Reductive nitrosylation and complexation of ammonium pertechnetate by acetohydroxamic acid has been achieved in aqueous nitric and perchloric acid solutions. The kinetics of the reaction depend on the relative concentrations of the reaction components and are accelerated at higher temperatures. The reaction does not occur unless conditions are acidic. Analysis of the x-ray absorption fine structure spectroscopic data is consistent with a pseudo-octahedral geometry with the linear Tc-N-O bond typical of technetium nitrosyl compounds, and electron spin resonance spectroscopy is consistent with a the d{sup 5} Tc(II) nitrosyl complex. The nitrosyl source is generally AHA, but may be augmented by products of reaction with nitric acid. The resulting low-valency trans-aquonitrosyl(diacetohydroxamic)-technetium(II) complex (1) is highly soluble in water, extremely hydrophilic, and is not extracted by tri-n-butylphosphate in a dodecane diluent. Its extraction properties are not pH-dependent; titration studies indicate a single species from pH 4.5 down to -0.6 (calculated). This molecule is resistant to oxidation by H{sub 2}O{sub 2}, even at high pH, and can undergo substitution to form other technetium nitrosyl complexes. The formation of 1 may strongly impact the fate of technetium in the nuclear fuel cycle.

The authors compare frequency doubling of broadband light in a single nonlinear crystal with doubling in five crystals with intercrystal temporal walk off compensation, and with doubling in five crystals adjusted for offset phase matching frequencies. Using a plane-wave, dispersive numerical model of frequency doubling they study the bandwidth of the second harmonic and the conversion efficiency as functions of crystal length and fundamental irradiance. For low irradiance the offset phase matching arrangement has lower efficiency than a single crystal of the same total length but gives a broader second harmonic bandwidth. The walk off compensated arrangement gives both higher conversion efficiency and broader bandwidth than a single crystal. At high irradiance, both multicrystal arrangements improve on the single crystal efficiency while maintaining broad bandwidth.

In this paper the authors describe the approach to research, develop, and evaluate prototype middleware tools and architectures. The developed tools can be used by scientists to compose astronomical data analysis pipelines easily. They use the SuperMacho data pipelines as example applications to test the framework. they describe their experience from scheduling and running these analysis pipelines on massive parallel processing machines. they use MCR a Linux cluster machine with 1152 nodes and Luster parallel file system as the hardware test-bed to test and enhance the scalability of the tools.

In this paper we describe our approach to build a pipeline simulator for the future Large-scale Synoptic Survey Telescope (LSST). The simulated pipeline will be used to research and evaluate software architectures that are efficient and flexible. It will also be used to define the real-time software and hardware requirements needed to support the anticipated LSST data rates. The LSST data pipeline requirements are still being defined, however, previous surveys can provide a good source for data requirements. Our approach is to use the SuperMacho data pipeline as a prototyping tool to identify a framework for building Modular Data-Centric Pipeline (MDCP) architectures. The prototyping is done in a hierarchical fashion to help capture and define the general data attributes (schema) first. We then model other necessary components based on science and performance requirements. We use identified schemas or data attributes as a way to define a data model for LSST.

Viscosities of water, nitrogen and carbon dioxide have been measured at elevated pressures and temperatures in the diamond-anvil cell. A strong correlation between viscosity and entropy has been confirmed.

