The highlights of this report are: (1) fly ash classified by less than 100 microns in size was mixed into a 300 lb melt of alloy 535 without the need of a magnesium additive; (2) a vibratory feeder fitted with a sieve was used as the means to minimize particle clustering while introducing fly ash into the aluminum alloy 535 melt; and (3) the industrial-size field test was successful in that sand mold castings and permanent mold castings of tensile bars, K mold bars, and ingots were made from aluminum alloy 535-fly ash mix. Use of aluminum alloy 535 containing 7% magnesium precluded the need to introduce additional magnesium into the melt. The third round of sand mold castings as well as permanent mold castings produced components and ingots of alloy 535 instead of alloy 356. The ingots will be remelted and cast into parts to assess the improvement of flyash distribution which occurs through reheating and the solidification wetting process. Microstructure analysis continues on sand and permanent mold castings to study particle distribution in the components. A prototype sand cast intake manifold casting was found to be pressure tight which is a major performance requirement for this part. Another …

None

Current plans call for an alkaline scrub of actinide-bearing sludges in the Hanford Waste tanks prior to their incorporation in glass waste forms. Though it is assumed that actinides will remain in the sludge phase during this procedure, this assumption is based on insufficient supporting thermodynamic and kinetic data. In this project the authors will investigate the fundamental chemistry of actinides in strongly alkaline solution and solid phases to strengthen the foundation and identify potential limitations of this approach. They will focus on the characterization of the leaching of actinides from simulated BiPO{sub 4}, REDOX, and PUREX sludges, the identification of actinide mineral phases in the sludge simulants, and the possible solubilization of actinides by complexation and radiolysis effects. This program will provide new fundamental information on the chemical behavior and speciation of uranium, neptunium, plutonium, and americium in simulated alkaline tank waste sludges and alkaline scrub liquors. Sludge simulants will be prepared from the appropriate matrix components using published data for guidance. Actinide ions will be introduced in the oxidation states pertinent to process conditions. The authors will characterize the speciation of the actinides in the sludges using a variety of techniques. In parallel studies, they will address the …

Two major problems associated with Si-based MEMS devices are stiction and wear. Surface modifications are needed to reduce both adhesion and friction in micromechanical structures to solve these problems. In this paper, the authors will present a process used to selectively coat MEMS devices with tungsten using a CVD (Chemical Vapor Deposition) process. The selective W deposition process results in a very conformal coating and can potentially solve both stiction and wear problems confronting MEMS processing. The selective deposition of tungsten is accomplished through silicon reduction of WF{sub 6}, which results in a self-limiting reaction. The selective deposition of W only on polysilicon surfaces prevents electrical shorts. Further, the self-limiting nature of this selective W deposition process ensures the consistency necessary for process control. Selective tungsten is deposited after the removal of the sacrificial oxides to minimize process integration problems. This tungsten coating adheres well and is hard and conducting, requirements for device performance. Furthermore, since the deposited tungsten infiltrates under adhered silicon parts and the volume of W deposited is less than the amount of Si consumed, it appears to be possible to release stuck parts that are contacted over small areas such as dimples. Results from tungsten deposition …

The Configuration Management Plan for the Tank Farm Contractor describes configuration management the contractor uses to manage and integrate its technical baseline with the programmatic and functional operations to perform work. The Configuration Management Plan for the Tank Farm Contractor supports the management of the project baseline by providing the mechanisms to identify, document, and control the technical characteristics of the products, processes, and structures, systems, and components (SSC). This plan is one of the tools used to identify and provide controls for the technical baseline of the Tank Farm Contractor (TFC). The configuration management plan is listed in the management process documents for TFC as depicted in Attachment 1, TFC Document Structure. The configuration management plan is an integrated approach for control of technical, schedule, cost, and administrative processes necessary to manage the mission of the TFC. Configuration management encompasses the five functional elements of: (1) configuration management administration, (2) configuration identification, (3) configuration status accounting, (4) change control, and (5 ) configuration management assessments.

