Abstract; The fission product data obtained during SM-1 Core I operation (June 1957 - May 1960) is reviewed briefly and interpreted. Evidence is presented to indicate that a fuel element defect was responsible for the high fission product activity level observed in the primary coolant. Relative escape coefficients are calculated and the defect size estimated. Anticipated fission product levels during SM-1 Core II and SM-1A Core I operation are estimated from alpha surface contamination data on completed fuel elements. The importance of in-line sampling for monitoring fission product activity is stressed as well as the need for failed fuel element detection methods.

Abstract; This technical report describes the changes in the SM-1 incurred by the experiment, Core Temperature and Flow Instrumentation (Task XIV), and evaluates the possible hazard involved in these changes. Temperature and flow measurements will be taken on a Task XIV instrumented stationary fuel element, instrumented control rod fuel element and other selected points in the SM-1 core to provide data on the core steady state and transient performance. The hazards evaluation consists of a nuclear evaluation, thermal and hydraulic analysis, description of tests to be performed, and discussion of containment integrity and maximum accident considerations.

Abstract: This technical report describes the as-constructed SM-1 penetrated gasket designed for SM-1 Core and Flow Instrumentation (Task XIV). This report supplements APAE No. 79, The Summary Hazards Report for Task XIV, and evaluates the effects of a postulated failure of this gasket. The effects of failure on the Maximum Credible Accident are determined and conclusions and recommendations for the use of this gasket are made.

Introduction: This is a final report on the evaluation of Kanigen electroless nickel plating for surfaces in contact with water and steam i a sodium heated AISI Type 316 stainless steel steam generator. The purpose of the coasting was to afford protection from stress corrosion cracking originating on the water-steam side of the unit. It has been concluded that the kanigen coating does not afford adequate protection for the services condition intended. This work was performed as part of the research and development program for the United States Atomic Energy Commission sodium Components Design Project.

Abstract; The heat exchanger and steam generator for the U.S. Atomic Energy Commission Sodium Components Project will be constructed entirely of type 316 stainless steel. Because of the susceptibility of this alloy to stress corrosion cracking, it is proposed to clad all areas of the steam generator with Inconel where the stainless steel will be exposed to water and steam. This report includes a discussion of the work by numerous investigators that justify the selection of Inconel for this service. A discussion of Inconel type welding alloys is also included.

Abstract: This technical report describes the changes incurred in the SM-1 by the insertion of the SM-1 Core II and special components. The special components consist of impact specimens, a boron gradient rod, SM-2 elements, a PM-1-M element, and high burnup SM-1 Core I elements. The change in hazards, due to operation of SM-1 with Core II and the special components is evaluated. The analysis indicates there is no change in hazards.

Abstract: This technical report describes the changes incurred in the SM-1 by the insertion of the SM-1 Core II without special components. The SM-1 Core II components were made to specifications very nearly identical to those of SM-1 Core I. The differences consist of europium absorber sections, internal europium flux suppressors in the control rod fuel elements, and low impurity cladding. Each of the SM-1 Core II components with the exception of the five absorber sections new in SM-1 Core I were subjected to a Zero Power Experiment at the Alco Critical Facility. The results of this experiment indicate that the SM-1 Core II will have nuclear characteristics very similar to that of the SM-1 Core I. Since SM-1 Core II will be operated with the same mode of rod control, in the same core support structure, and with the same primary coolant flow conditions, the thermal characteristics should be essentially identical to that of SM-1 Core I. Also, all kinetic characteristics of SM-1 Core II should be identical to those of SM-1 Core I. This report demonstrates that there is no increase in potential for a hazardous situation at SM-1 due to the replacement of SM-1 Core I by …

Abstract: This technical report describes the Martin Co. PM-1-M-2 test element and analyzes the potential hazard incurred by its inclusion in the SM-1 Core II. A nuclear analysis develops power distributions and reactivity effects. Hydraulic and thermal analyses develop anticipated burnout heat flux ratios. An evaluation of the risk involved with the inclusion of this element is presented. In view of the narrow margin by which the PM-1-M-2 test element meets the minimum burnout ratios as defined by Alco Products, Inc., it is recommended that if time permits that critical facility design verification be accomplished. The PM-1-M-2 test element meets the minimum requirements for insertion in SM-1 Core II and in view of the importance of this element to the PM-1 and PM-3A program, should be considered for insertion.

Abstract: The removal of both SM-1 Core I high burnup elements from SM-1 Core II and the insertion of the PM-1-M-2 element and the SM-1 Core I spare element in SM-1 Core II is discussed. Nuclear and thermal characteristics of Core II with these changes are presented and conclusions related to the changes in the hazard potential are made. If the core change indicated by this report is made, local peaking factors will be decreased and burnout ratios will be increased. This, of course, in itself leads to a more conservative estimate of core safety. There is no conceivable reason why the perturbation may not be safely made in the SM-1 Core II.

Abstract: This technical report contains a summary of analytical and experimental work performed on SM-1 Core II, with special components is presented. The effects of these special assemblies upon power distribution and core reactivity were calculated and compared to experimental measurements. A thermal analysis was conducted to determine steady state and transient performance of the special test components of the core as well as some of the hotter standard Core II components. Experimental work discussed includes individual reactivity effects of all the special elements and the total effect of all of the elements. Power mappings were also made and are reported.

