The focus of this research is to study the interaction between copper and the diffusion barrier/adhesion promoter. The behavior of copper sputter-deposited onto sputter-cleaned tantalum nitride is investigated. The data show that copper growth on tantalum nitride proceeds with the formation of 3-D islands, indicating poor adhesion characteristics between copper and Ta0.4N. Post-annealing experiments indicate that copper will diffuse into Ta0.4N at 800 K. Although the data suggests that Ta0.4N is effective in preventing copper diffusion, copper's inability to wet Ta0.4N will render this barrier ineffective. The interaction of copper with oxidized tantalum silicon nitride (O/TaSiN) is characterized. The data indicate that initial copper depositions result in the formation a conformal ionic layer followed by Cu(0) formation in subsequent depositions. Post-deposition annealing experiments performed indicate that although diffusion does not occur for temperatures less than 800 K, copper "de-wetting" occurs for temperatures above 500 K. These results indicate that in conditions where the substrate has been oxidized facile de-wetting of copper may occur. The behavior of a sputter-deposited Cu0.6Al0.4 film with SiO2 (Cu0.6Al0.4/SiO2) is investigated. The data indicate that aluminum segregates to the SiO2 interface and becomes oxidized. For copper coverages less than ~ 0.31 ML (based on a Cu/O …

The effect of substituents on the stabilities of cumulenes-ketenes, allenes, diazomethanes and isocyanates and related systems-alkynes, nitriles and nitrile oxides is studied using the density functional theory (B3LYP, SVWN and BP86) and ab initio (HF, MP2) calculations at the 6-31G* basis set level. Using isodesmic reactions, correlation between stabilization energies of cumulenes and substituent group electronegativities (c BE) is established and the results from DFT and MP2 methods are compared with the earlier HF calculations. Calculations revealed that the density functional methods can be used to study the effect of substituents on the stabilities of cumulenes. It is observed that the cumulenes are stabilized by electropositive substituent groups from s -electron donation and p -electron withdrawal and are destabilized by electronegative substituent groups from n-p donation. The calculated geometries of the cumulenes are compared with the available experimental data.High level ab initio and density functional theory calculations have been used to study the energetics of low-barrier hydrogen bond (LBHB) systems. Using substituted formic acid-formate anion complexes as model LBHB systems, hydrogen bond strength is correlated to the pKa mismatch between the hydrogen bond donor and the hydrogen bond acceptor. LBHB model systems are characterized by the 1H-NMR chemical shift calculations. …

The luminescence properties of Van Der Waals' dimers and clusters of pyrene and diazapyrene have been investigated. Excimers, dimeric species which are associative in an excited electronic state and dissociative in their ground state, have long been established and play an important role in many areas of photochemistry. My work here focuses on the luminescence and absorption properties of ground state dimers/aggregates, which are less understood, and allows further characterization of the ground state and excited state association of these aromatic molecules.

Aluminum was deposited onto both Teflon AF and Parylene AF surfaces by chemical vapor deposition of trimethylaluminum. This work shows that similar thin film (100 Angstroms) aluminum oxide adlayers form on both polymers at the low temperature dosing conditions used in the studies. Upon anneal to room temperature and above, defluorination of the polymer surfaces increased and resulted in fluorinated aluminum oxide adlayers; the adlayers were thermally stable to the highest temperatures tested (600 K). Angle-resolved spectra showed higher levels of fluorination toward the polymer/adlayer interface region. Copper films were also deposited at low temperature onto Teflon AF using a copper hexafluoroacetylacetonate-cyclooctadiene precursor. Annealing up to 600 K resulted in the loss of precursor ligands and a shift to metallic copper. As with aluminum adlayers, some polymer defluorination and resulting metal (copper) fluoride was detected. Parylene AF and polystyrene films surfaces were modified by directly dosing with water vapor passed across a hot tungsten filament. Oxygen incorporation into polystyrene occurred exclusively at aromatic carbon sites, whereas oxygen incorporation into parylene occurred in both aromatic and aliphatic sites. Oxygen x-ray photoelectron spectra of the modified polymers were comparable, indicating that similar reactions occurred. The surface oxygenation of parylene allowed enhanced reactivity …

