The radiation-damaged polystyrene (given the identification name of 'polycube') was fabricated by mixing high-density polystyrene material ("Dylene Fines # 100") with plutonium and uranium oxides. The polycubes were used in the 1960s for criticality studies during processing of spent nuclear fuel. The polycubes have since been stored for almost 40 years at the Hanford Plutonium Finishing Plant (PFP) after failure of two processes to reclaim the plutonium and uranium oxides from the polystyrene matrix. Thermal decomposition products from this highly cross-linked polystyrene matrix were characterized using Gas Chromatograph/Mass Spectroscopy (GC/MS) system coupled to a horizontal furnace. The decomposition studies were performed in air and helium atmospheres at about 773 K. The volatile and semi-volatile organic products for the radiation-damaged polystyrene were different compared to virgin polystyrene. The differences were in the number of organic species generated and their concentrations. In the inert (i.e., helium) atmosphere, the major volatile organic products identified (in order of decreasing concentrations) were styrene, benzene, toluene, ethylbenzene, xylene, nathphalene, propane, .alpha.-methylbenzene, indene and 1,2,3-trimethylbenzene. But in air, the major volatile organic species identified changed slightly. Concentrations of the organic species in the inert atmosphere were significantly higher than those for the air atmosphere processing. Overall, 38 …

The overall objective of this project is the three phase development of an Early Entrance Coproduction Plant (EECP) which produces at least one product from at least two of the following three categories: (1) electric power (or heat), (2) fuels, and (3) chemicals. The objective is to have these products produced by technologies capable of using synthesis gas derived from coal and/or other carbonaceous feedstock. The objective of Phase I is to determine the feasibility and define the concept for the EECP located at a specific site and to develop a Research, Development, and Testing Plan (RD and T) for implementation in Phase II. The objective of Phase II is to implement the RD and T as outlined in the Phase I RD and T Plan to enhance the development and commercial acceptance of coproduction technology that produces high-value products, particularly those that are critical to our domestic fuel and power requirements. The project will resolve critical knowledge and technology gaps on the integration of gasification and downstream processing to coproduce some combination of power, fuels, and chemicals from coal and other feedstocks. The objective of Phase III is to develop an engineering design package and a financing plan for …

Marine sediment remediation at the United Heckathorn Superfund Site was completed in April 1997. Water and mussel tissues were sampled in February 1999 from four stations near Lauritzen Canal in Richmond, California, for Year 2 of post-remediation monitoring of marine areas near the United Heckathorn Site. Dieldrin and dichlorodiphenyl trichloroethane (DDT) were analyzed in water samples, tissue samples from resident mussels, and tissue samples from transplanted mussels deployed for 4 months. Concentrations of dieldrin and total DDT in water and total DDT in tissue were compared with Year 1 of post-remediation monitoring, and with preremediation data from the California State Mussel Watch program (tissues) and the Ecological Risk Assessment for the United Heckathorn Superfund Site (tissues and water). Mussel tissues were also analyzed for polychlorinated biphenyls (PCB), which were detected in sediment samples. Chlorinated pesticide concentrations in water samples were similar to preremediation levels and did not meet remediation goals. Mean dieidrin concentrations in water ranged from 0.62 rig/L to 12.5 ng/L and were higher than the remediation goal (0.14 ng/L) at all stations. Mean total DDT concentrations in water ranged from 14.4 ng/L to 62.3 ng/L and exceeded the remediation goal (0.59 ng/L) at all stations. The highest concentrations …

Post-Remediation Biomonitoring of Pesticides and Other Contaminants in Marine Waters and Sediment Near the United Heckathorn Superfund Site, Richmond, California

None

Controlled landfilling is an approach to manage solid waste landfills, so as to rapidly complete methane generation, while maximizing gas capture and minimizing the usual emissions of methane to the atmosphere. With controlled landfilling, methane generation is accelerated to more rapid and earlier completion to full potential by improving conditions (principally moisture, but also temperature) to optimize biological processes occurring within the landfill. Gas is contained through use of surface membrane cover. Gas is captured via porous layers, under the cover, operated at slight vacuum. A field demonstration project has been ongoing under NETL sponsorship for the past several years near Davis, CA. Results have been extremely encouraging. Two major benefits of the technology are reduction of landfill methane emissions to minuscule levels, and the recovery of greater amounts of landfill methane energy in much shorter times, more predictably, than with conventional landfill practice. With the large amount of US landfill methane generated, and greenhouse potency of methane, better landfill methane control can play a substantial role both in reduction of US greenhouse gas emissions and in US renewable energy. The work described in this report, to demonstrate and advance this technology, has used two demonstration-scale cells of size (8000 …

This document specifies the critical characteristics for containers procured for Plutonium Finishing Plant's (PFP's) Vault Operations system as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to perform its safety function.

