Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen (LH{sub 2}) or ambient-temperature compressed hydrogen (CH{sub 2}). Insulated pressure vessels offer the advantages of liquid hydrogen tanks (low weight and volume), with reduced disadvantages (fuel flexibility, lower energy requirement for hydrogen liquefaction and reduced evaporative losses). The work described here is directed at verifying that commercially available pressure vessels can be safely used to store liquid hydrogen. The use of commercially available pressure vessels significantly reduces the cost and complexity of the insulated pressure vessel development effort. This paper describes a series of tests that have been done with aluminum-lined, fiber-wrapped vessels to evaluate the damage caused by low temperature operation. All analysis and experiments to date indicate that no significant damage has resulted. Required future tests are described that will prove that no technical barriers exist to the safe use of aluminum-fiber vessels at cryogenic temperatures. Future activities also include a demonstration project in which the insulated pressure vessels will be installed and tested on two vehicles. A draft standard will also be generated for obtaining certification for insulated pressure vessels.

A spare NASA/GSFC Astro-E microcalorimeter has been installed, tested, and run successfully on EBIT-II at the Lawrence Livermore National Laboratory. A brief overview of results including measurements by the microcalorimeter of absolute excitation cross sections, time dependent spectra, and spectra as a function of Maxwellian temperature are discussed.

In the transient diffraction NLYF proposal we set forward a program of work to investigate the response of crystals to shock compression in regions of strain rates previously unexplored, in a coordinated experimental, computational, and analytical program. Time resolved x-ray diffraction was used to directly determine the lattice parameters of crystals during shock loading previously on the Nova and Trident laser facilities. Under this proposal we extended this work to exploit the multi-beam direct drive capability of the Omega laser facility to allow more extensive diagnostic access for measuring the lattice parameters both parallel and perpendicular to the shock front. Under the NLUF Program in FY 99, we transitioned the dynamic diffraction experiments to the OMEGA facility. We developed a direct drive target configuration that uses a single beam to direct irradiate the surface of a thin crystal and 4 beams to irradiate a separate metal backlighter foil. Experiments were done with single crystal Si to demonstrate that the target design worked and that simultaneous measurements of compression both parallel and perpendicular to the shock propagation direction could be performed. We obtained simultaneous measurements of the (400) and (040) lattice planes during the period when a shock traveled through the …

We introduce a multi-layered image cache system that is designed to work with a pool of rendering engines to facilitate an interactive, frameless, asynchronous rendering environment. Our system decouples the rendering from the display of imagery. Therefore, it decouples render frequency and resolution from display frequency and resolution, and allows asynchronous transmission of imagery instead of the compute/send cycle of standard parallel systems. It also allows local, incremental refinement of imagery without requiring all imagery to be re-rendered. Images are placed in fixed position in camera (vs. world) space to eliminate occlusion artifacts. Display quality is improved by increasing the number of images. Interactivity is improved by decreasing the number of images.

The technique of using a nsec prepulse to create and ionize the plasma followed by a psec pulse to heat the plasma has enabled us to achieve saturated laser output for low-Z neon-like and nickel-like ions driven by small lasers with less than ten joules of energy. In this work we model recent experiments done using the COMET laser at Lawrence Livermore National Laboratory to illuminate slab targets of Pd up to 1.25 cm long with a 2 joule, 600 ps prepulse followed 700 psec later by a 6 joule, 6 psec drive pulse. The experiments measure the two-dimensional near-field and far-field laser patterns for the 14.7 nm Ni-like Pd x-ray laser line. This line has already demonstrated saturated output. The experiments are modeled using the LASNEX code to calculate the hydrodynamic evolution of the plasma and provide the temperatures and densities to the CRETIN code, which then does the kinetics calculations to determine the gain. Using a ray tracing code to calculate the near and far-field patterns, the simulations are then compared with experiments. We also present several new schemes that we are modeling. The first scheme is Pd-like Nd that has a promising 5d-5p laser line near 24.3 …

Due to their finite lifetime, muons must be accelerated very rapidly. It is challenging to make the magnets ramp fast enough to accelerate in a synchrotron, and accelerating in a linac is very expensive. One can use a recirculating accelerator (like CEBAF), but one needs a different arc for each turn, and this limits the number of turns one can use to accelerate, and therefore requires significant amounts of RF to achieve the desired energy gain. An alternative method for muon acceleration is using a fixed field alternating gradient (FFAG) accelerator. Such an accelerator has a very large energy acceptance (a factor of two or three), allowing one to use the same arc with a magnetic field that is constant over time. Thus, one can in principle make as many turns as one can tolerate due to muon decay, therefore reducing the RF cost without increasing the arc cost. This paper reviews the current status of research into the design of FFAGs for muon acceleration. Several current designs are described and compared. General design considerations are also discussed.