The novel instrumentation of nanomanipulation coupled to nanospray mass spectrometry and its applications are presented. The nanomanipulator has the resolution of 10nm step sizes allowing for specific fine movement used to probe and characterize objects of interest. Nanospray mass spectrometry only needs a minimum sample volume of 300nl and a minimum sample size of 300attograms to analyze an analyte making it the ideal instrument to couple to nanomanipulation. The nanomanipulator is mounted to an inverted microscope and consists of 4 nano-positioners; these nano-positioners hold end-effectors and other tools used for manipulation. This original coupling has been used to enhance the current abilities of cellular probing and trace fiber analysis. Experiments have been performed to demonstrate the functionality of this instrument and its capabilities. Histidine and caffeine have been sampled directly from single fibers and analyzed. Lipid bodies from cotton seeds have been sampled indirectly and analyzed. The few applications demonstrated are only the beginning of nanomanipulation coupled to nanospray mass spectrometry and the possible applications are numerous especially with the ability to design and fabricate new end-effectors with unique abilities. Future study will be done to further the applications in direct cellular probing including toxicology studies and organelle analysis of …

Web-based homework systems are becoming more common in general chemistry as instructors face ever-increasing enrollment. Yet providing meaningful feedback on assignments remains of the utmost importance. Chemistry instructors consider completion of homework integral to students' success in chemistry, yet only a few studies have compared the use of Web-based systems to the traditional paper-and-pencil homework within general chemistry. This study compares the traditional homework system to four different Web-based systems. Data from eight, semester classes consisting of a diagnostic pre-test, final semester grades, and the number of successful and unsuccessful students are analyzed. Statistically significant results suggest a chemistry instructor should carefully consider options when selecting a homework system.

The development of the correlation consistent basis sets, cc-pVnZ (where n = D, T, Q, etc.) have allowed for the systematic elucidation of the intrinsic accuracy of ab initio quantum chemical methods. In density functional theory (DFT), where the cc-pVnZ basis sets are not necessarily optimal in their current form, the elucidation of the intrinsic accuracy of DFT methods cannot always be accomplished. This dissertation outlines investigations into the basis set requirements for DFT and how the intrinsic accuracy of DFT methods may be determined with a prescription involving recontraction of the cc-pVnZ basis sets for specific density functionals. Next, the development and benchmarks of a set of cc-pVnZ basis sets designed for the s-block atoms lithium, beryllium, sodium, and magnesium are presented. Computed atomic and molecular properties agree well with reliable experimental data, demonstrating the accuracy of these new s-block basis sets. In addition to the development of cc-pVnZ basis sets, the development of a new, efficient formulism of the correlation consistent Composite Approach (ccCA) using the resolution of the identity (RI) approximation is employed. The new formulism, denoted 'RI-ccCA,' has marked efficiency in terms of computational time and storage, compared with the ccCA formulism, without the introduction of …

A Series of fluorophores of the general formular P(CF2)nP and P(CF2)n-1CF3 has been synthesized. Copper catalyzed coupling of 1-bromopyrene and the corresponding mono and di-iodoperfluoroalkanes were used in most cases. For the n=3 dimer, a novel 1,w-perfluoroalkylation of pyrene via bis-decarboxylation of hexafluorogultaric acid was utilized. These compounds, along with suitable hydrocarbon analogs, are being used to study the flexibility of fluorocarbon chains using emission. We have found that the excimer formation for the fluorinated pyrene monomers is highly dependent on concentration and is less efficient than for pyene. Excimer formation for the fluorinated pyrene dimers is much more efficient than for the fluorocarbon monomers and is only slightly concentraion dependent. Steady-state emission spectra indicate hydrocarbon dimers-models form excimers more efficiently than the fluorinated dimers suggesting the fluorinated chains are stiffer than the hydrocarbons. We conducted the temperature-dependent studies and quantified the conformational difference.

The B3LYP density functional has been used to calculate properties of organometallic complexes of Co(CO)3 and ReBr(CO)3, with the chelating ligand 2,3-bisphosphinomaleic anhydride, in 19- and 18-electron forms. The SBKJC-21G effective core potential and associated basis set was used for metals (Co/Re) and the 6-31G* basis set was used for all other elements. The differences of bond angles, bond distances, natural atomic charges and IR vibrational frequencies were compared with the available experimental parameters. The differences between the 19- and 18-electron systems have been analyzed. The results reveal that the 19th electron is mostly distributed over the ligand of 2,3-bisphosphinomaleic anhydride, although partially localized onto the metal fragment in 1 and 2*. Two different methods, IR-frequencies and natural atomic charges, were used to determine the value of δ. Present computed values of δ are compared with available experimental values, and predictions are made for unknown complexes.

