This project describes a novel rotating-disc reactor has been designed and built to enable modulated flux deposition of CuInSe2 and its related binary compounds. The reactor incorporates both a thermally activated source and a novel plasma-activated source of selenium vapor, which have been used for the growth of epitaxial and polycrystalline thin-film layers of CuInSe2. A comparison of the different selenium reactant sources has shown evidence of increases in its incorporation when using the plasma source, but no measurable change when the thermally activated source was used. We concluded that the chemical reactivity of selenium vapor from the plasma source is significantly greater than that provided by the other sources studied. Epitaxially grown CuInSe2 layers on GaAs, ZnTe, and SrF2 demonstrate the importance of nucleation effects on the morphology and crystallographic structure of the resulting materials. These studies have resulted in the first reported growth of the CuAu type-I crystallographic polytype of CuInSe2, and the first reported epitaxial growth of CuInSe2 on ZnTe. Polycrystalline binary (Cu,Se) and (In,Se) thin films have been grown, and the molar flux ratio of selenium to metals was varied. It is shown that all of the reported binary compounds in each of the corresponding binary …

Fermilab and other DOE high energy physics laboratories are studying the possibility of a Very Large Hadron Collider (VLHC) for operation in the post-LHC era. The current VLHC design [1] foresees a 2-staged approach, where the second stage (referred to as VLHC-2) has a proton energy up to 100 TeV at a peak luminosity of 2{center_dot}10{sup 34} cm{sup {minus}2} sec{sup {minus}1}. The protons are guided through a large 233 km circumference ring with 10 T bending magnets using Nb{sub 3}Sn superconductor at 5 K. The synchrotron radiation (SR) power emitted by the beam in such a machine is {approx}5 W/m/beam [1]. However, other VLHC scenarios (e.g. [2]) with smaller rings and higher luminosity result in SR power levels exceeding this value, reaching 10 or even 20 W/m/beam. Intercepting and removing this power in a cryogenic environment is a major challenge. In this paper a discussion of SR in the VLHC-2, and various approaches to the issue, are presented. One possibility is the use of a beam screen (BS) to intercept the synchrotron radiation power. The BS operating temperature is chosen to balance thermodynamic efficiency, cryogenic-, vacuum-, beam-stability- and magnet-aperture issues. Another approach is to intercept the radiation in discrete points …

Daily newspaper from Perry, Oklahoma that includes local, state, and national news along with advertising.

Daily newspaper from Chickasha, Oklahoma that includes local, state, and national news along with advertising.

Daily newspaper from Altus, Oklahoma that includes local, state, and national news along with advertising.

Daily newspaper from Baytown, Texas that includes local, state, and national news along with advertising.

The National Museum of the Pacific War presents an oral interview with Charles Clevenger. Clevenger was born in Fulton County, Indiana in May 1925 and enlisted in the Marine Corps in March 1944. Following boot camp and communications training in January 1945, he embarked aboard the USS Meriwether (APA-203) in San Diego and sailed to Pearl Harbor. He boarded another troopship in Hawaii and sailed to Saipan. Clevenger then boarded USS LST-641 bound for Okinawa. During that transit the LST sailed through a typhoon. He was assigned to the 1st Provisional Anti-aircraft Artillery Group of III Amphibious Corps and landed on Okinawa on 5 April 1945. His group operated 90mm artillery and he describes the features of the radar system. His duties included communicating by radio and telephone with other anti-aircraft batteries on the island. He frequently heard Tokyo Rose broadcasting American music. He had several close calls with Japanese bombers and was on Okinawa when Japan surrendered. He was transferred to the First Marine Division and embarked on the USS Randall (APA-224) on 30 September bound for China. His convoy encountered nearly 1,000 mines in the Yellow Sea. He was badly burned while in China, but soon recovered and …

The National Museum of the Pacific War presents an oral interview with Charles Clevenger. Clevenger was born in Fulton County, Indiana in May 1925 and enlisted in the Marine Corps in March 1944. Following boot camp and communications training in January 1945, he embarked aboard the USS Meriwether (APA-203) in San Diego and sailed to Pearl Harbor. He boarded another troopship in Hawaii and sailed to Saipan. Clevenger then boarded USS LST-641 bound for Okinawa. During that transit the LST sailed through a typhoon. He was assigned to the 1st Provisional Anti-aircraft Artillery Group of III Amphibious Corps and landed on Okinawa on 5 April 1945. His group operated 90mm artillery and he describes the features of the radar system. His duties included communicating by radio and telephone with other anti-aircraft batteries on the island. He frequently heard Tokyo Rose broadcasting American music. He had several close calls with Japanese bombers and was on Okinawa when Japan surrendered. He was transferred to the First Marine Division and embarked on the USS Randall (APA-224) on 30 September bound for China. His convoy encountered nearly 1,000 mines in the Yellow Sea. He was badly burned while in China, but soon recovered and …