We have studied the non-ideal propagation of detonation waves in LX-10 and in the insensitive explosive TATB. Explosively-driven, 5.8-mm-diameter, 0.125-mm-thick aluminum flyer plates were used to initiate 38-mm-diameter, hemispherical samples of LX-10 pressed to a density of 1.86 g/cm{sup 3} and of TATB at a density of 1.80 g/cm{sup 3}. The TATB powder was a grade called ultrafine (UFTATB), having an arithmetic mean particle diameter of about 8-10 {micro}m and a specific surface area of about 4.5 m{sup 2}/g. Using PMMA as a transducer, output pressure was measured at 5 discrete points on the booster using a Fabry-Perot velocimeter. Breakout time was measured on a line across the booster with a streak camera. Each of the experimental geometries was calculated using the Ignition and Growth Reactive Flow Model, the JWL++ Model and the Programmed Burn Model. Boosters at both ambient and cold (-20 C and -54 C) temperatures have been experimentally and computationally studied. A comparison of experimental and modeling results is presented.

Ionization cooling lattices simultaneously require small beta-functions at the absorber and large energy acceptances to be effective. Simultaneously achieving these goals as well as having a good dynamic aperture requires that the lattice be relatively compact. If one wishes to avoid solenoids, one choice for creating such a lattice is to use combined-function magnets. These magnets can simultaneously focus in both planes, allowing one to achieve a low beta in both planes with a minimum number of magnets. In this paper we explore the design of lattices which contain only combined-function bending magnets using a thin-lens approximation, showing how to optimally achieve the requirements for muon cooling.

Cooling lattices consisting only of bends (using either rotated pole faces or gradient dipoles to achieve focusing) often require large apertures and short magnets. One expects the effect of end fields to be significant in this case. In this paper we explore the effect of adding end fields to a working lattice design that originally lacked them. The paper describes the process of correcting the lattice design for the added end fields so as to maintain desirable lattice characteristics. It then compares the properties of the lattice with end fields relative to the lattice without them.

No plant and animal species protected under the ESA, candidates for such protection, or species listed by the Washington state government were observed in the vicinity of the proposed sites. Piper's daisy may still occur in some of the burial grounds. This is a Washington State Sensitive plant species, and as such is a Level III resource under the Hanford Site Biological Resources Management Plan. Compensatory mitigation is appropriate for this species when adverse impacts cannot be avoided. The Ecological Compliance Assessment Project (ECAP) staff should consulted prior to the initiation of major work activities within areas where this species has been identified (218-E-12, 218-E-10). The stalked-pod and crouching milkvetch are relatively common throughout 200 West area, therefore even if the few individuals within the active burial grounds are disturbed, it is not likely that the overall local population will be adversely affected. The Watch List is the lowest level of listing for pl ant species of concern in the State of Washington. No adverse impacts to species or habitats of concern are expected to occur from routine maintenance within the active portions of the 218-W-4C, 218-W-4B, 218-W-3, 218-W-3A, and 218-W-5 burial grounds, as well as the portion of 218-E-12B …

This paper presents a description and analysis of a high-efficiency hydrogen production system. The main component of the system is a novel steam electrolyzer. In conventional electrolyzers, oxygen produced from electrolysis is usually released into the environment. In this design, natural gas is used to react with the oxygen produced in the electrolysis, reducing reduce the chemical potential difference across the electrolyzer, thus minimizing electricity consumption. The oxygen produced from the electrolysis is consumed in either a total oxidation or a partial oxidation reaction with natural gas. Experiments performed on single cells shown a voltage reduction as much as 1 V when compared to conventional electrolyzers. A heat recovery system (heat exchangers and catalytic converter) has been incorporated to the electrolyzer to obtain a high efficiency hydrogen production system. Results from a thermodynamic analysis show up to 70% efficiency with respect to primary energy source.

Diffractive lenses offer two potential advantages for very large aperture space telescopes; very loose surface-figure tolerances and physical implementation as thin, flat optical elements. In order to actually realize these advantages one must be able to build large diffractive lenses with adequate optical precision and also to compactly stow the lens for launch and then fully deploy it in space. We will discuss the recent fabrication and assembly demonstration of a 5m glass diffractive Fresnel lens at LLNL. Optical performance data from smaller full telescopes with diffractive lens and corrective optics show diffraction limited performance with broad bandwidths. A systems design for a 20m space telescope will be presented. The primary optic can be rolled to fit inside of the standard fairings of the Delta IV vehicle. This configuration has a simple deployment and requires no orbital assembly. A twenty meter visible telescope could have a significant impact in conventional astronomy with eight times the resolution of Hubble and over sixty times the light gathering capacity. If the light scattering is made acceptable, this telescope could also be used in the search for terrestrial planets.