The objective of this work is to evaluate unqualified, water-level data gathered under the Nye County Early Warning Drilling Program (EWDP) and to determine whether the status of the data should be changed to ''qualified'' data in accordance with AP-SIII.2Q (Qualification of Unqualified Data and the Documentation of Rationale for Accepted Data). The corroboration method (as defined in Attachment 2 of AP-SIII.2Q) was implemented to qualify water-level data from Nye County measurements obtained directly from the Nye County Nuclear Waste Repository Program Office (NWRPO). Comparison of United States Geological Survey (USGS) measurements contained in DTN GS990608312312.003 with the Nye County water-level data has shown that the differences in water-level altitudes for the same wells are significantly less than 1 meter. This is an acceptable finding. Evaluation and recommendation criteria have been strictly applied to qualify Nye County measurements of water levels in selected wells measured by the USGS. However, the process of qualifying measured results by corroboration also builds confidence that the Nye County method for measurement of water levels is adequate for the intended use of the data (which is regional modeling). Therefore, it is reasonable to extend the term of ''qualified'' to water-level measurements in the remaining Nye …

A letter report issued by the General Accounting Office with an abstract that begins "Pursuant to a congressional request, GAO reviewed the Department of Veterans Affairs' (VA) compliance with the requirements to maintain capacity and access for veterans with special disabilities, focusing on: (1) the accuracy of the conclusions in VA's fiscal year (FY) 1998 annual capacity report; and (2) challenges facing VA in managing its special disability programs."

DYNA3D is an explicit, finite element code developed to solve high rate dynamic simulations for problems of interest to the engineering mechanics community. The DYNA3D code has been under continuous development since 1976[1] by the Methods Development Group in the Mechanical Engineering Department of Lawrence Livermore National Laboratory. The pace of code development activities has substantially increased in the past five years, growing from one to between four and six code developers. This has necessitated the use of software tools such as CVS (Concurrent Versions System) to help manage multiple version updates. While on-line documentation with an Adobe PDF manual helps to communicate software developments, periodically a summary document describing recent changes and improvements in DYNA3D software is needed. The first part of this report describes issues surrounding software versions and source control. The remainder of this report details the major capability improvements since the last publicly released version of DYNA3D in 1996. Not included here are the many hundreds of bug corrections and minor enhancements, nor the development in DYNA3D between the manual release in 1993[2] and the public code release in 1996.

There are several studies of optimal allocation of research and development resources over the time horizon of a project. The primary result of the basic noncompetitive models in this literature is that the optimal strategy is to choose a research intensity and ending date for the project such that the marginal costs of accelerating the project equals the marginal benefits of introducing the product sooner. This literature provides useful insights for the government planner who must allocate R&D resources for renewable energy development. However, several characteristics distinguish the process from the typical R&D planning problem. Specifically, with PV development, where the goal is to maximize the net present value of activities leading to cost reduction in commercial modules, there are (1) significant lag-times between investment in laboratory research and resulting effects in the marketplace, (2) a learning curve associated with the manufacturing process that also reduces the cost s of PV modules, (3) interim benefits from technical advances, (4) no clear end point to the R&D process, but rather a tapering off of the value of advances in technical efficiency, (5) significant uncertainty in the R&D process, (6) a family of products rather than an individual technology, (7) a co-mingling …

Correspondence issued by the General Accounting Office with an abstract that begins "Pursuant to a congressional request, GAO responded to congressional questions regarding GAO's testimony on the Equal Employment Opportunity (EEO) complaint process for federal employees, focusing on: (1) whether minorities are placed in positions that are "dead end employment tracks;" (2) whether GAO studied the Navy's Pilot Dispute Resolution Program, which is used to resolve EEO complaints; (3) whether the Equal Employment Opportunity Commission's (EEOC) Comprehensive Enforcement Program will be able to measure progress towards its goal of eradicating discrimination in the federal workplace; and (4) the prerequisites to a successful alternative dispute resolution (ADR) program."

A letter report issued by the General Accounting Office with an abstract that begins "Pursuant to a congressional request, GAO reviewed the role of the Department of Energy's power marketing administrations (PMA), focusing on: (1) how federal legislation and major relevant court cases have, over time, directed the PMAs to give preference to particular customers in purchasing electricity; and (2) the role of preference in the PMAs' electricity sales in light of the restructuring of the electricity industry."

From Abstract: This report covers using the Catalog of Federal Domestic Assistance, grant proposal writing, and print, Internet, and other sources of federal as well as private grants information.

The Plutonium Immobilization Program produces a ceramic wasteform that utilizes organic binders. Several techniques and instruments were developed to study binder burnout on full size ceramic samples in a production environment. This approach provides a method for developing process parameters on production scale to optimize throughput, product quality, offgas behavior, and plant emissions. These instruments allow for offgas analysis, large-scale TGA, product quality observation, and thermal modeling. Using these tools, results from lab-scale techniques such as laser dilametry studies and traditional TGA/DTA analysis can be integrated. Often, the sintering step of a ceramification process is the limiting process step that controls the production throughput. Therefore, optimization of sintering behavior is important for overall process success. Furthermore, the capabilities of this instrumentation allows better understanding of plant emissions of key gases: volatile organic compounds (VOCs), volatile inorganics including some halide compounds, NO{sub x}, SO{sub x}, carbon dioxide, and carbon monoxide.

