A 2-D finite element code has been developed for the solution of arbitrary geometry cable SGEMP and box IEMP problems. The quasi- static electric field equations with radiation- induced charge deposition and radiation-induced conductivity y are numerically solved on a triangular mesh. Multiple regions of different dielectric materials and multiple conductors are permitted.

This paper will focus on the methodology of using a 2D plasma Direct Simulation Monte Carlo technique to simulate the species transport in an inductively coupled, low pressure, chemically reacting plasma system. The pressure in these systems is typically less than 20 mtorr with plasma densities of approximately 10{sup 17} {number_sign}/m{sup 3} and an ionization level of only 0.1%. This low ionization level tightly couples the neutral, ion, and electron chemistries and interactions in a system where the flow is subsonic. We present our strategy and compare simulation results to experimental data for Cl{sub 2} in a Gaseous Electronics Conference (GEC) reference cell modified with an inductive coil.

In anticipation of increasingly stringent environmental regulations, Lawrence Livermore National Laboratory (LLNL) proposes to construct a 60 kilogram (kg) firing chamber to provide blast-effects containment for most of its open-air, high explosives, firing operations. Even though these operations are within current environmental limits, containment of the blast effects and hazardous debris will further drastically reduce emissions to the environment and minimize the generated hazardous waste.

The magnetic field design for a 600 MeV proton cyclotron is described. The cyclotron has a single stage, a normal conducting magnet coil and a 9.8 m outside yoke diameter. It has 8 sectors, with a transition to 4 sectors in the center region. The magnetic field design was done using 1958 Harwell rectangular ridge system measurements and was compared with recent 3-dimensional field calculations with the program TOSCA at NSCL. The center region 4--8 sector transition focussing was also checked with TOSCA.

Science took the front seat as 219 Advanced Light Source (ALS) users and staff gathered on Monday and Tuesday, October 18 and 19 for the twelfth annual users' meeting. The bulk of the meeting was dedicated to reports on science at the ALS. Packed into two busy days were 31 invited oral presentations and 80 submitted poster presentations, as well as time to visit 24 vendor booths. The oral sessions were dedicated to environmental science, chemical dynamics, biosciences, magnetic materials, and atomic and molecular science. In addition, there was an ALS highlights session that emphasized new results and a session comprising highlights from the young scientists who will carry the ALS into the future.

Given the events of the past 25 years concerning energy and environmental issues and our reaction to them, what lessons can we learn? First, the individual American consumer wants and expects energy to be a stable commodity with low prices and easy availability. As evidenced by the heated debate over increasing the federal gasoline tax by $.05 per gallon (which would still leave Americans paying only one-third of what Europeans pay for gasoline), increases in energy prices elicit very strong public and political opposition. As further evidence, it has been argued that the general public support of the Gulf War was due, in part, to a recognition of the need to maintain a stable source of cheap oil from the region. The American public wants to maintain the benefits of cheap and abundant energy and expects its political leaders to make it happen. A second lesson is that if constraints on the energy supply do occur (e.g., the OPEC-imposed oil embargo) ardor environmental impacts from energy use do appear to be significant (e.g., SO{sub 2} and CO{sub 2} emissions), the preference is for a technology fix rather than a behavioral change. This is evidenced by our reliance on moving low-sulfur …

The assay of highly enriched {sup 233}U material presents some unique challenges. Techniques which apply to the assay of materials of Pu or enriched {sup 235}U do not convert easily over to the assay of {sup 233}U. A specialized neutron assay device is being fabricated to exploit the singles neutron signal, the weak correlated neutron signal, and an active correlated signal. These pieces of information when combined with {gamma} ray isotopics information should give a good overall determination of {sup 233}U material now stored in bldg. 3019 at the Oak Ridge National Laboratory.

Using adaptive optics the authors have obtained nearly diffraction-limited 5 kJ, 3 nsec output pulses at 1.053 {micro}m from the Beamlet demonstration system for the National Ignition Facility (NIF). The peak Strehl ratio was improved from 0.009 to 0.50, as estimated from measured wavefront errors. They have also measured the relaxation of the thermally induced aberrations in the main beam line over a period of 4.5 hours. Peak-to-valley aberrations range from 6.8 waves at 1.053 {micro}m within 30 minutes after a full system shot to 3.9 waves after 4.5 hours. The adaptive optics system must have enough range to correct accumulated thermal aberrations from several shots in addition to the immediate shot-induced error. Accumulated wavefront errors in the beam line will affect both the design of the adaptive optics system for NIF and the performance of that system.