An FFAG is a lattice with fixed magnetic fields that has an extremely wide energy acceptance. One particularly simple type of FFAG is based on a FODO lattice, where both quads can be combined-function bending/quadrupole magnets. The spaces between the combined-function magnets are left open for RF cavities and other hardware. This paper describes a general method for creating lattice designs for this type of lattice which gives the lattice optimal properties for an FFAG accelerator. The properties of this lattice as a function of input parameters are explored. The use of sextupoles to improve lattice properties is also explored.

Lanthanum calcium oxoborate (LaCOB) is a nonlinear optical material that belongs to the calcium-rare-earth (R) oxoborate family, with general composition CaRO(BO{sub 3}){sub 3} (R{sup 3+} = Sm, Gd, Lu, Y). X-ray photoemission, photoabsorption and resonant fluorescence were applied to study the electronic structure and surface chemistry of this material. High resolution photoemission measurements on the valence band electronic structure and La 3d and 4d, Ca 2p, B 1s and O 1s core lines were used to evaluate the surface and near surface chemistry. Element specific density of unoccupied electronic states in LaCOB were probed by x-ray absorption spectroscopy (XAS) at the La 3d (M4,5-edge), La 4d (N4,5-edge), B 1s and O 1s (K-edges) absorption edges. Soft x-ray fluorescence was used to further examine valence band states associated with spectral differences noted in the absorption measurements. These results provide the first measurements of the electronic structure and surface chemistry of this rare-earth oxoborate.

Vegetation will be mechanically removed from the 218-W-6 Low Level Burial Ground (LLBG). The 218-W-6 LLBG consists of shrub-steppe and herbaceous habitats. The Western meadowlark, killdeer, lark sparrow, and loggerhead shrike could nest in the project area, based on known nesting preferences. We recommend that vegetation removal on 218-W-6 occur outside the nesting season (i.e., August 1 through February 28), in order to avoid potential adverse impacts to nesting individuals and/or their young and to comply with the Migratory Bird Treaty Act.

Magnetic overlayers of Fe and Co have been investigated with X-ray Magnetic Circular Dichroism in X-ray Absorption Spectroscopy (XMCD-ABS) and Photoelectron Spectroscopy (PES), including Spin-Resolved Photoelectron Spectroscopy (SRPES), at Beamline 4 at the Advanced Photon Source (APS). Particular emphasis was placed upon the interrogation of the 2p levels of the Fe.

The implementation in TRANSP of a recent version of TORIC capable of calculating power deposition for HHFW conditions is used to analyze NSTX plasma under different operating conditions. The power deposition profile into the electrons is obtained for high-Te conditions - Te ≤ 5keV - obtained in He and D plasmas with ITB. HHFW heating of NBI-induced H-mode plasmas is discussed. At the RF onset the RF power is divided evenly between the electrons and the fast particles, but as the latter thermalize and the electron density increases, the HHFW power repartition shifts progressively toward the electrons. Power deposition profiles for the electrons and for the fast particles are shown.

The Performance Engineering Institute (PERI) originally proposed a tiger team activity as a mechanism to target significant effort optimizing key Office of Science applications, a model that was successfully realized with the assistance of two JOULE metric teams. However, the Office of Science requested a new focus beginning in 2008: assistance in forming its ten year facilities plan. To meet this request, PERI formed the Architecture Tiger Team, which is modeling the performance of key science applications on future architectures, with S3D, FLASH and GTC chosen as the first application targets. In this activity, we have measured the performance of these applications on current systems in order to understand their baseline performance and to ensure that our modeling activity focuses on the right versions and inputs of the applications. We have applied a variety of modeling techniques to anticipate the performance of these applications on a range of anticipated systems. While our initial findings predict that Office of Science applications will continue to perform well on future machines from major hardware vendors, we have also encountered several areas in which we must extend our modeling techniques in order to fulfill our mission accurately and completely. In addition, we anticipate that …

