We describe the goals and research program leading to the Heavy Ion Integrated Research Experiment (IRE). We review the basic constraints which lead to a design and give examples of parameters and capabilities of an IRE. We also show design tradeoffs generated by the systems code IBEAM.

The photon plus missing energy signature is a primary handle on two important classes of theories. Theories with large extra dimensions predict the production of photons in association with Kaluza-Klein excitations of the graviton. In supersymmetric theories with superlight gravitinos, photons can be produced in association with gravitino pairs. The signatures for these two theories are compared, and it is found that they can be distinguished by studying the photon energy distributions and scaling of the cross section with center-of-mass energy. Both these methods fail, however, if there are six extra dimensions. In that case, additional phenomena predicted by the theories would be required to narrow down the underlying causes of the photon plus missing energy signal. We also study the ability of these measurements to determine the number of extra dimensions.

A recent trend in distributed computing is the construction of high-performance distributed systems called computational grids. One difficulty we have encountered is that there is no standard format for the representation of performance information and no standard protocol for transmitting this information. This limits the types of performance analysis that can be undertaken in complex distributed systems. To address this problem, we present an XML-based protocol for transmitting performance events in distributed systems and evaluate the performance of this protocol.

In this paper, we report on gamma ray and thermal neutron detection with RbGd2Br7:Ce scintillators. RbGd2Br7:Ce (RGB) is a new scintillator material, which shows high light output (56,000 photons/MeV) and has a fast principal decay constant (45 ns) when doped with 10 percent Ce. These properties make RGB an attractive scintillator for g-ray detection. Also, due to the presence of Gd as a constituent, RGB has a high cross section for thermal neutron absorption and can achieve close to 100 percent stopping efficiency with 0.5 mm thick RGB crystals. Crystals of RGB with three different Ce concentrations (0.1, 5, and 10 percent) have been grown and their basic scintillation properties such as light output, decay time, and emission spectrum have been measured. In addition, high efficiency thermal neutron detection has been confirmed in our studies.

When Fluor Fernald took over the management of the Fernald Environmental Management Project in 1992, the estimated closure date of the site was more than 25 years into the future. Fluor Fernald, in conjunction with DOE-Fernald, introduced the Accelerated Cleanup Plan, which was designed to substantially shorten that schedule and save taxpayers more than $3 billion. The management of Fluor Fernald believes there are three fundamental concerns that must be addressed by any contractor hoping to achieve closure of a site within the DOE complex. They are relationship management, resource management and contract management. Relationship management refers to the interaction between the site and local residents, regulators, union leadership, the workforce at large, the media, and any other interested stakeholder groups. Resource management is of course related to the effective administration of the site knowledge base and the skills of the workforce, the attraction and retention of qualified a nd competent technical personnel, and the best recognition and use of appropriate new technologies. Perhaps most importantly, resource management must also include a plan for survival in a flat-funding environment. Lastly, creative and disciplined contract management will be essential to effecting the closure of any DOE site. Fluor Fernald, together with …

Plasma immersion ion implantation (PIII) offers high throughput and efficiency in the synthesis of silicon-on-insulator (SOI) materials. In the separation by plasma implantation of oxygen (SPIMOX) process, the spatial and time variation of the sample temperature must be known and well controlled to ensure uniform buried oxide and silicon overlying layer thicknesses over the entire silicon wafer. In this paper, we describe a two-dimensional model and derive the temperature distribution on the silicon wafer with respect to time and other process parameters. Our results show laterally non-uniform heating by the incoming ions and the local temperature is influenced more by the sample voltage and thermal irradiation coefficient of the target than the pulse duration and plasma density. The model provides a simple and quick means to determine whether external heating will be needed to maintain the sample temperature at 600 C during the SPIMOX process.

The Spallation Neutron Source (SNS) project is a collaborative effort between Brookhaven, Argonne, Jefferson, Lawrence Berkeley, Los Alamos and Oak Ridge National Laboratories. Los Alamos is responsible for the design of the linac for this accelerator complex. The code PARMILA, developed at Los Alamos is widely used for proton linac design and beam dynamics studies. The most updated version includes superconducting structures among others. In recent years, some other codes have also been developed which primarily focuses on the studies of the beam dynamics. In this paper, we compare the simulation results and discuss physics aspects of the different linac design and beam dynamics simulation codes.