The radiation-damaged polystyrene (given the identification name of 'polycube') was fabricated by mixing high-density polystyrene material ("Dylene Fines # 100") with plutonium and uranium oxides. The polycubes were used in the 1960s for criticality studies during processing of spent nuclear fuel. The polycubes have since been stored for almost 40 years at the Hanford Plutonium Finishing Plant (PFP) after failure of two processes to reclaim the plutonium and uranium oxides from the polystyrene matrix. Thermal decomposition products from this highly cross-linked polystyrene matrix were characterized using Gas Chromatograph/Mass Spectroscopy (GC/MS) system coupled to a horizontal furnace. The decomposition studies were performed in air and helium atmospheres at about 773 K. The volatile and semi-volatile organic products for the radiation-damaged polystyrene were different compared to virgin polystyrene. The differences were in the number of organic species generated and their concentrations. In the inert (i.e., helium) atmosphere, the major volatile organic products identified (in order of decreasing concentrations) were styrene, benzene, toluene, ethylbenzene, xylene, nathphalene, propane, .alpha.-methylbenzene, indene and 1,2,3-trimethylbenzene. But in air, the major volatile organic species identified changed slightly. Concentrations of the organic species in the inert atmosphere were significantly higher than those for the air atmosphere processing. Overall, 38 …

The overall objective of this project is the three phase development of an Early Entrance Coproduction Plant (EECP) which produces at least one product from at least two of the following three categories: (1) electric power (or heat), (2) fuels, and (3) chemicals. The objective is to have these products produced by technologies capable of using synthesis gas derived from coal and/or other carbonaceous feedstock. The objective of Phase I is to determine the feasibility and define the concept for the EECP located at a specific site and to develop a Research, Development, and Testing Plan (RD and T) for implementation in Phase II. The objective of Phase II is to implement the RD and T as outlined in the Phase I RD and T Plan to enhance the development and commercial acceptance of coproduction technology that produces high-value products, particularly those that are critical to our domestic fuel and power requirements. The project will resolve critical knowledge and technology gaps on the integration of gasification and downstream processing to coproduce some combination of power, fuels, and chemicals from coal and other feedstocks. The objective of Phase III is to develop an engineering design package and a financing plan for …

Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen (LH{sub 2}) or ambient-temperature compressed hydrogen (CH{sub 2}). Insulated pressure vessels offer the advantages of liquid hydrogen tanks (low weight and volume), with reduced disadvantages (fuel flexibility, lower energy requirement for hydrogen liquefaction and reduced evaporative losses). The work described here is directed at verifying that commercially available pressure vessels can be safely used to store liquid hydrogen. The use of commercially available pressure vessels significantly reduces the cost and complexity of the insulated pressure vessel development effort. This paper describes a series of tests that have been done with aluminum-lined, fiber-wrapped vessels to evaluate the damage caused by low temperature operation. All analysis and experiments to date indicate that no significant damage has resulted. Required future tests are described that will prove that no technical barriers exist to the safe use of aluminum-fiber vessels at cryogenic temperatures. Future activities also include a demonstration project in which the insulated pressure vessels will be installed and tested on two vehicles. A draft standard will also be generated for obtaining certification for insulated pressure vessels.

This report provides results from an ongoing project to monitor the migration behavior and survival of wild juvenile spring/summer Chinook salmon in the Snake River Basin. Data reported is from detections of PIT tagged fish during late summer 2007 through mid-2008. Fish were tagged in summer 2007 by the National Marine Fisheries Service (NMFS) in Idaho and by the Oregon Department of Fish and Wildlife (ODFW) in Oregon. Our analyses include migration behavior and estimated survival of fish at instream PIT-tag monitors and arrival timing and estimated survival to Lower Granite Dam. Principal results from tagging and interrogation during 2007-2008 are listed below: (1) In July and August 2007, we PIT tagged and released 7,390 wild Chinook salmon parr in 12 Idaho streams or sample areas. (2) Overall observed mortality from collection, handling, tagging, and after a 24-hour holding period was 1.4%. (3) Of the 2,524 Chinook salmon parr PIT tagged and released in Valley Creek in summer 2007, 218 (8.6%) were detected at two instream PIT-tag monitoring systems in lower Valley Creek from late summer 2007 to the following spring 2008. Of these, 71.6% were detected in late summer/fall, 11.9% in winter, and 16.5% in spring. Estimated parr-to-smolt survival …