The purpose of the research funded under this study grant was to investigate the feasibility of a small scale experiment to test the concept of centrifugal confinement as a magnetic fusion energy scheme and to develop conceptual designs for important components of such an experiment. This work falls in the category of Innovative Confinement Concepts, as defined by the Office of Fusion Energy. The results of the funded work were very successful in that various studies were conducted which showed the concept to be viable and these studies led to design improvements. In addition, the major components of an experiment were identified and designed at least to the conceptual stage. In September, 2000 the Maryland Centrifugal Torus was funded for construction, in no small part because of the progress made during the time period reported here. The centrifugal confinement concept for fusion is based on three principles: (1) centrifugal forces from supersonic plasma rotation perpendicular to a strong magnetic field can provide effective confinement along the field; (2) the concomitant large velocity shear will suppress even macro-MHD instabilities; and (3) the sheared rotation will heat the plasma via viscous dissipation. Technical progress was made in clarifying and quantifying these concepts …

The status of QCD studies at the Fermilab Tevatron are discussed. Specifically, the measurements of inclusive jet cross sections from the CDF and D0 collaborations are compared to theoretical predictions. New measurements in the forward rapidity regions are described and multijet results are discussed.

The design, construction, and bench testing of an X-band travelling-wave accelerating structure loaded with a permittivity=20 dielectric has been published recently by the Argonne Advanced Accelerator Group [1]. Here we describe a new program to build a test accelerator using this structure. The accelerator will be powered using high-power 11.424-GHz radiation available at the Magnicon Facility at the Naval Research Lab [2]. The magnicon is expected to provide up to 30 MW from each of two WR-90 output waveguide arms in pulses of up to 1-{micro}s duration, permitting tests of the dielectric-loaded X-band device at gradients of {approximately}40 MV/m. The use of higher power pulses (100-500 MW) eventually available at the output of an active pulse compressor [3] driven by the magnicon will permit gradients in excess of 100 MV/m to be achieved.

The effects of structural defects on the electrical activity of S doped GaN{sub x}As{sub 1-x} layers formed by S and N coimplantation in GaAs are reported. S and N ions were implanted to the depth of about 0.4 {micro}m. Electrochemical capacitance voltage measurements on samples annealed at 945 C for 10s show that in a thin (<0.1 {micro}m) surface layer the concentration of active shallow donors is almost an order of magnitude larger in S and N co-implanted samples than in samples implanted with S alone. The activation efficiency of S donors also shows a broad minimum at a depth of about 0.2 {micro}m below the surface. The results of these electrical measurements are correlated with the distribution of structural defects revealed by transmission electron microscopy (TEM). The TEM micrographs show that in addition to a band of dislocation loops commonly found in ion implanted GaAs, an additional band of small voids is observed in samples co-implanted with S and N. The location of this band correlates well with the region of reduced electrical activation of S donors, suggesting that formation of the voids through N accumulation results in a lower concentration of active, substitutional N atoms.

IN THE EVALUATION OF ODH, THE CALCULATION OF THE SPILL RATE FROM THE PRESSURIZED VESSEL IS THE CENTRAL TASK. THE ACCURACY OF THE ENGINEERING ESTIMATION BECOMES ONE OF THE SAFETY DESIGN ISSUES. THIS PAPER SUMMARIZES THE EQUATIONS FOR THE OXYGEN CONCENTRATION CALCULATION IN DIFFERENT CASES, AND DISCUSSES THE EQUATIONS FOR THE GAS RELEASE PROCESS CALCULATION BOTH FOR THE HIGH-PRESSURE GAS TANK AND THE LOW-TEMPERATURE LIQUID CONTAINER.

A five-watts G-M/J-T refrigerator was built and installed for the high-energy physics research at Brookhaven National Laboratory in 2001. A liquid helium target of 8.25 liters was required for an experiment in the proton beam line at the Alternating Gradient Synchrotron (AGS) of BNL. The large radiation heat load towards the target requires a five-watts refrigerator at 4.2 K to support a liquid helium flask of 0.2 meter in diameter and 0.3 meter in length which is made of Mylar film of 0.35 mm in thickness. The liquid helium flask is thermally exposed to the vacuum windows that are also made of 0.35 mm thickness Mylar film at room temperature. The refrigerator uses a two-stage Gifford-McMahon cryocooler for precooling the Joule-Thomson circuit that consists of five Linde-type heat exchangers. A mass flow rate of 0.8 {approx} 1.0 grams per second at 17.7 atm is applied to the refrigerator cold box. The two-phase helium flows between the liquid target and liquid/gas separator by means of thermosyphon. The paper presents the system design as well as the test results including the control of thermal oscillation.

