We discuss recent developments in III-V multijunction solar cells, focusing on adding a fourth junction to the Ga0.5In0.5P/GaAs/Ga0.75In0.25As inverted three-junction cell. This cell, grown inverted on GaAs so that the lattice-mismatched Ga0.75In0.25As third junction is the last one grown, has demonstrated 38% efficiency, and 40% is likely in the near future. To achieve still further gains, a lower-bandgap GaxIn1-xAs fourth junction could be added to the three-junction structure for a four-junction cell whose efficiency could exceed 45% under concentration. Here, we present the initial development of the GaxIn1-xAs fourth junction. Junctions of various bandgaps ranging from 0.88 to 0.73 eV were grown, in order to study the effect of the different amounts of lattice mismatch. At a bandgap of 0.88 eV, junctions were obtained with very encouraging {approx}80% quantum efficiency, 57% fill factor, and 0.36 eV open-circuit voltage. The device performance degrades with decreasing bandgap (i.e., increasing lattice mismatch). We model the four-junction device efficiency vs. fourth junction bandgap to show that an 0.7-eV fourth-junction bandgap, while optimal if it could be achieved in practice, is not necessary; an 0.9-eV bandgap would still permit significant gains in multijunction cell efficiency while being easier to achieve than the lower-bandgap junction.

None

Fact sheet describes the study being conducted on fuel cell buses at AC Transit.

Metagenome studies have retrieved vast amounts of sequenceout of a variety of environments, leading to novel discoveries and greatinsights into the uncultured microbial world. Except for very simplecommunities, diversity makes sequence assembly and analysis a verychallenging problem. To understand the structure a 5 nd function ofmicrobial communities, a taxonomic characterization of the obtainedsequence fragments is highly desirable, yet currently limited mostly tothose sequences that contain phylogenetic marker genes. We show that forclades at the rank of domain down to genus, sequence composition allowsthe very accurate phylogenetic 10 characterization of genomic sequence.We developed a composition-based classifier, PhyloPythia, for de novophylogenetic sequence characterization and have trained it on adata setof 340 genomes. By extensive evaluation experiments we show that themethodis accurate across all taxonomic ranks considered, even forsequences that originate fromnovel organisms and are as short as 1kb.Application to two metagenome datasets 15 obtained from samples ofphosphorus-removing sludge showed that the method allows the accurateclassification at genus level of most sequence fragments from thedominant populations, while at the same time correctly characterizingeven larger parts of the samples at higher taxonomic levels.

None

Among the infrequently measured but essential properties for thin-film (T-F) module reliability are the interlayer adhesion and cohesion within a layer. These can be cell contact layers to glass, contact layers to the semiconductor, encapsulant to cell, glass, or backsheet, etc. We use an Instron mechanical testing unit to measure peel strengths at 90{sup o} or 180{sup o} and, in some cases, a scratch and tape pull test to evaluate inter-cell layer adhesion strengths. We present peel strength data for test specimens laminated from the three T-F technologies, before and after damp heat, and in one instance at elevated temperatures. On laminated T-F cell samples, failure can occur uniformly at any one of the many interfaces, or non-uniformly across the peel area at more than one interface. Some peel strengths are << 1 N/mm. This is far below the normal Instron mechanical testing unit Instron mechanical testing unit; glass interface values of >10 N/mm. We measure a wide range of adhesion strengths and suggest that adhesion measured under higher temperature and relative humidity conditions is more relevant for module reliability.

This document reports the technical results of the Next Generation Turbine Development Project conducted by GE Wind Energy LLC. This project is jointly funded by GE and the U.S. Department of Energy's National Renewable Energy Laboratory.The goal of this project is for DOE to assist the U.S. wind industry in exploring new concepts and applications of cutting-edge technology in pursuit of the specific objective of developing a wind turbine that can generate electricity at a levelized cost of energy of $0.025/kWh at sites with an average wind speed of 15 mph (at 10 m height).

The Advanced Graphite Capsule (AGC) irradiation test program supports the acquisition of irradiated graphite performance data to assist in the selection of the technology to be used for the VHTR. Six irradiations are planned to investigate compressive creep in graphite subjected to a neutron field and obtain irradiated mechanical properties of vibrationally molded, extruded, and iso-molded graphites for comparison. The experiments will be conducted at three temperatures: 600, 900, and 1200°C. At each temperature, two different capsules will be irradiated to different fluence levels, the first from 0.5 to 4 dpa and the second from 4 to 7 dpa. AGC-1 is the first of the six capsules designed for ATR and will focus on the prismatic fluence range.

N/A

Air tightness is an important property of building envelopes. It is a key factor in determining infiltration and related wall-performance properties such as indoor air quality, maintainability and moisture balance. Air leakage in U.S. houses consumes roughly 1/3 of the HVAC energy but provides most of the ventilation used to control IAQ. The Lawrence Berkeley National Laboratory has been gathering residential air leakage data from many sources and now has a database of more than 100,000 raw measurements. This paper uses that database to develop a model for estimating air leakage as a function of climate, building age, floor area, building height, floor type, energy-efficiency and low-income designations. The model developed can be used to estimate the leakage distribution of populations of houses.