This study examined waste feed and solvent limits for the Modular Caustic-Side Solvent Extraction Unit (MCU) currently being designed and built at the Savannah River Site (SRS) to remove cesium from highly alkaline radioactive waste. The study involved proposing ranges for 12 waste feed components (i.e., Na{sup +}, K{sup +}, Cs{sup +}, OH{sup -}, NO{sub 3}{sup -}, NO{sub 2}{sup -}, Cl{sup -}, F{sup -}, SO{sub 4}{sup 2-}, PO{sub 4}{sup 3-}, and CO{sub 3}{sup 2-}, and AlO{sub 2}{sup -}) through a compilation of SRS waste data. Statistical design methods were used to generate numerous wastes with varying compositions from the proposed ranges. An Oak Ridge National Laboratory (ORNL) model called SXFIT was used to predict the cesium extraction distribution coefficients (D-values) between the organic (solvent) phase and the aqueous waste phase using the waste component concentrations as inputs. The D-values from the SXFIT model were used as input along with MCU base case process parameters to a SASSE (Spreadsheet Algorithm for Stagewise Solvent Extraction) model to calculate final cesium concentrations for the MCU. The SASSE model was developed at Argonne National Laboratory (ANL). The SXFIT D-value and the waste component concentration data were used to develop a handier alternative model (neural …

The recently discovered dynamical diffraction effect ''neutron camel'' was used for the residual stress measurements in a thick Si(111) crystal coated with a 2000 {angstrom} thick Ni film. The observed asymmetry of the back-face rocking curve corresponds to the bending radius of {approx} 19 km and the tension force applied to the Ni film is {approx} 90 N/m. Relative deformation of the Si crystallographic cells in the vicinity of diffractive surfaces is |{partial_derivative}u{sub z}/{partial_derivative}z| {approx} 1.6 x 10{sup -6}.

The U.S. Department of Energy (DOE) is faced with a massive cleanup task in resolving the legacy of environmental problems from years of manufacturing nuclear weapons. One of the major activities within this task is the treatment and disposal of the extremely large amount of high-level radioactive (HLW) waste stored at the Hanford Site in Richland, Washington. The current planning for the method of choice for accomplishing this task is to vitrify (glassify) this waste for disposal in a geologic repository. This paper describes the results of the DOE-chartered independent review of alternatives for solidification of Hanford HLW that could achieve major cost reductions with reasonable long-term risks, including recommendations on a path forward for advanced melter and waste form material research and development. The potential for improved cost performance was considered to depend largely on increased waste loading (fewer high-level waste canisters for disposal), higher throughput, or decreased vitrification facility size.

The overall objective of this project is the three phase development of an Early Entrance Coproduction Plant (EECP) which uses petroleum coke to produce at least one product from at least two of the following three categories: (1) electric power (or heat), (2) fuels, and (3) chemicals. The objective is to have these products produced by technologies capable of using synthesis gas derived from coal and/or other carbonaceous feedstocks. The objectives of Phase I were to determine the feasibility and define the concept for the EECP located at a specific site; develop a Research, Development, and Testing (RD&T) Plan for implementation in Phase II; and prepare a Preliminary Project Financing Plan. The objective of Phase II is to implement the work as outlined in the Phase I RD&T Plan to enhance the development and commercial acceptance of coproduction technology that produces high-value products, particularly those that are critical to our domestic fuel and power requirements. The work performed under Phase II will resolve critical knowledge and technology gaps on the integration of gasification and downstream processing to coproduce some combination of power, fuels, and chemicals from coal and/or other carbonaceous feedstocks. The objective of Phase III is to develop an …

In the framework of the preparation for the decommissioning of the Chernobyl Nuclear Power Plant (ChNPP) an Industrial Complex for Solid Radwaste Management (ICSRM) will be built under the EC TACIS Program in the vicinity of ChNPP. The paper will present the proposed concepts and their integration into existing buildings and installations. Further, the paper will consider the safety cases, as well as the integration of Western and Ukrainian Organizations into a cohesive project team and the requirement to guarantee the fulfillment of both Western standards and Ukrainian regulations and licensing requirements. The paper will provide information on the status of the interim design and the effects of value engineering on the output of basic design phase. The paper therefor summarizes the design results of the involved design engineers of the Design and Process Providers BNFL (LOT 1), RWE NUKEM GmbH (LOT 2 and General) and INITEC (LOT 3).