A 1H, 13C, and 6Li NMR study of 2-ethylhexyllithium showed that 2- ethylhexyllithium exists solely as a hexamer in cyclopentane solution over the temperature range from 25 to -65 °C. Furthermore, 2-ethylhexyllithium and lithium 2- ethyl-1-hexoxide were shown to form mixed aggregates when the alkoxide was formed in situ by reacting 2-ethylhexyllithium with 2-ethyl-1-hexanol. A multinuclear, variable temperature NMR study of a sample with an O:Li ratio of 0.2 led to the identification of at least four such aggregates, one of which was found to be a hexamer with the composition R5(RO)Li6. Studies of samples with higher O:Li ratios, up to 0.8, showed additional mixed aggregates present. All solutions containing mixed aggregates were also shown to contain hydrocarbon soluble lithium hydride. A study of lithium 2-ethyl-1- hexoxide indicated that it aggregates in solution as well.

This dissertation deals with two major topics that involve spectroscopic studies of (a) divalent group 10 metals and (b) silver(I)-phosphine complexes. The scope of the work involved the delineation of the electronic structure of these complexes in different environments and their use in electronic devices. The first topic is a look at the luminescence of tetrahedral silver(I)-phosphine complexes. Broad unstructured emissions with large Stokes shifts were found for these complexes. Computational analysis of the singlet and triplet state geometries suggests that this emission is due to a Jahn-Teller type distortion. The second topic represents the major thrust of this research, which is an investigation into the electronic structure of M(diimine)X2 (M= Pt(II), Pd(II), or Ni(II); X = dichloro, or dithiolate ligands) complexes and their interactions with an electron acceptor or Lewis acid. Chapter 3 assesses the use of some of these complexes in dye sensitized solar cells (DSSCs); it is shown that these complexes may lead to a viable alternative to the more expensive ruthenium-based dyes that are being implemented now. Chapter 4 is an investigation into donor/acceptor pairs involving this class of complexes, which serves as a feasibility test for the use of these complexes in organic photo-voltaics (OPVs) …

A synthetic approach to macromolecules of acetylenic arrays and luminescent properties is proposed and the execution of initial steps is described. Palladium-catalyzed coupling of 1,3,5-triiodobenzene with trimethylsilylbuta-1,3-diyne, trimethylsilylocta-1,3,5,7-tetrayne, and trimethylsilylhexadeca-1,3,5,7,9,11,13,15-octayne to yield the new 1,3,5-tris(trimethylsilylbuta-1,3-diynyl)benzene and the proposed 1,3,5-tris(8-(trimethylsilyl)octa-1,3,5,7-tetraynyl)benzene and 1,3,5-tris(trimethylsilyl)hexadeca-1,3,5,7,9,11,13,15-octaynyl)benzene respectively. The proposed three-coordinate Au (I) complexed macromolecules will be derived from the metallation of the aforementioned alkynylated arenes.

Calculations were performed on transition-metal complexes to (1) extrapolate the structure and bonding of the ground and phosphorescent states (2) determine the luminescence energies and (3) assist in difficult assignment of luminescent transitions. In the [Pt(SCN)4]2- complex, calculations determined that the major excited-state distortion is derived from a b2g bending mode rather than from the a1g symmetric stretching mode previously reported in the literature. Tuning of excimer formation was explained in the [Au(SCN)2]22- by interactions with the counterion. Weak bonding interactions and luminescent transitions were explained by calculation of Hg dimers, excimers and exciplexes formed with noble gases.

Baeyer-Villiger oxidation of 1,9-dibromopentacyclo[5.4.0.02,6.03,10.05,9]undecane-8,11-dione (1,9-dibromo-PCU-8,11-dione) was performed by using an excess amount of m-chloroperbenzoic acid (3 equivalents) and resulted in the formation of the corresponding monolactone. The reaction would not proceed to the dilactone stage. The structure of the reaction product was established unequivocally via single crystal X-ray diffraction. Baeyer-Villiger oxidation of 1,9-dibromo-PCU-8,11-dione using ceric ammonium nitrate (CAN) was also performed and afforded a mixture of lactones. Only one of these lactones, which also contained an alkene functionality, could be isolated and characterized. 1,7-dibromo-PCU-8,11-dione was also reacted with CAN, yielding the mono-lactone, which has also been characterized.