In the transient diffraction NLYF proposal we set forward a program of work to investigate the response of crystals to shock compression in regions of strain rates previously unexplored, in a coordinated experimental, computational, and analytical program. Time resolved x-ray diffraction was used to directly determine the lattice parameters of crystals during shock loading previously on the Nova and Trident laser facilities. Under this proposal we extended this work to exploit the multi-beam direct drive capability of the Omega laser facility to allow more extensive diagnostic access for measuring the lattice parameters both parallel and perpendicular to the shock front. Under the NLUF Program in FY 99, we transitioned the dynamic diffraction experiments to the OMEGA facility. We developed a direct drive target configuration that uses a single beam to direct irradiate the surface of a thin crystal and 4 beams to irradiate a separate metal backlighter foil. Experiments were done with single crystal Si to demonstrate that the target design worked and that simultaneous measurements of compression both parallel and perpendicular to the shock propagation direction could be performed. We obtained simultaneous measurements of the (400) and (040) lattice planes during the period when a shock traveled through the …

None

Only two intrinsic approaches to increasing the density of energy stored in capacitors are known: (1) Increase the Dielectric Constant while maintaining the breakdown filed; and (2) Increase the breakdown field for a given dielectric constant material. The maximum energy density, E{sub 0} (Joules/cm{sup 3}) that can be stored in the dielectric of a capacitor is given by: E{sub 0} = 1/2 k {var_epsilon}{sub 0} V{sub b}{sup 2} (Joules/cm{sup 3} dielectric). Where k is the relative permittivity (dielectric constant), {var_epsilon}{sub 0} is the permittivity of free space (8.894 x 10{sup -14} F/cm) and V{sub b} the dielectric material breakdown field. In this project we have successfully developed capacitor structures using dielectric materials with 3 < k < 50 that exhibit high breakdown fields. The observed performance of these capacitors as characterized by the energy stored per unit volume of dielectric at V{sub b} are compared on the basis of the breakdown field in Figure 1.

The Hanford Site 200 Area Effluent Treatment Facility (ETF) processes contaminated liquids derived from Hanford Site facilities. Groundwater monitoring for tritium and other constituents is required by the state-issued permit at 22 wells surrounding the facility. Water level measurements in nearby wells indicate that a small hydraulic mound exists around the SALDS facility as a result of discharges. Evaluation of this condition indicates that the network is currently adequate for tracking potential effects of the SALDS on the groundwater. During FY 2000, average tritium activities in most wells declined from average activities in 1999. The exception was deep well 699-48-77C, where tritium results were at an all-time high (710,000 pCi/L) as a result of the delayed penetration of effluent deeper into the aquifer. Of the 12 constituents with permit enforcement limits, which are monitored in SALDS proximal wells, all were within groundwater limitations during FY 2000. Analyses for conductivity, total dissolved solids, sulfate, chloride, sulfate, dissolved calcium, and dissolved sodium indicate that well 699-48-77A and, to a lesser extent, well 699-48-77D show the effects of dilute effluent entering groundwater, resulting in a depression of concentrations of these constituents below natural background levels. Recommendations for future monitoring include temporarily increasing the …