The Hanford Seismic Assessment Program (HSAP) provides an uninterrupted collection of high-quality raw and processed seismic data from the Hanford Seismic Network for the U.S. Department of Energy and its contractors. The Hanford Seismic Assessment Team locates and identifies sources of seismic activity and monitors changes in the historical pattern of seismic activity at the Hanford Site. The data are compiled, archived, and published for use by the Hanford Site for waste management, natural phenomena hazards assessments, and engineering design and construction. In addition, the seismic monitoring organization works with the Hanford Site Emergency Services Organization to provide assistance in the event of a significant earthquake on the Hanford Site. The Hanford Seismic Network and the Eastern Washington Regional Network consist of 44 individual sensor sites and 15 radio relay sites maintained by the Hanford Seismic Assessment Team. For the Hanford Seismic Network, seven local earthquakes were recorded during the second quarter of fiscal year 2008. The largest event recorded by the network during the second quarter (February 3, 2008 - magnitude 2.3 Mc) was located northeast of Richland in Franklin County at a depth of 22.5 km. With regard to the depth distribution, two earthquakes occurred at shallow depths …

This report documents the deactivation, decontamination, decommissioning, and demolition of 16 buildings in the 300 Area of the Hanford Site. The D4 of these facilities included characterization, engineering, removal of hazardous and radiologically contaminated materials, equipment removal, utility disconnection, deactivation, decontamination, demolition of the structure, and stabilization or removal of the remaining slab and foundation as appropriate.

We will report results of an ongoing project in the Deschutes River Subbasin to describe Pacific lamprey (Lampetra tridentata) life history. Project objectives were to determine adult lamprey escapement from Sherars Falls located at Rkm 70.4 and determine lamprey focal spawning areas, spawn timing and habitat through radio telemetry. A mark-recapture study and tribal creel was conducted to determine adult escapement. Lamprey were radio tagged and are currently being mobile, aerial and fixed site tracked to describe spawning. Adult lamprey were collected at Sherars Falls using a long-handled dip net from June-September 2007. The fate of lamprey collected at Sherars Falls was determined based on girth measurements. Fish measuring less than 10.5 cm received two markings for the mark-recapture estimation while those measuring 10.5 cm or greater were implanted with radio transmitters. Two-hundred and nine lamprey were marked during first event sampling, 2,501 lamprey inspected for marks and 64 recaptured during second event sampling. We estimate lamprey abundance to be 8,083 (6,352-10,279) with a relative precision of 19.8. Tribal harvest was 2,303 +/- 88. Escapement was estimated at 5,780 adult lamprey. Thirty-six lamprey received radio transmitters. Lamprey were transported upstream 6.3 Rkm for surgery, held to recover from anesthesia and …

In Situ Gaseous Reduction is a technology currently being developed by DOE for the remediation of soil waste sites contaminated with hexavalent chromium. Prior work suggests that a candidate for application of this approach is the 183-DR site at Hanford. However, deep vadose zone drilling is needed to verify the presence of a hexavalent chromium source and to determine the concentration levels and spatial distribution of contamination. This document presents the requirements associated with drilling one to two vadose zone boreholes at the 183-DR site to obtain this information. If hexavalent chromium is determined to be present at levels of at least 10 ppm in the vadose zone in one of the initial boreholes, this hole will be completed for gas injection and six additional gas extraction boreholes will be drilled and completed. This network will be used as a flowcell for performing a gas treatment test at the site.

Experiments have been conducted on NSTX to study both steady state and perturbative mo mentum transport. These studies are unique in their parameter space under investigation, where the low aspect ratio of NSTX results in rapid plasma rotation with E x B shearing rates high enough to suppress low-k turbulence. In some cases, the ratio of momentum to energy confinement time is found to exceed five. Momentum pinch velocities of order 10-40 m/s are inferred from the measured angular momentum flux evolution after non-resonant magnetic perturbations are applied to brake the plasma.

Currently, there is considerable confusion within parts of the carbon dioxide capture and storage (CCS) technical and regulatory communities regarding the maturity and commercial readiness of the technologies needed to capture, transport, inject, monitor and verify the efficacy of carbon dioxide (CO2) storage in deep, geologic formations. The purpose of this technical report is to address this confusion by discussing the state of CCS technological readiness in terms of existing commercial deployments of CO2 capture systems, CO2 transportation pipelines, CO2 injection systems and measurement, monitoring and verification (MMV) systems for CO2 injected into deep geologic structures. To date, CO2 has been captured from both natural gas and coal fired commercial power generating facilities, gasification facilities and other industrial processes. Transportation via pipelines and injection of CO2 into the deep subsurface are well established commercial practices with more than 35 years of industrial experience. There are also a wide variety of MMV technologies that have been employed to understand the fate of CO2 injected into the deep subsurface. The four existing end-to-end commercial CCS projects – Sleipner, Snøhvit, In Salah and Weyburn – are using a broad range of these technologies, and prove that, at a high level, geologic CO2 storage …