ra(RO)bLia+b. A multinuclear, variable temperature NMR study of samples with O:Li ratios of 0.2 and 0.4 showed, in addition to the alkyllithium, the formation of four mixed aggregates, one of them probably an octamer. Higher O:Li ratio samples showed the formation of several other mixed aggregates. Mixing 2-ethyl-1-butyllithium with independently prepared lithium 2-ethyl-1-butoxide formed the same mixed aggregates formed by in situ synthesis of lithium alkoxide. Lithium 2-ethyl-1-butoxide also exists as aggregates in cyclopentane.

Dimethoxynaphthalene (donor) and quinone (acceptor) have been chosen as a suitable redox pair and are bonded to either permethylated silane chains or corresponding permethylated alkyl chains to form Acceptor-(Bridge)-Donor molecules. The idea that the s-delocalization phenomenon of silane chains may greatly facilitate ET reactions will be tested. The starting material for the donor precursor, 4-(1,4-dimethoxynaphthyl)bromocyclohexane, was 1,4-naphthoquinone. After methylation and bromination, the Grignard reagent of the resulting bromide was reacted with cyclohexanedione, mono ethylene ketal. The resulting alcohol was changed to the donor precursor through the following functional group transformation steps: dehydration, hydrogenation, deketalization and bromination. 1,4-Dibenzyloxybromobenzene, the precursor for the acceptor, was synthesized from 1,4-hydroquinone through bromination and benzylation. The connection of the two precursors and either permethylated silane chains or permethylated alkyl chains will give the final target molecules for ET research. Progress on this is included.

Understanding the thermodynamic properties of multicomponent mixtures is of critical importance in many chemical and industrial applications. Experimental measurements become progressively difficult as the number of solution components increases -- producing the need for predictive models. Problems in development of predictive models arise if the mixture has one or more components that interact through molecular complexation or association. Experimental solubilities of anthracene and pyrene dissolved in binary systems containing one or more alcohols were measured in order to address this problem. Alcohols examined in this study were: 1-propanol, 2-propanol, 1-butanol, 2-butanol, 2-methyl-1-propanol, 3-methyl-1-butanol, and 1-octanol. In binary solvent mixtures containing only a single self-associating alcoholic solvent, the alkane cosolvents studied were: n-hexane, n-heptane, n-octane, 2,2,4-trimethylpentane, cyclohexane, methylcyclohexane, tert-butylcyclohexane. Predictive solubility equations were developed using mobile order theory. This approach differs from classical solution models by representing hydrogen bonding with a probability term rather than with expressions derived from stepwise equilibria or expressions to represent hypothetical solution aggregates. Results were compared with the predicted solubilities found from using expressions developed using the Kretschmer-Wiebe and Mecke-Kempter approaches for modeling associated solutions. It was found that the mobile order approach provided reasonably accurate predictions for the solute solubilities in the systems studied. The …

Several studies were done to illustrate the versatillity of the Abraham model in mathematically describing the various solute-solvent interactions found in a wide range of different chemical and biological systems. The first study focused on using the solvation model to construct mathematical correlations describing the minimum inhibitory concentration of organic compounds for growth inhibition towards the three bacterial strains Porphyromonas gingivalis, Selenomonas artemidis, and Streptococcus sobrinus. The next several studies expand the practicallity of the Abraham model by predicting free energies of partition in chemical systems. The free energy studies expand the use of the Abraham model to other temperatures and properties by developing correlations for the enthalpies of solvation of gaseous solutes of various compounds dissolved in water, 1-octanol, hexane, heptane, hexadecane, cyclohexane, benzene, toluene, carbon tetrachloride, chloroform, methanol, ethanol, 1-butanol, propylene carbonate, dimethyl sulfoxide, 1,2-dichloroethane, N,N-dimethylformamide, tert-butanol, dibutyl ether, ethyl acetate, acetonitrile, and acetone. Also, a generic equation for linear alkanes is created for use when individual datasets are small. The prediction of enthalpies of solvation is furthered by modifying the Abraham model so that experimental data measured at different temperatures can be included into a single correlation expression. The temperature dependence is directly included in the model …