The Hanford Site 200 Area Effluent Treatment Facility (ETF) processes contaminated liquids derived from Hanford Site facilities. The clean water generated by these processes is occasionally enriched in tritium, and is discharged to the 200 Area State Approved Land Disposal Site (SALDS). Groundwater monitoring for tritium and other constituents is required by the state-issued permit at 22 wells surrounding the facility. Water level measurements in nearby wells indicate that a small hydraulic mound exists around the SALDS facility as a result of discharges. This feature is directing groundwater flow radially outward a short distance before the regional northeasterly flow predominates. Evaluation of this condition indicates that the networks currently adequate for tracking potential effects of the SALDS on the groundwater. During FY 2000, average tritium activities inmost wells declined from average activities in 1999. The exceptions are deep well 699-48-77C, where tritium results reached a maximum value of 710,000 pCi/L as a result of the delayed penetration of effluent deeper into the aquifer, and in well 299-W7-3, along the northern boundary of the 200 West Area, which has apparently been affected for the first time by the SALDS tritium plume, with a tritium activity of 1,400 pCi/L measured in August …

This document was prepared to support the primary goals of the Department of Energy, Office of Heavy Vehicle Technologies. These were recently stated as follows: ''Develop by 2004 the enabling technologies for a class 7-8 truck with a fuel efficiency of 10 mpg (at 65 mph) which will meet prevailing emission standards. For Class 3-6 trucks operating on an urban driving cycle, develop by 2004 commercially viable vehicles that achieve at least double the fuel economy of comparable current vehicles (1999), and as a research goal, reduce criteria pollutants to 30% below EPA standards. Develop by 2004 the diesel engine enabling technologies to support large-scale industry dieselization of Class 1 and 2 trucks, achieving a 35 % fuel efficiency improvement over comparable gasoline-fueled trucks, while meeting applicable emissions standards.'' The enabling technologies for improving the fuel efficiency of trucks, include not only engine technologies but also technologies involved with lowering the rolling resistance of tires, reducing vehicle aerodynamic drag, improving thermal management, and reducing parasitic frictional losses in drive train components. Opportunities also exist for making better use of the energy that might ordinarily be dissipated during vehicle braking. Braking systems must be included in this evaluation since safety in …

The purpose of this study is to determine, as functions of total copper loading and iron REDOX in glass, any dependence of the leaching behavior of borosilicate glass on metallic copper.

This revision was prepared to address comments from DOE-SR that arose following publication of revision 0. This Special Analysis (SA) addresses disposal of wastes with high concentrations of I-129 in the Intermediate-Level (IL) Vaults at the operating, low-level radioactive waste disposal facility (the E-Area Low-Level Waste Facility or LLWF) on the Savannah River Site (SRS). This SA provides limits for disposal in the IL Vaults of high-concentration I-129 wastes, including activated carbon beds from the Effluent Treatment Facility (ETF), based on their measured, waste-specific Kds.

None

None

Sluicing operations were performed to retrieve high-heat sludge from single-shell tank 241-C-106 and transfer it to double-shell tank 241-AY-102 using the Waste Retrieval Sluicing System. This eliminated the high-heat safety issue for C-106 and demonstrated a technology for retrieval of single-shell tank waste. Both AY-102 and C-106 were monitored during the waste transfer operations, providing a clear picture of general trends in each tank. Specific issues addressed were evaluation of the data for evidence of flammable gas accumulation in AY-102 and thermal performance of AY-102 under the increasing heat load.

This document lists safety class (SC) and safety significant (SS) components for the Heating Ventilation Air Conditioning (HVAC) and specifies the critical characteristics for Commercial Grade Items (CGI), as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to properly perform its safety function. There may be several manufacturers or models that meet the critical characteristics for any one item.

Appropriations are one part of a complex federal budget process that includes budget resolutions, appropriations (regular, supplemental, and continuing) bills, rescissions, and budget reconciliation bills. This report is a guide to one of the 13 regular appropriations bills that Congress passes each year. It is designed to supplement the information provided by the House and Senate Defense Appropriations Subcommittees.