This project seeks to understand the microscopic effects of radiation damage in nuclear waste forms. The authors' approach to this challenge encompasses studies of ceramics and glasses containing short-lived alpha- and beta-emitting actinides with electron microscopy, laser and X-ray spectroscopic techniques, and computational modeling and simulations. In order to obtain information on long-term radiation effects on waste forms, much of the effort is to investigate {alpha}-decay induced microscopic damage in 18-year old samples of crystalline yttrium and lutetium orthophosphates that initially contained {approximately} 1(wt)% of the alpha-emitting isotope {sup 244}Cm (18.1 y half life). Studies also are conducted on borosilicate glasses that contain {sup 244}Cm, {sup 241}Am, or {sup 249}Bk, respectively. The authors attempt to gain clear insights into the properties of radiation-induced structure defects and the consequences of collective defect-environment interactions, which are critical factors in assessing the long-term performance of high-level nuclear waste forms.

None

This report provides information on how Highly Migratory Species (HMS) like tunas, oceanic sharks, sailfishes, swordfishes, bill-fishes, and marlins are managed differently because of their migratory behavior. This includes information on which of these fish belongs to who basing on the jurisdiction on where these species migrate to. Updated April 21, 2000.

A nonradioactive chemical vapor space source term for tanks on the Phase 1 and the extended Phase 1 delivery, storage, and disposal mission was determined. Operations modeled included mixer pump operation and DST waste transfers. Concentrations of ammonia, specific volatile organic compounds, and quantitative volumes of aerosols were estimated.

Correspondence issued by the General Accounting Office with an abstract that begins "Pursuant to a congressional request, GAO provided information on the potential tax benefit individuals could receive as a result of a health insurance tax deduction proposed in H.R. 2990, focusing on: (1) GAO's estimation of both the number of people who would potentially be eligible for a tax deduction under this proposal; and (2) the potential value of such a deduction."

Reservation and adaptation are two well-known and effective techniques for enhancing the end-to-end performance of network applications. However, both techniques also have limitations, particularly when dealing with high-bandwidth, dynamic flows: fixed-capability reservations tend to be wasteful of resources and hinder graceful degradation in the face of congestion, while adaptive techniques fail when congestion becomes excessive. We propose an approach to quality of service (QoS) that overcomes these difficulties by combining features of reservations and adaptation. In this approach, a combination of online control interfaces for resource management, a sensor permitting online monitoring, and decision procedures embedded in resources enable a rich variety of dynamic feedback interactions between applications and resources. We describe a QoS architecture, GARA, that has been extended to support these mechanisms, and use three examples of application-level adaptive strategies to show how this framework can permit applications to adapt both their resource requests and behavior in response to online sensor information.

This is the first issue of the third volume (Spring 2000) of a technical bulletin produced for the Department of Energy's (DOE's) Federal Energy Management Program (FEMP). It is intended for Federal solar energy champions; that is, energy officers, contracting officials, facility managers, and others who plan or work on projects in which solar and other renewable energy technologies are installed in Federal government facilities, per the directives of Executive Order 13123 and the President's Million Solar Roofs Initiative. This issue contains an article about a new initiative led by DOE and the Department of the Interior/National Park Service; it involves obtaining more renewable energy systems for the national parks. Another article describes projects adding solar and wind systems to government facilities serving Native Americans, and there are other news items as well.

This document establishes the functional, performance, design, development, interface and test requirements for the Double-Shell Tank System.

This revision notes the supersedure of the subject document by concurrent issuance of HNF-1901 ''Technical Baseline Summary Description for the Tank Farm Contractor'', Revision 2. Safe storage mission technical baseline information was absorbed by the new revision of HNF-1901.

A letter report issued by the General Accounting Office with an abstract that begins "Pursuant to a congressional request, GAO: (1) reviewed the status of the Internal Revenue Service's (IRS) implementation of the taxpayer protection and rights provisions in title III of its Restructuring and Reform Act of 1998; and (2) determined what, if any, tax administration or other concerns IRS has identified in implementing these provisions."

This document is a revision of the document titled above, summarizing the technical baseline of the Tank Farm Contractor. It is one of several documents prepared by CH2M HILL Hanford Group, Inc. to support the U.S. Department of Energy Office of River Protection Tank Waste Retrieval and Disposal Mission at Hanford.