Abstract: A cyclic stress analysis of the SM-1 primary system was carried out. Problems encountered in the fabrication of PM-2A Core II and SM-lA Core II are described, and the results of an examination of damaged SM-lA Core I stationary fuel elements reported. A preliminary study of the radiation damage to SM-1 reactor vessel was made and the possibility of annealing the vessel discussed. Performance analyses are presented for five cores: SM-1 Core, SM-1 Core 1 rearranged and spiked, SM-1 Core II with special components, PM-2A Core 1, and SM- 1A Core 1. Preliminary critical experiments were made with SM-2 elements in a SM- 1 core configuration and nuclear and thermal analyses of the use of SM-2 elements in SM-1, SM-1A, and PM-2A completed. A throttling steam calorimeter was selected for measuring moisture carry-over on the PM-2A steam generator. Test procedures for evaluating the shielding of the SM-1, SM-lA, and PM-2A plants are summarized. Radiochemical and chemical analyses of SM-1 coolant and crud are summarized, and methods of activity control discussed. Preliminary results of studies of the properties of reactor pressure vessels under irradiation and no irradiation conditions are summarized briefly.

Abstract; SM-1 Reactor Core I Rearranged and Spiked, and Core II with Special Components were analyzed under various off-design conditions to induce nucleate boiling. The steady state code, STDY-3, written for the thermal analysis of pressurized water cores, was employed for the analysis. The code performs a complete steady state parallel channel thermal analysis for both nominal and hot channels. Thermal characteristics of individual elements were investigated while changing the parameters of primary pressure or inlet temperature to introduce the phenomenon of nucleate boiling in the the core. Reduction of system pressures to 1000, 800, and 600 psia and increasing core inlet temperatures to 465 and 500 degree F were studied as the means to induce boiling in the core. This analysis indicates that SM-1 Core I Rearranged and Spiked can be safely operated at the reduced pressure of 910 psia without introducing extensive boiling in the core. SM-1 Core II with Special Components can be operated at 800 psia or at an inlet temperature of 500 degree F at 1200 psia.

Abstract: Thermal characteristics of the SM-2 core were analyzed at steady state and loss of flow conditions. For steady state operation, the steady state code STDY-3 was used. For transients during a loss of flow accident, ART-02, a one-dimensional code, was used. This analysis indicates the SM-2 core is safe from burnout under steady state operation at design power level (28 tMW) because (1) no nucleate boiling exists, and (2) the minimum burnout ratio is above 2.0. The core is safe from burnout under loss of flow transient because the minimum burnout ratio in the hottest element channel of 1. 82 is above the minimum design criteria of 1. 5.

Abstract: This technical report presents design criteria to prevent the brittle fracture of ferritic reactor vessels that cold occur as a result of the rise in NDT caused by fast neutron irradiation. The criteria require that maximum principal stress in the vessel does not exceed 18 percent of yield stress at temperatures below NDT + 60 degree F. Under certain conditions the allowable stress may be based on the irradiated yield stress. A discussion of brittle fracture and an explanation of the criteria are included.

Abstract: This technical report elucidates principles of hazards evaluation. The concept of hazards potential is introduced and utilized to show how a reactor system perturbation will influence its nuclear safety. Literature relating to reactor safety is referenced to provide the sources of information required for hazards analysis and show how they influence a hazards evaluation. A checklist of items which should be considered in evaluating a change, test, or modification is presented.

Abstract: This technical report contains a description and results of a second series of critical experiments performed on the SM-2 core mock-up, as additional to the first series of experiments reported in APAE No. 54. The SM-2 core mock-up contains 36.4 kg U-235 and and estimated 67.9 gm B-10. The equivalent diameter and the active height are about 22 in.; the metal-to-water volume ration is 0.344. Data is presented on activation, reactivity, and stuck rod measurements. All measurements were conducted on the open seven control rod array employing 38 stationary fuel elements. Activation measurements consisted of neutron flux measurements using uranium fission foils for relative power distribution studies, the effect of flux suppressors on reducing power peaks, blocked coolant channel measurements, and gamma ray dose distribution. Reactivity measurements were performed to determine the effect f flow divider, flux suppressors and stimulated high temperature and pressure operation; b-10 loading in the SM-2 core; and core material coefficients. For the later, the worth in cents per gm or cents per cc was determined at simulated temperature of 510 degree F for B-10, U-235, stainless steel, and void. Stuck rod measurements were made to obtain an indication of the criticality margin in the …

Abstract: The removal of both SM-1 Core I high burnup elements from the SM-1 Core II and the insertion of two SM-1 Core I spare elements i their places are discussed. Nuclear and thermal characteristics of Core II with the change are presented and conclusion related to the change in hazard potential are made. If the core change indicated by this report is made, local peaking factors will be decreased and burnout ratios will be increased. This, of course, in itself leads to a more conservative estimate of core safety. There is no conceivable reason why this perturbation may not be safely made in the SM-1 Core II.

Abstract: Hydrodynamic flow studies were conducted on a full scale model of the SM-2 reactor vessel and core. Test fluid was water at 200 psi and 200 degree F. Test facilities, model, and instrumentation design are discussed. Flow distribution in the stationary fuel elements, lattices, and control rods of the second pass was investigated. Pressure losses through the various core components were measured and are compared with calculated values. Observed over-all pressure drop was 71 feet of water at 200 degree F, 31% higher than predicted, part of which was due to presence of instrument leads. Element to element flow distribution varied approximately +-8% from pass average. Channel-to-channel stationary element flow distribution varied approximately +-10% from element average and control rod flow distribution varied from +-8.9% to +-6.4 and -11.6% depending upon rod locations. These variations exceed the original goals of a +-10% and +-12% combined deviation for stationary and control rod elements respectively, but are satisfactory in relation to thermal design. There was no indication of unsatisfactory structural performance of any components under hydrodynamic loadings up to 130% of design values. The test program was terminated after determining flow distribution in the reference core design, omitting any work on …