Polymer hydrogel films change their properties in response to environmental change. This remarkable phenomenon results in many potential applications of polymer hydrogel films. In this thesis colored thermo-sensitive poly(N-isopropylacrylamide) (PNIPAAm) hydrogel film was prepared by firstly synthesizing polymer latex and secondarily crosslinking the nanoparticles and casting the polymers onto glass. The shape-memory effect has been observed when changing the environmental temperature. The temperature-dependent of turbidity of polymer hydrogel film was measured by HP UVVisible spectrophotometer. This intelligent hydrogel might be used in chemomechanical systems and separation devices as well as sensors. Polymer adsorption plays an important role in many products and processes. In this thesis, surfactant-free three-dimensional polystyrene (PS) nanoparticle network has been prepared. The infrared spectroscopy and solubility experiment are performed to prove the crosslinking mechanism, also the BET method was used to measure the adsorption and desorption of polystyrene network. The BET constant (C) is calculated (C=6.32). The chemically bonded polymer nanoparticle network might have potential applications as catalyst or used for chromatographic columns.

Metal and oxide interactions are of broad scientific and technological interest in areas such as heterogeneous catalysis, microelectronics, composite materials, and corrosion. In the real world, such interactions are often complicated by the presence of interfacial impurities and/or high electric fields that may change the thermodynamic and kinetic behaviors of the metal/oxide interfaces. This research includes: (1) the surface hydroxylation effects on the aluminum oxide interactions with copper adlayers, and (2) effects of high electric fields on the interface of thin aluminum oxide films and Ni3Al substrate. X-ray photoelectron spectroscopy (XPS) studies and first principles calculations have been carried out to compare copper adsorption on heavily hydroxylated a- Al2O3(0001) with dehydroxylated surfaces produced by Argon ion sputtering followed by annealing in oxygen. For a heavily hydroxylated surface with OH coverage of 0.47 monolayer (ML), sputter deposition of copper at 300 K results in a maximum Cu(I) coverage of ~0.35 ML, in agreement with theoretical predictions. Maximum Cu(I) coverage at 300 K decreases with decreasing surface hydroxylation. Exposure of a partially dehydroxylated a-Al2O3(0001) surface to either air or 2 Torr water vapor results in recovery of surface hydroxylation, which in turn increases the maximum Cu(I) coverage. The ability of surface hydroxyl …

The reaction between the tetrahedrane cluster RCCo3(CO)9{R = CHO (1), H (3)} and the redox-active diphosphine ligand 4,5-bis(diphenylphosphino)-4-cyclopenten-1,3- dione (bpcd) leads to the replacement of two CO groups and formation of RCCo3(CO)7(bpcd) {R = CHO (2), H (4)}. Clusters 2 and 4 are thermally unstable and readily transform into the new P-C bond cleavage cluster 5. All three clusters 2, 4, and 5 have been isolated and fully characterized in solution by IR and 31P NMR spectroscopy. VT 31P NMR data indicate that the bpcd ligand in RCCo3(CO)7(bpcd) is fluxional at 187 K in THF. Clusters 2, 4, and 5 have been structurally characterized by X-ray diffraction analyses.

The theoretical model of Beratan and Onuchic predicts a large attenuation of ET rates through hydrogen bonds; however, the effect of individual hydrogen bond on electron transfer reaction has not been systematically studied. The organic complexes in this study are a series of crown ether/ammonium salt, which incorporate a redox partner on each component of the complex. The dimethoxynaphthalene redox donor was attached to the crown ether and a series of ammonium salts was synthesized which bear substituted quinone and naphthoquinone acceptor. The complexes characterization and preliminary electron transfer rate measurement were completed with UV/Vis and steady-state emission spectroscopy.