A number of experimental techniques are currently being deployed in an effort to make the first detection of ultra-high energy cosmic neutrinos. To accomplish this goal, techniques using radio and acoustic detectors are being developed, which are optimally designed for studying neutrinos with energies in the PeV-EeV range and above. Data from the AMANDA experiment, in contrast, has been used to place limits on the cosmic neutrino flux at less extreme energies (up to {approx}10 PeV). In this letter, we show that by adopting a different analysis strategy, optimized for much higher energy neutrinos, the same AMANDA data can be used to place a limit competitive with radio techniques at EeV energies. We also discuss the sensitivity of the IceCube experiment, in various stages of deployment, to ultra-high energy neutrinos.

The summary of this report is that amorphous InZnO (a-IZO) is a very versatile TCO with: (1) low process temperatures ({approx} 100 C); (2) easy to make by sputtering; (3) excellent optical and electronic properties; (4) very smooth etchable films; and (5) remarkable thermal processing stability.

An analog signal pre-processing scheme was developed, in the framework of the Fermilab Main Injector Beam Position Monitor (BPM) Upgrade, to interface BPM pickup signals to the new digital receiver based read-out system. A key component is the 8-channel electronics module, which uses separate frequency selective gain stages to acquire 53 MHz bunched proton, and 2.5 MHz anti-proton signals. Related hardware includes a filter and combiner box to sum pickup electrode signals in the tunnel. A controller module allows local/remote control of gain settings and activation of gain stages, and supplies test signals. Theory of operation, system overview, and some design details are presented, as well as first beam measurements of the prototype hardware.

Article for the Journal of Solar Energy Engineering which analyzes system and wind energy data recorded by WFEC and evaluates the effects of wind energy on system operations.

Multi-particle simulations are performed to study emittance growth in the Fermilab Booster. Analysis shows that the source of vertical emittance growth comes mostly from random errors in skew quadrupoles in the presence of a strong transverse space-charge force. [1] Random errors in dipole rolls and the Montague resonance do contribute but to lesser extent. The effect of random errors in the quadrupoles is small because the betatron envelope tunes are reasonably far away from the half-integer stopband.

Long-range forces between macroscopic objects are mediated by light particles that interact with the electrons or nucleons, and include spin-dependent static components as well as spin- and velocity-dependent components. We parametrize the long-range potential between two fermions assuming rotational invariance, and find 16 different components. Applying this result to electrically neutral objects, we show that the macroscopic potential depends on 72 measurable parameters. We then derive the potential induced by the exchange of a new gauge boson or spinless particle, and compare the limits set by measurements of macroscopic forces to the astrophysical limits on the couplings of these particles.

None

The U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory (NREL) is seeking government, private, or non-profit partners to design, construct, and assist in operating one or more wind turbine blade test facilities capable of testing blades up to at least 70 m (230 ft) in length. DOE/NREL encourages interested parties to respond to this CRADA announcement with a proposal by September 1, 2006.

We present a new thin-film solar cell structure in which the traditional transparent conductive oxide electrode (ZnO) is replaced by a transparent conductive coating consisting of a network of bundled single-wall carbon nanotubes. Optical transmission properties of these coatings are presented in relation to their electrical properties (sheet resistance), along with preliminary solar cell results from devices made using CuIn1-xGaxSe2 thin-film absorber materials. Achieving an energy conversion efficiency of >12% and a quantum efficiency of {approx}80% demonstrate the feasibility of the concept. A discussion of the device structures will be presented considering the physical properties of the new electrodes comparing current-voltage results from the new solar cell structure and those from standard ZnO/CdS/Cu(In,Ga)Se2/Mo solar cells.

This report talks about Assessment of Load and Energy Reduction Techniques (ALERT) Report for Department of Energy Rocky Mountain Oilfield Testing Center Casper Wyoming.

California electric utilities have been exploring the use of dynamic critical peak pricing (CPP) and other demand response programs to help reduce peaks in customer electric loads. CPP is a new electricity tariff design to promote demand response. This paper begins with a brief review of terminology regarding energy management and demand response, followed by a discussion of DR control strategies and a preliminary overview of a forthcoming guide on DR strategies. The final section discusses experience to date with these strategies, followed by a discussion of the peak electric demand savings from the 2005 Automated CPP program. An important concept identified in the automated DR field tests is that automated DR will be most successful if the building commissioning industry improves the operational effectiveness of building controls. Critical peak pricing and even real time pricing are important trends in electricity pricing that will require new functional tests for building commissioning.

Recent results on heavy flavor spectroscopy from the CDF and D0 experiments are reported in this contribution. Using up to 1 fb{sup -1} of accumulated luminosity per experiment, properties of X(3872), excited B** states, and the B{sub c} meson are measured. Also included are measurements of production rates for ground state b hadrons in p{bar p} collisions.

The identification of jets resulting from the fragmentation and hadronization of b quarks is an important part of high-p{sub T} collider physics. The methods used by the CDF and D0 collaborations to perform this identification are described, including the calibration of the efficiencies and fake rates. Some thoughts on the application of these methods in the LHC environment are also presented.

Measurement of the B{sub s}{sup 0} oscillation frequency via B{sub s}{sup 0} mixing analysis provides a powerful constraint on CKM matrix elements. This note briefly reviews the motivation behind these analyses and describes the various steps that go into a mixing measurement. Recent results on B{sub s}{sup 0} mixing obtained by the CDF and D0 collaborations using the data samples collected at Tevatron Collider in the period 2002-2005 are presented.