The simulation of the Auxiliary Charcoal Bed (ACB) Vacuum System was performed to evaluate the original vacuum system design, detect and identify design deficiencies, investigate the effects of proposed corrections on system performance, and generally aid in refining the system design before construction and mockup testing. The simulation was performed by using the Advanced Continuous Simulation Language (ACSL). The vacuum system design goals are to provide approximately 20 SCFM of both booster gas and purge gas through the system and maintain a flow of approximately 40 SCFM with a velocity of 50 to 75 f/sec at the entrance to the cyclone separator. The model results showed that the original system design was incapable of meeting the system performance goals. Further simulations showed that the following modifications to the original vacuum system design were required to make the system performance acceptable; (1) Remove valve PCV4. (2) Modify the flow controllers FTC3 and FTC4 from the original flow range of 0-17.6 SCFM (0-500 SLM) to 0-35.3 SCFM (0-1000 SLM). (3) Replace the bellows sealed valves SV-1, SV-3A, SV-3B, SV-4A, and SV-4B with less restrictive ball valves. The simulation results saved considerable time and effort by identifying flaws in the original system design. …

Room temperature (RT) pulsed operation of blue nitride based multi-quantum well (MQW) laser diodes grown on c-plane sapphire substrates was achieved. Atmospheric pressure MOCVD was used to grow the active region of the device which consisted of a 10 pair In{sub 0.21}Ga{sub 0.79}N (2.5nm)/In{sub 0.07}Ga{sub 0.93}N (5nm) InGaN MQW. The threshold current density was reduced by a factor of 2 from 10 kA/cm{sup 2} for laser diodes grown on sapphire substrates to 4.8 kA/cm{sub 2} for laser diodes grown on lateral epitaxial overgrowth (LEO) GaN on sapphire. Lasing wavelengths as long as 425nm were obtained. LEDs with emission wavelengths as long as 500nm were obtained by increasing the Indium content. These results show that a reduction in nonradiative recombination from a reduced dislocation density leads to a higher internal quantum efficiency. Further research on GaN based laser diodes is needed to extend the wavelength to 490nm which is required for numerous bio-detection applications. The GaN blue lasers will be used to stimulate fluorescence in special dye molecules when the dyes are attached to specific molecules or microorganisms. Fluorescein is one commonly used dye molecule for chemical and biological warfare agent detection, and its optimal excitation wavelength is 490 nm. InGaN …

Temperature programmed desorption (TPD) was performed at temperatures up to 850K on Cab-O-Sil-M-7D and Hi-Sil-233 silica particles. Physisorbed water molecules on both types of silica had activation energies in the range of 9-14.5 kcal/mol. However, the activation energies of desorption for chemisorbed water varied from {approx} 19 kcal/mol to > 59 kcal/mol for Cab-O-Sil-M-7D, and {approx} 23-37 kcal/mol for Hi-Sil-233. Our results suggest that physisorbed water can be effectively pumped away at room temperature (or preferably at 320 K) in a matter of hours. Chemisorbed water with high activation energies of desorption (>30 kcal/mol) will not escape the silica surfaces in 100 years even at 320 K, while a significant amount of the chemisorbed water with medium activation energies (19-26 kcal/mol) will leave the silica surfaces in that time span. Most of the chemisorbed water with activation energies < 30 kcal/mol can be pumped away in a matter of days in a good vacuum environment at 500 K. We had previously measured about 0.1-0.4 wt. % of water in M9787 polysiloxane formulations containing {approx} 21% Cab-O-Sil-M-7D and {approx} 4% Hi-Sil-233. Comparing present results with these formulations, we conclude that absorbed H{sub 2}O and Si-OH bonds on the silica surfaces are …

This report summarizes experimentally and numerically determined modal properties for one of the reinforced concrete end walls of the NIF Periscope Support Structure in Laser Bay 1. Two methods were used to determine these modal properties: (1) Computational finite-element analyses (modal extraction process); and (2) Experimental modal analysis based on measured test data. This report also includes experimentally determined modal properties for a prototype LM3/Polarizer line-replaceable unit (LRU) and a prototype PEPC LRU. Two important parameters, used during the design phase, are validated through testing [ref 1]. These parameters are the natural frequencies and modal damping (of the system in question) for the first several global modes of vibration. Experimental modal testing provides these modal values, along with the corresponding mode shapes. Another important parameter, the input excitation (expected during normal operation of the NIF laser system) [ref 1], can be verified by performing a series of ambient vibration measurements in the vicinity of the particular system (or subsystem) of interest. The topic of ambient input excitation will be covered in a separate report. Due to the large mass of the Periscope Pedestal, it is difficult to excite the entire series of Periscope Pedestal Walls all at once. It was …