A variable temperature 1H, 13C, and 6Li NMR study of n-propyl-6Li-lithium showed five different aggregates, similar to that in the literature as (RLi)n, n= 6, 8, 9, 9, 9. There were also a number of additional new species, identified as lithium hydride containing aggregates. Unexpectedly, a series of 13C{1H} 1-D NMR experiments with selective 6Li decoupling showed evidence for 13C-6Li spin-spin coupling between the previously reported (RLi)n aggregates and various hydride species.

Gas phase kinetics of the reactions involving hydroxyl radical and hydrogen atom were studied using experimental and ab initio theoretical techniques. The rate constant for the H + H2S reaction has been measured from 298 to 598 K by the laser photolysis/resonance fluorescence (LP-RF) technique. The transition state theory (TST) analysis coupled with the measurements support the suggestion that the reaction shows significant curvature in the Arrhenius plot. The LP-RF technique was also used to measure the rate constant of the H + CH3Br reaction over the temperature range 400-813 K. TST and density functional theory (DFT) calculations show that the dominant reaction channel is Br-abstraction. The reaction H + CF2=CF-CF=CF2 was first studied by flash photolysis/resonance fluorescence (FP-RF) method. The experiments of this work revealed distinctly non-Arrhenius behavior, which was interpreted in terms of a change in mechanism. DFT calculations suggest that the adduct is CF2H-CF•-CF=CF2. At lower temperatures a mixture of this molecule and CF2•-CFH-CF=CF2 is likely. The theoretical calculations show that H atom migrates in the fluoroethyl radicals through a bridging intermediate, and the barrier height for this process is lower in the less fluorinated ethyl radical. High level computations were also employed in studies of the …

Fluorocarbons are known to be stiffer than their hydrocarbon analogues, a property that underlines the extensive industrial application of fluorocarbon materials. Although there has been previous studies on the rotational barrier of molecules having fluorocarbon centers, a detailed systematic study is necessary to quantify flurocarbon stiffness. The molecules, Pyrene-(CF2)n-Pyrene, Pyrene-(CF2)n-F, Pyrene-(CH2)n-Pyrene and Pyrene-(CH2)n-H were therefore synthesized to enable the determination of the barrier to rotation of the carbon backbone in fluorocarbons. Conformational studies will be completed with steady-state and time-dependent emission spectroscopy.

The silicon based sensor is able to detect part per trillion ionic silver in 0.0098% hydrofluoric acid based on the open circuit potential (OCP) measurement. The OCP jump of 100 ppt ionic silver solution is up to 120 mV. The complex agent can effectively suppress the ionic silver concentration and suppress the OCP signal. The ability of complex agent to suppress the OCP signal depends on the formation constant of the complex with silver. The complex adsorbed on the sensor surface induces a second OCP jump, the height of the second jump depends on the formation constant of the complex. The MINEQL chemical equilibrium modeling program is used to calculate the ionic silver concentration when complex agent presents, a discrepancy is found between the MINEQL simulation result and the OCP signal of the silicon based sensor. The toxicity of ionic silver to C. dubia is studied parallel to the OCP signal of silicon based sensor. Less toxicity is found when the complex agent is present similar to the OCP signal. Another discrepancy is found between the MINEQL simulation and the toxicity test when MINEQL simulation is used to predict and control the ionic silver concentration. The data from both biosensor …