Methods are being developed for demonstrating that nonstandard high-level radioactive waste (HLW) forms meet the intent of the product consistency requirement in the Waste Acceptance System Requirements document (WASRD). That requirement was established for borosilicate HLW glasses ''to ensure a consistent glass product by controlling the vitrification process, consistency is necessary to reflect consideration for the waste package designs.'' [1] The test method specified in the WASRD for HLW glasses is the 7-day product consistency test (PCT). To meet the WASRD requirement, the response of an HLW glass in the PCT must be less than that of the environmental assessment (EA) glass. The EA glass is used as a benchmark ''so that conservative but realistic assessments of the engineered barrier system performance can be made.'' [1] The PCT and the WASRD requirement were developed to bound the behaviors of the wide range of borosilicate HLW glasses that will be produced at DOE facilities for the purpose of repository design. However, the need to demonstrate that the physical, chemical, and radiological properties of HLW forms have been constrained within acceptable (i.e., as-qualified) ranges will probably apply to all HLW waste forms. The PCT may not be the appropriate method for nonstandard …

Calcium and chloride are necessary cofactors for the proper function of the oxygen-evolving complex (OEC) of Photosystem II (PS II). Located in the thylakoid membranes of green plants, cyanobacteria and algae, PS II and the OEC catalyze the light-driven oxidation of water into dioxygen (released into the biosphere), protons and electrons for carbon fixation. The actual chemistry of water oxidation is performed by a cluster of four manganese atoms, along with the requisite cofactors Ca{sup 2+} and Cl{sup -}. While the Mn complex has been extensively studied by X-ray absorption techniques, comparatively less is known about the Ca{sup 2+} cofactor. The fewer number of studies on the Ca{sup 2+} cofactor have sometimes relied on substituting the native cofactor with strontium or other metals, and have stirred some debate about the structure of the binding site. past efforts using Mn EXAFS on Sr-substituted PSII are suggestive of a close link between the Mn cluster and Sr, within 3.5 {angstrom}. The most recent published study using Sr EXAFS on similar samples confirms this finding of a 3.5 {angstrom} distance between Mn and Sr. This finding was base3d on a second Fourier peak (R {approx} 3 {angstrom}) in the Sr EXAFS from functional …

Direct measurement of the coherence time of a high-intensity laser beam (600 ps, 10{sup 14} W.cm{sup -2}) after plasma propagation is achieved using a Michelson interferometer. Through plasma of interest for indirect-drive fusion (0.1 x n{sub c}, 1 mm long), a large decrease of the coherence time is observed, from 100 ps to {approx} 10 ps, induced by the interaction between the intense beam and the plasma. This decrease is even stronger as the light is scattered at larger angles from the initial beam angular distribution and as the plasma density is increased. The results coincide with trends observed in recent numerical simulations.

Diabetes is a disease that affects over 16 million people in the USA at a cost of 100 billion dollars annually. The ability to regulate insulin delivery in people with Type 1 diabetes is imperative as is the need to manage glucose levels in all people with this disease. Our current method for monitoring glucose is a (FDA approved) minimally invasive enzymatic sensor that can measure glucose levels in vivo for three days. We are focused on developing a noninvasive implantable glucose sensor that will be interrogated by an external device. The material must be robust, easy to process, biocompatible and resistant to biofouling. In this Presentation we will discuss the development of a new polymeric matrix that can recognize physiological levels of glucose in vitro using fluorescent spectroscopy.

Cluster computing has emerged as a defacto standard in parallel computing over the last decade. Now, researchers have begun to use clustered, shared-memory multiprocessors (SMPs) to attack some of the largest and most complex scientific calculations in the world today [2, 1], running them on the world's largest machines including the US DOE ASCI platforms: Red, Blue Mountain, Blue Pacific, and White. MPI has been the predominant programming model for clusters [3]; however, as users move to ''wider'' SMPs, the combination of MPI and threads has a ''natural fit'' to the underlying system design: use MPI for managing parallelism between SMPs and threads for parallelism within one SMP. OpenMP is emerging as a leading contender for managing parallelism within an SMP. OpenMP and MPI offer their users very different characteristics. Developed for different memory models, they fill diametrically opposed needs for parallel programming. OpenMP was made for shared memory systems, while MPI was made for distributed memory systems. OpenMP was designed for explicit parallelism and implicit data movement, while MPI was designed for explicit data movement and implicit parallelism. This difference in focus gives the two parallel programming frameworks very different usage characteristics. But these complementary usage characteristics make the …

An alternative approach is described to evaluate the statistical nature of the breakup of shaped charge liners. Experimental data from ductile and brittle copper jets are analyzed in terms of velocity gradient, deviation of {Delta}V from linearity, R/S analysis, and the Hurst exponent within the coupled map lattice model. One-dimensional simulations containing 600 zones of equal mass and using distinctly different force-displacement curves are generated to simulate ductile and brittle behavior. A particle separates from the stretching jet when an element of material reaches the failure criterion. A simple model of a stretching rod using brittle, semi-brittle, and ductile force-displacement curves is in agreement with the experimental results for the Hurst exponent and the phase portraits and indicates that breakup is a correlated phenomenon.