We have developed amplitude and phase modulation systems for glass lasers using integrated electro-optic modulators and solid state high- speed electronics. The present and future generation of lasers for Inertial Confinement Fusion require laser beams with complex temporal and phase shaping to compensate for laser gain saturation, mitigate parametric processes such as transverse stimulated Brillouin scattering in optics, and to provide specialized drive to the fusion targets. These functions can be performed using bulk optoelectronic modulators, however using high-speed electronics to drive low voltage integrated optical modulators has many practical advantages. In particular, we utilize microwave GaAs transistors to perform precision, 250 ps resolution temporal shaping. Optical bandwidth is generated using a microwave oscillator at 3 GHz amplified by a solid state amplifier. This drives an integrated electrooptic modulator to achieve laser bandwidths exceeding 30 GHz.

The third hypervariable domain of the HIV-1 gp120 envelope protein (V3) has been the focus of intensive sequencing efforts. To date, nearly one thousand V3 loop sequences have been stored in the HIV sequence database. Studies have revealed that the V3 loop elicits potent type-specific immune responses, and that it plays a significant role in cell tropism and fusion . The immunogenic tip of the loop can serve as a type-specific neutralizing antibody epitope, as well as a cytotoxic T-cell epitope. A helper T-cell epitope that lies within the amino terminal half of the V3 loop has also been characterized. Despite the richness of the immunologic response to this region, its potential for variation makes it an elusive target for vaccine design. Analyses of sibling sequence sets (sets of viral sequences derived from one person) show that multiple forms of the immunogenic tip of the loop are found within most HIV-1 infected individuals. Viral V3 sequences obtained from epidemiologically unlinked individuals from North America and Europe show extensive variation. However, some amino acid positions distributed throughout the V3 loop are highly conserved, and there is also conservation of the charge class of amino acid able to occupy certain positions relative …

The third hypervariable domain of the HIV-1 gp120 envelope protein (V3) has been the focus of intensive sequencing efforts. To date, nearly one thousand V3 loop sequences have been stored in the HIV sequence database. Studies have revealed that the V3 loop elicits potent type-specific immune responses, and that it plays a significant role in cell tropism and fusion . The immunogenic tip of the loop can serve as a type-specific neutralizing antibody epitope, as well as a cytotoxic T-cell epitope. A helper T-cell epitope that lies within the amino terminal half of the V3 loop has also been characterized. Despite the richness of the immunologic response to this region, its potential for variation makes it an elusive target for vaccine design. Analyses of sibling sequence sets (sets of viral sequences derived from one person) show that multiple forms of the immunogenic tip of the loop are found within most HIV-1 infected individuals. Viral V3 sequences obtained from epidemiologically unlinked individuals from North America and Europe show extensive variation. However, some amino acid positions distributed throughout the V3 loop are highly conserved, and there is also conservation of the charge class of amino acid able to occupy certain positions relative …

The purpose of this work was to investigate the utility of electronic aroma detection technologies for the detection and identification of accelerant residues in suspected arson debris. Through the analysis of known accelerant residues, a trained neural network was developed for classifying suspected arson samples. Three unknown fire debris samples were classified using this neural network. The item corresponding to diesel fuel was correctly identified every time. For the other two items, wide variations in sample concentration and excessive water content, producing high sample humidities, were shown to influence the sensor response. Sorbent sampling prior to aroma detection was demonstrated to reduce these problems and to allow proper neural network classification of the remaining items corresponding to kerosene and gasoline.