The focus of this research is to study the interaction between copper and the diffusion barrier/adhesion promoter. The behavior of copper sputter-deposited onto sputter-cleaned tantalum nitride is investigated. The data show that copper growth on tantalum nitride proceeds with the formation of 3-D islands, indicating poor adhesion characteristics between copper and Ta0.4N. Post-annealing experiments indicate that copper will diffuse into Ta0.4N at 800 K. Although the data suggests that Ta0.4N is effective in preventing copper diffusion, copper's inability to wet Ta0.4N will render this barrier ineffective. The interaction of copper with oxidized tantalum silicon nitride (O/TaSiN) is characterized. The data indicate that initial copper depositions result in the formation a conformal ionic layer followed by Cu(0) formation in subsequent depositions. Post-deposition annealing experiments performed indicate that although diffusion does not occur for temperatures less than 800 K, copper "de-wetting" occurs for temperatures above 500 K. These results indicate that in conditions where the substrate has been oxidized facile de-wetting of copper may occur. The behavior of a sputter-deposited Cu0.6Al0.4 film with SiO2 (Cu0.6Al0.4/SiO2) is investigated. The data indicate that aluminum segregates to the SiO2 interface and becomes oxidized. For copper coverages less than ~ 0.31 ML (based on a Cu/O …

Aluminum was deposited onto both Teflon AF and Parylene AF surfaces by chemical vapor deposition of trimethylaluminum. This work shows that similar thin film (100 Angstroms) aluminum oxide adlayers form on both polymers at the low temperature dosing conditions used in the studies. Upon anneal to room temperature and above, defluorination of the polymer surfaces increased and resulted in fluorinated aluminum oxide adlayers; the adlayers were thermally stable to the highest temperatures tested (600 K). Angle-resolved spectra showed higher levels of fluorination toward the polymer/adlayer interface region. Copper films were also deposited at low temperature onto Teflon AF using a copper hexafluoroacetylacetonate-cyclooctadiene precursor. Annealing up to 600 K resulted in the loss of precursor ligands and a shift to metallic copper. As with aluminum adlayers, some polymer defluorination and resulting metal (copper) fluoride was detected. Parylene AF and polystyrene films surfaces were modified by directly dosing with water vapor passed across a hot tungsten filament. Oxygen incorporation into polystyrene occurred exclusively at aromatic carbon sites, whereas oxygen incorporation into parylene occurred in both aromatic and aliphatic sites. Oxygen x-ray photoelectron spectra of the modified polymers were comparable, indicating that similar reactions occurred. The surface oxygenation of parylene allowed enhanced reactivity …

The novel instrumentation of nanomanipulation coupled to nanospray mass spectrometry and its applications are presented. The nanomanipulator has the resolution of 10nm step sizes allowing for specific fine movement used to probe and characterize objects of interest. Nanospray mass spectrometry only needs a minimum sample volume of 300nl and a minimum sample size of 300attograms to analyze an analyte making it the ideal instrument to couple to nanomanipulation. The nanomanipulator is mounted to an inverted microscope and consists of 4 nano-positioners; these nano-positioners hold end-effectors and other tools used for manipulation. This original coupling has been used to enhance the current abilities of cellular probing and trace fiber analysis. Experiments have been performed to demonstrate the functionality of this instrument and its capabilities. Histidine and caffeine have been sampled directly from single fibers and analyzed. Lipid bodies from cotton seeds have been sampled indirectly and analyzed. The few applications demonstrated are only the beginning of nanomanipulation coupled to nanospray mass spectrometry and the possible applications are numerous especially with the ability to design and fabricate new end-effectors with unique abilities. Future study will be done to further the applications in direct cellular probing including toxicology studies and organelle analysis of …

Web-based homework systems are becoming more common in general chemistry as instructors face ever-increasing enrollment. Yet providing meaningful feedback on assignments remains of the utmost importance. Chemistry instructors consider completion of homework integral to students' success in chemistry, yet only a few studies have compared the use of Web-based systems to the traditional paper-and-pencil homework within general chemistry. This study compares the traditional homework system to four different Web-based systems. Data from eight, semester classes consisting of a diagnostic pre-test, final semester grades, and the number of successful and unsuccessful students are analyzed. Statistically significant results suggest a chemistry instructor should carefully consider options when selecting a homework system.