Advances in computational capability and modeling techniques, as well as improvements in experimental characterization methods offer the possibility of directly comparing modeling and experiment investigations of irradiation effects in metals. As part of a collaboration among the Instituto de Fusion Nuclear (DENIM), Lawrence Livermore National Laboratory (LLNL) and CIEMAT, single and polycrystalline {alpha}-Fe samples have been irradiated with 150 keV Fe-ions to doses up to several dpa. The irradiated microstructure is to be examined with both transmission electron microscopy (TEM) and positron annihilation spectroscopy (PAS). Concurrently, we have modeled the damage accumulation in Fe under these irradiation conditions using a combination of molecular dynamics (MD) and kinetic Monte Carlo (KMC). We aim to make direct comparison between the simulation results and the experiments by simulating TEM images and estimating positron lifetimes for the predicted microstructures. While the identity of the matrix defect features cannot be determined from TEM observations alone, we propose that both large self-interstitial loops, trapped at impurities within the material, and small, spherical nanovoids form.

We present position sensitivity measurements obtained with one of the 32-fold segmented HPGe detectors from Michigan State University. These measurements were performed with a collimated beam of {sup 137}Cs gamma rays scattered by 90 degrees. This deposits 374 keV at a given location inside the crystal. A position resolution can be determined over many events by examining the digitally recorded pulse shapes on the 32 electrical contacts. If position resolution is adequate, gamma ray Compton camera imaging may be possible.

We suggest a new class of high-flux renewable optics, in particular, for the use at the X-ray free electron laser, LCLS, which is under discussion now. The size of optical elements we have in mind is from a fraction of a square centimeter to a few square centimeters. We suggest that working fluid be pressed through a porous substrate (made, e.g., of fused capillaries) to form a film, a few tens to a hundred microns thick. After the passage of an intense laser pulse, the liquid film is sucked back through the substrate by a reversed motion of the piston, and formed anew before the next pulse. The working surface of the film is made flat by capillary forces. We discuss the role of viscous, gravitational, and capillary forces in the dynamics of the film and show that the properly made film can be arbitrarily oriented with respect to the gravitational force. This makes the proposed optics very flexible. We discuss effects of vibrations of the supporting structures on the quality of optical elements. Limitations on the radiation intensity are formulated. We show how the shape of the film surface can be controlled by electrostatic and magnetic forces, allowing one …

Properties of rock materials under quasistatic conditions are well characterized in laboratory experiments. Unfortunately, quasistatic data alone are not sufficient to calibrate models for use to describe inelastic wave propagation associated with conventional and nuclear explosions, or with impact. First, rock properties are size-dependent. properties measured using laboratory samples on the order of a few centimeters in size need to be modified to adequately describe wave propagation in a problem on the order of a few hundred meters in size. Second, there is lack of data about the damage (softening) behavior of rock because most laboratory tests focus on the pre-peak hardening region with very little emphasis on the post-peak softening region. This paper presents a model for granite that accounts for both the hardening and softening of geologic materials, and also provides a simple description of rubblized rock. The model is shown to reproduce results of quasistatic triaxial experiments as well as peak velocity and peak displacement attenuation from a compendium of dynamic wave propagation experiments that includes US and French nuclear tests in granite.

The Central Solenoid Model Coil (CSMC) was designed and built from 1993 to 1999 by an ITER collaboration between the US and Japan, with contributions from the European Union and the Russian Federation. The main goal of the project was to establish the superconducting magnet technology necessary for a large-scale fusion experimental reactor. Three heavily instrumented insert coils were built to cover a wide operational space for testing. The CS Insert, built by Japan, was tested in April-August of 2000. The TF Insert, built by Russian Federation, will be tested in the fall of 2001. The NbAl Insert, built by Japan, will be tested in 2002. The testing takes place in the CSMC Test Facility at the Japan Atomic Energy Research Institute, Naka, Japan. The CSMC was charged successfully without training to its design current of 46 kA to produce 13 T in the magnet bore. The stored energy at 46 kA was 640 MJ. This paper presents the main results of the CSMC and the CS Insert testing--magnet critical parameters, ac losses, joint performance, quench characteristics and some results of the post-test analysis.

Under the Situation and Crisis Center (SCC) management, the Information Analytical Center (IAC) of the Ministry of Atomic Energy (Minatom) of Russia was created to oversee the operation of the Federal Nuclear Material Control and Accounting Information System (FIS). During 2000, the FIS achieved an important milestone in its development: the basic functions of the information system were implemented. This includes placing into operation the collecting and processing of nuclear material control and accounting (MC&A) information from the enterprises reporting to the FIS. The FIS began working with 14 Russian enterprises to develop and implement full-function reporting (i.e., reporting inventory and inventory changes including closeout and reconciliation between the FIS and enterprises). In 2001, the system will expand to include enterprise-level inventory information for all enterprises using nuclear materials in Russia. For this reason, at the end of 2000 through the beginning of 2001, five separate training sessions were held for over 100 enterprise personnel responsible for preparation and transfer of the reports to the FIS. Through the assistance of the Nuclear Material Protection, Control and Accounting (MPC&A) program, information systems for the accounting of nuclear materials are being installed at Russia enterprises. In creating the program for modernization of …