Baeyer-Villiger oxidation of 1-methylpentacyclo[5.4.0.02,6.03,10.05,9] undecane-8,11-dione, performed by using m-chloroperbenzoic acid in 1:1 molar ratio, resulted in the formation of monolactone. The corresponding dilactone, was synthesized by reacting 1-methyl-PCU-8,11-dione with m-chloroperbenzoic acid in 1:2 molar ratio. 6-Methyl-1,4,4a,8a-tetrahydro-1,4-methanonaphthalene-5,8-dione was converted into the corresponding exo-6,7-monoepoxide via treatment with 30% aqueous hydrogen peroxide. Epoxidation of this monoepoxide by using m-chloroperbenzoic acid afforded the corresponding bis-epoxide. Ceric ammonium nitrate (CAN) promoted oxidation of 1-methyl-PCU-8,11-dione afforded "methylated lactones" and a "methylated alkene."

Three different types of cage crown ethers have been prepared and their complexation properties with Ag(I) have been studied. Atomic absorption, fluorescence quenching, and UV absorption have been used to study the interaction between the hosts (cage crown ethers) and guests (Ag+). For the cage-annulated crown ethers that contain aromatic rings, cation-π and π-π interactions may contribute significantly to the overall complexation ability of the host system. Piperazine groups may cooperate, and the piperazine nitrogen atoms provide unshared electrons, which may form a complex with Ag+. In addition, relatively soft donor atoms (e.g., Br) are well-suited for complexation with Ag+, which is a softer Lewis acid than alkali metal cations.

The kinetics of the pressure dependent O + SO2 + Ar reaction have been investigated using laser photolysis resonance fluorescence at temperatures of 289 K, 399 K, 581 K, 699 K, 842 K and 1040 K and at pressures from 30-665 torr. Falloff was observed for the first time in the pressure dependence. Application of Lindemann theory yielded an Arrhenius expression of k(T) = 3.3 x 10-32exp(-992/T) cm6 molecule-1 s-1 for the low pressure limit and k(T) = 8.47 x 10-14exp(-468/T) cm3 molecule-1 s-1 for the high pressure limit at temperatures between 289 and 842 K. The reaction is unusual as it possesses a positive activation energy at low temperature, yet at higher temperatures the activation energy is negative, illustrating a reaction barrier.

Nanocrystalline praseodymium oxide films have been successfully generated on stainless steel substrates. The electrochemical deposition was performed in the cathode compartment of a divided electrochemical cell with a regular three-electrode configuration. The green films obtained by electrodeposition were then annealed at high temperatures for 1-3 hours. X-ray diffraction revealed the fluorite structure of Pr6O11 and the crystallite size was calculated. X-ray photoelectron spectroscopy was employed to study the composition of the oxide films and also the oxidation state of Pr. Scanning electron microscopy was utilized to study the surface texture and microstructure of deposits. Fourier transform infrared spectrometery was used to investigate the composition of the films. The effects of different conditions on the green films were also studied such as different pH values of the electrolyte solution, different deposition modes, different supporting electrolytes and different applied current densities. Sintering experiments were conducted to investigate the properties of the green films. Praseodymium oxide powders were also successfully prepared by combining electrochemical methods with sintering processes. The praseodymium oxide powders were characterized by X-ray diffraction and Fourier transform infrared spectroscopy. The crystallite sizes of the powders were evaluated.

A variety of optically active macrocyclic crown ethers that serve as "host" systems that are capable of differentiating between enantiomeric "guest" molecules during host-guest complexation have been prepared via incorporation of chiral elements into the crown ring skeleton. The ability of these crown ethers to recognize the enantiomers of guest salts, i.e., (+) a-methyl benzylamine and to transport them enantioselectively in W-tube transport experiments were studied. The ability of these crown ethers to perform as chiral catalysts in an enantioselective Michael addition was studied. The extent of asymmetric induction, expressed in terms of the enantiomeric excess (%ee), was monitored by measuring the optical rotation of the product and comparing to the literature value.

Semiconductor circuitry feature miniaturization continues in response to Moore 's Law pushing the limits of aluminum and forcing the transition to Cu due to its lower resistivity and electromigration. Copper diffuses into silicon dioxide under thermal and electrical stresses, requiring the use of barriers to inhibit diffusion, adding to the insulator thickness and delay time, or replacement of SiO2 with new insulator materials that can inhibit diffusion while enabling Cu wetting. This study proposes modified amorphous silicon carbon hydrogen (a-Si:C:H) films as possible diffusion barriers and replacements for SiO2 between metal levels, interlevel dielectric (ILD), or between metal lines (IMD), based upon the diffusion inhibition of previous a-Si:C:H species expected lower dielectric constants, acceptable thermal conductivity. Vinyltrimethylsilane (VTMS) precursor was condensed on a titanium substrate at 90 K and bombarded with electron beams to induce crosslinking and form polymerized a-Si:C:H films. Modifications of the films with hydroxyl and nitrogen was accomplished by dosing the condensed VTMS with water or ammonia before electron bombardment producing a-Si:C:H/OH and a-Si:C:H/N and a-Si:C:H/OH/N polymerized films in expectation of developing films that would inhibit copper diffusion and promote Cu adherence, wetting, on the film surface. X-ray Photoelectron Spectroscopy was used to characterize Cu metallization of …