The National Ignition Facility (NIF) laser will use a 192-beam multi-pass architecture capable of delivering several MJ of UV energy in temporal pulse formats varying from sub-ns square to 20 ns precisely-defined high-contrast shapes. Each beam wavefront will be subjected to effects of optics inhomogeneities, figuring errors, mounting distortions, prompt and slow thermal effects from flashlamps, driven and passive air-path turbulence, and gravity-driven deformations. A 39-actuator intra-cavity deformable mirror, controlled by data from a 77-lenslet Hartman sensor will be used to correct these wavefront aberrations and thus to assure that stringent farfield spot requirements are met. We have developed numerical models for the expected distortions, the operation of the adaptive optic system, and the anticipated effects on beam propagation, component damage, frequency conversion, and target-plane energy distribution. These models have been extensively validated against data from LLNL's Beamlet, and Amplab lasers. We review the expected beam wavefront aberrations and their potential for adverse effects on the laser performance, describe our model of the corrective system operation, and display our predictions for corrected-beam operation of the NI

As any structure ages, its structural characteristics will also change. The goal of this work was to determine if modal response data fkom a wind turbine could be used in the detection of damage. The input stimuli to the wind turbine were from traditional modal hammer input and natural wind excitation. The structural response data was acquired using accelerometers mounted on the rotor of a parked and undamaged horizontal-axis wind turbine. The bolts at the root of one of the three blades were then loosened to simulate a damaged blade. The structural response data of the rotor was again recorded. The undamaged and damage-simulated datasets were compared using existing darnage detection algorithms. Also, a novel algorithm for combining the results of different damage detection algorithms was utilized in the assessment of the data. This paper summarizes the code development and discusses some preliminary damage detection results.

While Magnetic X-ray Circular Dichroism (MXCD) has been applied extensively to the extraction of elemental magnetic moments in various magnetic multilayers, the configuration of actual devices imposes certain constraints on the application of MXCD to devices. Using a set of real, thin-film spin valve devices with varying Cu spacer layer thicknesses, we demonstrate the correlation between MXCD and R-H measurements on those devices as well as the restrictions on the interpretation of MXCD data imposed by both the device topology and the formulation of realistic error estimates.

Today's insurance industry strongly emphasizes developing cost-effective hazard mitigation programs, increasing and retaining commercial and residential customers through better service, educating customers on their exposure and vulnerabilities to natural disasters, collaborating with government agencies and emergency management organizations, and exploring the use of new technologies to reduce the financial impact of disasters. In June of 1998, the National Renewable Energy Laboratory (NREL) and the National Association of Independent Insurers (NAII) sponsored a seminar titled, ''Solar Technology and the Insurance Industry.'' Presentations were made by insurance company representatives, insurance trade groups, government and state emergency management organizations, and technology specialists. The meeting was attended by insurers, brokers, emergency managers, and consultants from more than 25 US companies. Leading insurers from the personal line and commercial carriers were shown how solar technology can be used in underwriting, claims, catastrophe response, loss control, and risk management. Attendees requested a follow-up report on solar technology, cost, and applications in disasters, including suggestions on how to collaborate with the utility industry and how to develop educational programs for business and consumers. This report will address these issues, with an emphasis on pre-disaster planning and mitigation alternatives. It will also discuss how energy efficiency and renewable …

A new method of ultrasensitive isotope trace analysis has been developed. This method, based on the technique of laser manipulation of neutral atoms, has been used to count individual {sup 85}Kr and {sup 81}Kr atoms present in a natural krypton gas sample with isotopic abundances in the range of 10{sup {minus}11} and 10{sup {minus}13}, respectively. This method is free of contamination from other isotopes and elements and can be applied to several different isotope tracers for a wide range of applications. The demonstrated detection efficiency is 1 x 10{sup {minus}7}. System improvements could increase the efficiency by many orders of magnitude.

The optical arrangement of the scanning transmission electron microscope (STEM) allows formation of incoherent images by use of a large annular detector. Here we show this capability in the imaging of defects in GaN and the interfacial region of an Au/GaAs ohmic contact. A resolution of around 0.15 nm is attained. Such Z-contrast images show strong atomic number contrast and allow the probe to be positioned accurately at the defect or interface for the purpose of performing high spatial resolution electron energy-loss spectroscopy (EELS).