The effect of heat-island reduction (HIR) strategies on annual energy savings and peak-power avoidance of the building sector of the Greater Toronto Area is calculated, using an hourly building energy simulation model. Results show that ratepayers could realize potential annual energy savings of over $11M from the effects of HIR strategies. The residential sector accounts for over half (59%) of the total savings, offices 13% and retail stores 28%. Savings from cool roofs are about 20%, shade trees 30%, wind shielding of trees 37%, and ambient cooling by trees and reflective surfaces 12%. These results are preliminary and highly sensitive to the relative price of gas and electricity. Potential annual electricity savings are estimated at about 150GWh and potential peak-power avoidance at 250MW.

None

The growth of the livestock industry provides a valuable source of affordable, sustainable, and renewable bioenergy, while also requiring the safe disposal of the large quantities of animal wastes (manure) generated at dairy, swine, and poultry farms. If these biomass resources are mishandled and underutilized, major environmental problems will be created, such as surface and ground water contamination, odors, dust, ammonia leaching, and methane emission. Anaerobic digestion of animal wastes, in which microorganisms break down organic materials in the absence of oxygen, is one of the most promising waste treatment technologies. This process produces biogas typically containing {approx}65% methane and {approx}35% carbon dioxide. The production of biogas through anaerobic digestion from animal wastes, landfills, and municipal waste water treatment plants represents a large source of renewable and sustainable bio-fuel. Such bio-fuel can be combusted directly, used in internal combustion engines, converted into methanol, or partially oxidized to produce synthesis gas (a mixture of hydrogen and carbon monoxide) that can be converted to clean liquid fuels and chemicals via Fischer-Tropsch synthesis. Different design and mixing configurations of anaerobic digesters for treating cow manure have been utilized commercially and/or tested on a laboratory scale. These digesters include mechanically mixed, gas recirculation mixed, …

We are investigating the evaporation of pore water representative of the designated high-level-nuclear-waste repository at Yucca Mountain, NV to predict the range of brine compositions that may contact waste containers. These brines could form potentially corrosive thin films on the containers and impact their long-term integrity. Here we report the geochemistry of a relatively complex synthetic Topopah Spring Tuff pore water that was progressively evaporated in a series of experiments. The experiments were conducted in a closed vessel, heated to 95 C, and purged with atmospheric CO{sub 2}. Aqueous samples of the evaporating solution were taken and analyzed to determine the evolving water chemistry, and the final solid precipitate was analyzed by X-ray diffraction. The synthetic Topopah Spring Tuff water evolved towards a complex brine that contains about 3 mol% SO{sub 4}, and 2 mol% Ca, 3 mol% K, 5 mol% NO{sub 3}, 40 mol% Cl, and 47 mol% Na. Trends in the solution data and identification of CaSO{sub 4} solids (anhydrite and bassanite) suggest that fluorite, carbonate, sulfate, and Mg-silicate precipitation minimize the corrosion potential of ''sulfate type pore water'' by removing F, Ca, and Mg during the early stages of evaporation.

An overview is given of the experimental neutrino mixing results and types of neutrino models proposed, with special attention to the general features of various GUT models involving intra-family symmetries and horizontal flavor symmetries. Many of the features are then illustrated by a specific SO (10) SUSY GUT model formulated by S.M. Barr and the author which can explain all four types of solar neutrino mixing solutions by various choices of the right-handed Majorana mass matrix. The quantitative nature of the model's large mixing angle solution is used to compare the reaches of a neutrino super beam and a neutrino factory for determining the small U{sub e3} mixing matrix element.