The square-planar tetracyanonickelate(II) anion was intercalated into 2:1 and 3:1 Mg-Al layered double hydroxide systems (LDHs). In the 2:1 material, the anion holds itself at an angle of about 30° to the layers, whereas in the 3:1 material it lies more or less parallel to the layers. This is confirmed by orientation effects in the infrared spectra of the intercalated materials and by X-ray diffraction (XRD) data. The measured basal spacings for the intercalated LDH hosts are approximately 11 Å for the 2:1 and approximately 8 Å for the 3:1. The IR of the 2:1 material shows a slight splitting in the ν(CN) peak, which is suppressed in that compound's oriented IR spectrum, indicating that at least some of the intercalated anion's polarization is along the z-axis. This effect is not seen in the 3:1 material. A comparison between chloride LDHs and nitrate LDHs was made with respect to intercalation of tetracyanonickelate(II) anions. Both XRD data and atomic absorption spectroscopy (AAS) data of the LDH tetracyanonickelates confirms that there are no significant differences between the products from the two types of starting materials. The presence of a weak ν(NO) peak in the IR spectra of those samples made from nitrate …

Various gold complexes were computationally investigated, to probe their photophysical, geometric, and bonding properties. The geometry of AuI complexes (ground state singlet) is very sensitive to the electronic nature of the ligands: σ-donors gave a two-coordinate, linear shape; however, σ-acceptors yielded a three-coordinate, trigonal planar geometry. Doublet AuIIL3 complexes distort to T-shape, and are thus ground state models of the corresponding triplet AuIL3. The disproportionation of AuIIL3 to AuIL3 and AuIIIL3 is endothermic for all ligands investigated, however, σ-donors are better experimental targets for AuII complexes. For dimeric AuI complexes, only one gold center in the optimized triplet exciton displays a Jahn-Teller distortion, and the Au---Au distance is reduced versus the ground state distance (i.e., two reasons for large Stokes' shifts).

An NMR spectroscopy study of trimethylsilylmethyllilthium, TMSM-Li, indicates that TMSM-Li exists as two different aggregates in cyclopentane solution. Using previously reported colligative properties of TMSM-Li in different solutions in connection with new 13C and 6Li NMR data collected in this study, aggregation states were assigned as octamer and hexamer. Low temperature 13C and 6Li NMR peak intensities indicated an equilibrium exists between the two aggregates that shifts toward the octamer as the temperature decreases. ΔH was calculated to be 5.23 + 0.15 kcal/mol and ΔS was calculated to be 17.9 + 0.6 eu for the hexamer/octamer equilibrium system. Samples of TMSM-Li were mixed with TMSM-OH in attempts to form mixed alkyllithium/lithium alkoxide aggregates. 13C NMR data for these mixtures gave inconclusive results whether or not these compounds formed, which is different from other primary alkyllithium compounds studied in the past. A study of neopentyllithium, NpLi, indicates only one aggregate in solution with the aggregation state unknown using low temperature 13C NMR spectroscopy.

Electrodeposition is a novel method for fabrication of diamond-like carbon (DLC) films on metal substrates. In this work, DLC was electrochemically deposited on different substrates based on an anodic oxidation cyclization of acetylene in liquid ammonia. Successfully anodic deposition was carried out for DLC onto nickel substrate at temperatures below -40°C. Comparative studies were performed on a series of different carbon sources (acetylene, sodium acetylide, and a mixture of acetylene and sodium acetylide). The films were characterized using a variety of methods including Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), XPS valence band spectra, and/or scanning electron microscopy (SEM). Raman spectroscopy is used as a bench mark technique to verify the presence of deposited DLC films, to access the films homogeneities, and to provide the ratio of the different carbon phases, mainly disordered graphite (D) and graphite (G) phases in the films. A combination of the Raman with FTIR and valence band spectra analysis allowed the distinction between hydrogenated DLC and unhydrogenated DLC films. Three different kinds of DLC [(1) hydrogenated DLC (a-C:H); (2) tetrahedral hydrogenated DLC (ta-C:H); and (3) graphitic-like DLC] were deposited depending upon the deposition conditions and substrates. Temperature and current density are …