We presents results from a predictive atomic level simulation of Boron diffusion in Silicon under a wide variety of implant and annealing conditions. The parameters for this simulation have been extracted from first principle approximation models and molecular dynamics simulations. The results are compared with experiments showing good agreement in all cases. The parameters and reactions used have been implemented into a continuum-level model simulator.

We describe the use of automatic differentiation (AD) to enhance a compressible Navier-Stokes model. With the solver, AD is used to accelerate convergence by more than an order of magnitude. Outside the solver, AD is used to compute the derivatives needed for optimization. We emphasize the potential for performance gains if the programmer does not treat AD as a black box, but instead utilizes high-level knowledge about the nature of the application.

The Beaverhead impact structure in SW Montana and Idaho is an allochthonous fragment of a large impact structure ({approximately} 100 km diameter) that was transported some distance eastward during the Cretaceous Sevier orogeny. It is the first tectonic fragment of a large impact structure identified in the geologic record. The present evidence for impact consists of shatter cones, pseudotachylites, and planar deformation features in quartz. The age of the impact is not well constrained but is estimated to be Neoproterozoic to Cambrian (1000-500 Ma). The Beaverhead impact event must have created other features that may be preserved, elsewhere in western Montana and Idaho. These include proximal and distal ejecta (which may be misinterpreted as diamictites and/or tuff horizons) and other fragments of the crater floor containing shatter cones and pseudotachylite. A large circular gravity, magnetic and topographic anomaly, which could be the root of the impact structure, has been identified near Challis, Idaho. An enigmatic lithic tuff, identified in drill cores from the Challis area and an intraformational quartzite breccia in the Leaton Gulch area may be impact-related deposits, but no definitive evidence of shock metamorphism has been observed in these materials. The discovery of more pieces of the Beaverhead …

Contamination of soils, water, and sediments by radionuclides and toxic metals from uranium mill tailings, nuclear fuel manufacturing and nuclear weapons production is a major concern. Studies of the mechanisms of biotransformation of uranium and toxic metals under various microbial process conditions has resulted in the development of two treatment processes: (i) stabilization of uranium and toxic metals with reduction in waste volume and (ii) removal and recovery of uranium and toxic metals from wastes and contaminated soils. Stabilization of uranium and toxic metals in wastes is accomplished by exploiting the unique metabolic capabilities of the anaerobic bacterium, Clostridium sp. The radionuclides and toxic metals are solubilized by the bacteria directly by enzymatic reductive dissolution, or indirectly due to the production of organic acid metabolites. The radionuclides and toxic metals released into solution are immobilized by enzymatic reductive precipitation, biosorption and redistribution with stable mineral phases in the waste. Non-hazardous bulk components of the waste such as Ca, Fe, K, Mg and Na released into solution are removed, thus reducing the waste volume. In the second process uranium and toxic metals are removed from wastes or contaminated soils by extracting with the complexing agent citric acid. The citric-acid extract is …

Accurate estimation of the depth of partial-thickness burns and the early prediction of a need for surgical intervention are difficult. A non-invasive technique utilizing the difference in thermal relaxation time between burned and normal skin may be useful in this regard. In practice, a thermal camera would record the skin's response to heating or cooling by a small amount-roughly 5{degrees} Celsius for a short duration. The thermal stimulus would be provided by a heat lamp, hot or cold air, or other means. Processing of the thermal transients would reveal areas that returned to equilibrium at different rates, which should correspond to different burn depths. In deeper thickness burns, the outside layer of skin is further removed from the constant-temperature region maintained through blood flow. Deeper thickness areas should thus return to equilibrium more slowly than other areas. Since the technique only records changes in the skin's temperature, it is not sensitive to room temperature, the burn's location, or the state of the patient. Preliminary results are presented for analysis of a simulated burn, formed by applying a patch of biosynthetic wound dressing on top of normal skin tissue.

The Relativistic Heavy Ion Collider RHIC will collide polarized proton beams up to a maximum beam energy of 250 GeV [1]. The invariant spin field in a high energy ring can vary substantially across the beam. This decreases the amount of polarization provided to experiments and makes the polarization strongly dependent on the position in phase space. This paper describes a method to compute the invariant spin field by adiabatically blowing up the beam with an rf dipole. This method will also allow measuring the invariant spin field in RHIC.