Evaluating the chemical background in the GC/MS system (system background) and solvent purity. This procedure will allow the analyst to verify that the GC/MS is free of chemical interferences or contamination and verify the solvent being utilized is free of interferences - Conduct a GC/MS analysis without injecting a solvent (system background) and Conduct a GC/MS analysis inject 1uL of CH2Cl2 solvent (Solvent background). GC conditions: (1) Injector Temperature (C): Injector Temperature is typically set at 250; (2) Transferline Temperature (C) - The Transferline Temperature is typically set at 280 C; (3) Constant flow (Sec./cm2) - This value, in seconds per cubic cm. Typically, set at 32; (4) Splitless mode (Sec.) - This value, in seconds, is the time before the purge valve opens. Typically, set at 45 seconds; (5) Starting Temperature (C): The Starting Temperature value can be set at 40 C; (6) Hold Time 1 (Min.) - Hold Time 1 is the amount of time, in minutes at the Starting Temperature that Ramp 1 Temperature is held. Typically set at 3 minutes; (7) Ramp 1 Rate (C/Min.) - Ramp 1 Rate is the temperature rise per unit time and has a typically value of 8 C per minute …

This procedure requires the binder and uncoated RDX be prepared in separate steps, see Figure 1: (1) The binder and dye are mixed by agitation with a water-insoluble organic solvent (e.g., toluene), I; (2) The RDX/PETN is agitated thoroughly with water, II; (3) The binder solution I is added to the RDX/water mixture at II with thorough mixing to form a slurry III; (4) In the next step the solvent is distilled off at IV leaving resulting granules; (5) The next step is followed by filtration at V, which may be done by vacuum; (6) The composition is then dried at VI to a dough-like consistency.

None

In May of 2002, the River Protection Project at Hanford proposed as part of the accelerated cleanup for the entire Hanford Site to ''accelerate waste stabilization by developing and deploying alternative treatment and immobilization solutions that are aligned with the waste characteristics to add assurance that overall waste treatment/immobilization will be completed 20 or more years sooner.'' This paper addresses one of these elements: development of recommendations for the supplemental technologies that have the greatest potential to supplement the River Protection Project's new Waste Treatment Plant throughput and achieve completion of waste processing by 2028. Low-activity waste treatment in the Waste Treatment Plant needs either to be enhanced or supplemented to enable the full amount of low-activity feed in the single-shell and double-shell tanks to be processed by 2028. The supplemental technologies are considered for low-activity waste feed that represents the maximum effectiveness of treatment compared with Waste Treatment Plant processing. During the Spring of 2002, over two dozen candidate technologies were assessed by staff from the U.S Department of Energy (DOE) Headquarters, Hanford Office of River Protection, representatives from the Washington State Department of Ecology and Region 10 of the Environmental Protection Agency, staff from many national laboratories, as …

The Motional Stark Effect (MSE) diagnostic on ITER determines the local plasma current density by measuring the polarization angle of light resulting from the interaction of a high energy neutral heating beam and the tokamak plasma. This light signal has to be transmitted from the edge and core of the plasma to a polarization analyzer located in the port plug. The optical system should either preserve the polarization information, or it should be possible to reliably calibrate any changes induced by the optics. This LLNL Work for Others project for the US ITER Project Office (USIPO) is focused on the design of the viewing optics for both the edge and core MSE systems. Several design constraints were considered, including: image quality, lack of polarization aberrations, ease of construction and cost of mirrors, neutron shielding, and geometric layout in the equatorial port plugs. The edge MSE optics are located in ITER equatorial port 3 and view Heating Beam 5, and the core system is located in equatorial port 1 viewing heating beam 4. The current work is an extension of previous preliminary design work completed by the ITER central team (ITER resources were not available to complete a detailed optimization of …