A Series of fluorophores of the general formular P(CF2)nP and P(CF2)n-1CF3 has been synthesized. Copper catalyzed coupling of 1-bromopyrene and the corresponding mono and di-iodoperfluoroalkanes were used in most cases. For the n=3 dimer, a novel 1,w-perfluoroalkylation of pyrene via bis-decarboxylation of hexafluorogultaric acid was utilized. These compounds, along with suitable hydrocarbon analogs, are being used to study the flexibility of fluorocarbon chains using emission. We have found that the excimer formation for the fluorinated pyrene monomers is highly dependent on concentration and is less efficient than for pyene. Excimer formation for the fluorinated pyrene dimers is much more efficient than for the fluorocarbon monomers and is only slightly concentraion dependent. Steady-state emission spectra indicate hydrocarbon dimers-models form excimers more efficiently than the fluorinated dimers suggesting the fluorinated chains are stiffer than the hydrocarbons. We conducted the temperature-dependent studies and quantified the conformational difference.

The B3LYP density functional has been used to calculate properties of organometallic complexes of Co(CO)3 and ReBr(CO)3, with the chelating ligand 2,3-bisphosphinomaleic anhydride, in 19- and 18-electron forms. The SBKJC-21G effective core potential and associated basis set was used for metals (Co/Re) and the 6-31G* basis set was used for all other elements. The differences of bond angles, bond distances, natural atomic charges and IR vibrational frequencies were compared with the available experimental parameters. The differences between the 19- and 18-electron systems have been analyzed. The results reveal that the 19th electron is mostly distributed over the ligand of 2,3-bisphosphinomaleic anhydride, although partially localized onto the metal fragment in 1 and 2*. Two different methods, IR-frequencies and natural atomic charges, were used to determine the value of δ. Present computed values of δ are compared with available experimental values, and predictions are made for unknown complexes.

A 1H, 13C, and 6Li NMR study of 2-ethylhexyllithium showed that 2- ethylhexyllithium exists solely as a hexamer in cyclopentane solution over the temperature range from 25 to -65 °C. Furthermore, 2-ethylhexyllithium and lithium 2- ethyl-1-hexoxide were shown to form mixed aggregates when the alkoxide was formed in situ by reacting 2-ethylhexyllithium with 2-ethyl-1-hexanol. A multinuclear, variable temperature NMR study of a sample with an O:Li ratio of 0.2 led to the identification of at least four such aggregates, one of which was found to be a hexamer with the composition R5(RO)Li6. Studies of samples with higher O:Li ratios, up to 0.8, showed additional mixed aggregates present. All solutions containing mixed aggregates were also shown to contain hydrocarbon soluble lithium hydride. A study of lithium 2-ethyl-1- hexoxide indicated that it aggregates in solution as well.

Computational techniques were employed to investigate pathways that would improve the properties and characteristics of transition metal (i.e., ruthenium) catalysts, and to explore their mechanisms. The studied catalytic pathways are particularly relevant to catalytic hydroarylation of olefins. These processes involved the +2 to +3 oxidation of ruthenium and its effect on ruthenium-carbon bond strengths, carbon-hydrogen bond activation by 1,2-addition/reductive elimination pathways appropriate to catalytic hydrogen/deuterium exchange, and the possible intermediacy of highly coordinatively unsaturated (e.g., 14-electron) ruthenium complexes in catalysis. The calculations indicate a significant decrease in the Ru-CH3 homolytic bond dissociation enthalpy for the oxidation of TpRu(CO)(NCMe)(Me) to its RuIII cation through both reactant destabilization and product stabilization. This oxidation can thus lead to the olefin polymerization observed by Gunnoe and coworkers, since weak RuIII-C bonds would afford quick access to alkyl radical species. Calculations support the experimental proposal of a mechanism for catalytic hydrogen/deuterium exchange by a RuII-OH catalyst. Furthermore, calculational investigations reveal a probable pathway for the activation of C-H bonds that involves phosphine loss, 1,2-addition to the Ru-OH bond and then reversal of these steps with deuterium to incorporate it into the substrate. The presented results offer the indication for the net addition of aromatic C-H …