Low-power EM radar-like sensors have made it possible to measure properties of the human speech production system in real-time, without acoustic interference [1]. By combining these data with the corresponding acoustic signal, we've demonstrated an almost 10-fold bandwidth reduction in speech compression, compared to a standard 2.4 kbps LPC10 protocol used in the STU-III (Secure Terminal Unit, third generation) telephone. This paper describes a potential EM sensor/acoustic based vocoder implementation.

In the past year a spare NASA/GSFC Astro-E microcalorimeter has been installed, tested, and run successfully on the electron beam ions traps EBIT-I and EBIT-II at the Lawrence Livermore National Laboratory. The microcalorimeter complements crystal and grating spectrometers already part of the LLNL ebit program making it possible to measure a broad bandwidth ({approx}0.3-10 keV) with moderate resolution while simultaneously measuring a narrow bandwidth ({approx}0.7-1.3 keV) with high resolution. An overview of recent work, including measurements by the microcalorimeter of absolute excitation cross is presented. These results continue our effort to provide atomic data of high quality to be used as benchmarks of theoretical calculations and to be included in atomic data bases employed by spectral fitting packages used to interpret spectra obtained by XMM-Newton and the Chandra X-Ray Observatory.

Neutron hardening and embrittlement of pressure vessel steels is due to a high density of nanometer scale features, including Cu-rich precipitates which form as a result of radiation enhanced diffusion. High-energy displacement cascades generate large numbers of both isolated point defects and clusters of vacancies and interstitials. The subsequent clustering, diffusion and ultimate annihilation of primary damage is inherently coupled with solute transport and hence, the overall chemical and microstructural evolutions under irradiation. In this work, we present atomistic simulation results, based on many-body interatomic potentials, of the migration of vacancies, solute and self-interstitial atoms (SIA) in pure Fe and binary Fe-0.9 and 1.0 at.% Cu alloys. Cu diffusion occurs by a vacancy mechanism and the calculated Cu diffusivity is in good agreement with experimental data. Strain field interactions between the oversized substitutional Cu solute atoms and SIA and SIA clusters are predominantly repulsive and result in both a decreased activation energy and diffusion pre-factor for SIA and small (N < 5) SIA cluster migration, which occurs by three-dimensional motion. The Cu appears to enhance the reorientation of the SIA clusters to different <111> directions, as well as the transition from <110> to mobile <111> configurations. The migration behavior of …

LOTIS (Livermore Optical Transient Imaging System) and Super-LOTIS are automatic telescope systems that measure very prompt optical emission occurring within seconds of the gamma-ray energy release during a Gamma Ray Burst (GRB). Unlike hour-to-days delayed afterglow measurements, very early measurements will contain information about the GRB progenitor. To accomplish this, we developed and have been operating automated telescopes that rapidly image GRB coordinate error boxes in response to triggers distributed by the GRB Coordinate Distribution Network (GCN). LOTIS, located in California, consists of 4 cameras each with a different astronomical filter (B, V, R, open) that can respond to GRB triggers within 5 s. Super-LOTIS can point to any part of the sky within 30 s upon receipt of a GCN trigger and its sensitivity is as deep as V = 17-19 depending on the integration times. Since the shutdown of the CGRO, there has been no real-time GRE3 triggers that enable the LOTIS systems to measure real-time GRE3 counterpart fluxes as of May 2001. This paper describes performance of these systems. We also present our plan to replace the current optical CCD camera on the Super-LOTIS to a near infrared camera to be able to probe dusty GRB environment.

The Russian Federation Ministry of Atomic Energy (Minatom) is the federal authority empowered with the management of state-owned nuclear materials, with the exception of military applications. The Russian Federal Nuclear Materials Control and Accounting Information System (FIS) is a key component in establishing an effective nuclear materials management system in the Russian Federation. In December 2000, the Russian government issued the decree to enter into force the regulation on the accounting and control of nuclear materials and directed the State System of Accounting and Control (SSAC) of nuclear materials should begin October 2001. This regulation establishes the basic accounting documents and the requirement to report them to the FIS to launch the State Nuclear Material Registry of nuclear materials. The Nuclear Material Registry contains information on agencies and operating organizations that use nuclear material, along with the kinds, quantity and other characteristics of nuclear material. Minatom will use the Registry and the supporting database and functionality that reside in the FIS for carrying out the functions of nuclear materials management. At the same time, the FIS provides for reporting from material balance areas (MBA). With American support, 14 Russian enterprises are reporting material balance area level information to the FIS …