This calculation has several purposes. First the calculation reduces the information contained in ''Committed Materials in Repository Drifts'' (BSC 2001a) to useable parameters required as input to MING V1.O (CRWMS M&O 1998, CSCI 30018 V1.O) for calculation of the effects of potential in-drift microbial communities as part of the microbial communities model. The calculation is intended to replace the parameters found in Attachment II of the current In-Drift Microbial Communities Model revision (CRWMS M&O 2000c) with the exception of Section 11-5.3. Second, this calculation provides the information necessary to supercede the following DTN: M09909SPAMING1.003 and replace it with a new qualified dataset (see Table 6.2-1). The purpose of this calculation is to create the revised qualified parameter input for MING that will allow {Delta}G (Gibbs Free Energy) to be corrected for long-term changes to the temperature of the near-field environment. Calculated herein are the quadratic or second order regression relationships that are used in the energy limiting calculations to potential growth of microbial communities in the in-drift geochemical environment. Third, the calculation performs an impact review of a new DTN: M00012MAJIONIS.000 that is intended to replace the currently cited DTN: GS9809083 12322.008 for water chemistry data used in the current …

Video footage from the KXAS-TV/NBC station in Fort Worth, Texas, to accompany a news story.

The purpose of the present work is to accurately measure the neutron cross sections of samarium. The most significant isotope is {sup 149}Sm, which has a large neutron absorption cross section at thermal energies and is a {sup 235}U fission product with a 1% yield. Its cross sections are thus of concern to reactor neutronics. Neutron capture and transmission measurements were performed by the time-of-flight technique at the Rensselaer Polytechnic institute (RPI) LINAC facility using metallic and liquid Sm samples. The capture measurements were made at the 25 meter flight station with a multiplicity-type capture detector, and the transmission total cross-section measurements were performed at 15- and 25-meter flight stations with {sup 6}Li glass scintillation detectors. Resonance parameters were determined by a combined analysis of six experiments (three capture and three transmission) using the multi-level R-matrix Bayesian code SAMMY version M2. The significant features of this work are as follows. Dilute samples of samarium nitrate in deuterated water (D{sub 2}O) were prepared to measure the strong resonances at 0.1 and 8 eV without saturation. Disk-shaped spectroscopic quartz cells were obtained with parallel inner surfaces to provide a uniform thickness of solution. The diluent feature of the SAMMY program was used …

Binary manipulation techniques are increasing in popularity. They support program transformations tailored toward certain program inputs, and these transformations have been shown to yield performance gains beyond the scope of static code optimizations without profile-directed feedback. They even deliver moderate gains in the presence of profile-guided optimizations. In addition, transformations can be performed on the entire executable, including library routines. This work focuses on program instrumentation, yet another application of binary manipulation. This paper reports preliminary results on generating partial data traces through dynamic binary rewriting. The contributions are threefold. First, a portable method for extracting precise data traces for partial executions of arbitrary applications is developed. Second, a set of hierarchical structures for compactly representing these accesses is developed. Third, an efficient online algorithm to detect regular accesses is introduced. These efforts are part of a larger project to counter the increasing gap between processor and main memory speeds by means of software optimization and hardware enhancements.

This two-page overview describes how the use of distributed energy resources at Federal facilities is being supported by the U.S. Department of Energy's (DOE's) Federal Energy Management Program (FEMP). Distributed energy resources include both existing and emerging energy technologies: advanced industrial turbines and microturbines; combined heat and power (CHP) systems; fuel cells; geothermal systems; natural gas reciprocating engines; photovoltaics and other solar systems; wind turbines; small, modular biopower; energy storage systems; and hybrid systems. DOE FEMP is investigating ways to use these alternative energy systems in government facilities to meet greater demand, to increase the reliability of the power-generation system, and to reduce the greenhouse gases associated with burning fossil fuels.

This four-page fact sheet describes distributed energy resources for Federal facilities, which are being supported by the U.S. Department of Energy's (DOE's) Federal Energy Management Program (FEMP). Distributed energy resources include both existing and emerging energy technologies: advanced industrial turbines and microturbines; combined heat and power (CHP) systems; fuel cells; geothermal systems; natural gas reciprocating engines; photovoltaics and other solar systems; wind turbines; small, modular biopower; energy storage systems; and hybrid systems. DOE FEMP is investigating ways to use these alternative energy systems in government facilities to meet greater demand, to increase the reliability of the power-generation system, and to reduce the greenhouse gases associated with burning fossil fuels.

Daily newspaper from Sapulpa, Oklahoma that includes local, state, and national news along with advertising.

Weekly newspaper from Alvin, Texas that includes local, state, and national news along with advertising.

During the past year, the CDF Experiment has reported on a variety of results concerning QCD and electroweak studies, studies of the top quark, and searches for new phenomena. A sample of these results is presented here.

Through the National Renewable Energy Laboratory (NREL), the United States Department of Energy (DOE) implemented the Wind Partnership for Advanced Component Technologies (WindPACT) program. This program will explore advanced technologies that may reduce the cost of energy (COE) from wind turbines. The initial step in the WindPACT program is a series of preliminary scaling studies intended to determine the optimum sizes for future turbines, help define sizing limits for certain critical technologies, and explore the potential for advanced technologies to contribute to reduced COE as turbine scales increase. This report documents the results of Technical Area 2-Turbine Rotor and Blade Logistics. For this report, we investigated the transportation, assembly, and crane logistics and costs associated with installation of a range of multi-megawatt-scale wind turbines. We focused on using currently available equipment, assembly techniques, and transportation system capabilities and limitations to hypothetically transport and install 50 wind turbines at a facility in south-central South Dakota.