Baeyer-Villiger oxidation of 1-methylpentacyclo[5.4.0.02,6.03,10.05,9] undecane-8,11-dione, performed by using m-chloroperbenzoic acid in 1:1 molar ratio, resulted in the formation of monolactone. The corresponding dilactone, was synthesized by reacting 1-methyl-PCU-8,11-dione with m-chloroperbenzoic acid in 1:2 molar ratio. 6-Methyl-1,4,4a,8a-tetrahydro-1,4-methanonaphthalene-5,8-dione was converted into the corresponding exo-6,7-monoepoxide via treatment with 30% aqueous hydrogen peroxide. Epoxidation of this monoepoxide by using m-chloroperbenzoic acid afforded the corresponding bis-epoxide. Ceric ammonium nitrate (CAN) promoted oxidation of 1-methyl-PCU-8,11-dione afforded "methylated lactones" and a "methylated alkene."

The kinetics of the pressure dependent O + SO2 + Ar reaction have been investigated using laser photolysis resonance fluorescence at temperatures of 289 K, 399 K, 581 K, 699 K, 842 K and 1040 K and at pressures from 30-665 torr. Falloff was observed for the first time in the pressure dependence. Application of Lindemann theory yielded an Arrhenius expression of k(T) = 3.3 x 10-32exp(-992/T) cm6 molecule-1 s-1 for the low pressure limit and k(T) = 8.47 x 10-14exp(-468/T) cm3 molecule-1 s-1 for the high pressure limit at temperatures between 289 and 842 K. The reaction is unusual as it possesses a positive activation energy at low temperature, yet at higher temperatures the activation energy is negative, illustrating a reaction barrier.

Electrodeposition is a novel method for fabrication of diamond-like carbon (DLC) films on metal substrates. In this work, DLC was electrochemically deposited on different substrates based on an anodic oxidation cyclization of acetylene in liquid ammonia. Successfully anodic deposition was carried out for DLC onto nickel substrate at temperatures below -40°C. Comparative studies were performed on a series of different carbon sources (acetylene, sodium acetylide, and a mixture of acetylene and sodium acetylide). The films were characterized using a variety of methods including Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), XPS valence band spectra, and/or scanning electron microscopy (SEM). Raman spectroscopy is used as a bench mark technique to verify the presence of deposited DLC films, to access the films homogeneities, and to provide the ratio of the different carbon phases, mainly disordered graphite (D) and graphite (G) phases in the films. A combination of the Raman with FTIR and valence band spectra analysis allowed the distinction between hydrogenated DLC and unhydrogenated DLC films. Three different kinds of DLC [(1) hydrogenated DLC (a-C:H); (2) tetrahedral hydrogenated DLC (ta-C:H); and (3) graphitic-like DLC] were deposited depending upon the deposition conditions and substrates. Temperature and current density are …

Electrodeposition method is used to deposit diamond-like carbon (DLC) films on copper substrates via anodic oxidation at low temperature. These films are characterized using Raman spectroscopy, Fourier transform infrared spectroscopy and scanning electron microscopy. Homogeneity of these films is studied using Raman spectroscopy and scanning electron microscopy. Scotch tape peel tests indicate adherent film on copper substrate. Carbon phase transformation is studied using thermal annealing experiments in conjunction with Raman spectroscopy and scanning electron microscopy. A cathodic electrochemical method is also studied to deposit diamond-like carbon films on copper substrates. However, films deposited by the cathodic route have poor adhesion and quality compared to anodically deposited films. It is also possible to grow diamond phase on copper substrates using acetylene in liquid ammonia via electrodeposition route. An electrochemical method is proposed for boron doping into DLC films.