Technical report of a proposal of an analytical model to predict two-phase critical flow rate. The model is based upon thermal equilibrium, a "lumped" treatment of the two-phase velocity (each phase is represented by a single mean velocity), and upon the neglect of frictional and hydrostatic pressure losses. A comparison, of the proposed predictions with available test results and previous analyses shows that: (1) The present model agrees very well with the published test data. (2) In contrast to all other analyses, the model requires no assumption about the gas void fraction.

Summary: Stainless steel clad nuclear fuel cycle costs can be reduced to those associated with Zircaloy clad fuel or potentially lower by reducing the thickness of the clad tube wall until performance penalties offset the savings associated with the reduction in parasitic neutron absorption. To demonstrate the feasibility and investigate performance capabilities of thin clad fuel rods for power reactor application an assembly was fabricated with 0.0127 cm (5 mil) thick stainless steel cladding tubes for irradiation testing in the Vallecitos Boiling Water Reactor (VBWR). The fuel bundle was placed in the VBWR and irradiation was begun in November, 1961. The irradiation is scheduled to continue until the target exposure of 2.74 x 10(20) fissions/cc (10,000 MWD/T of uranium) average burnup is reached. Destructive examinations of fuel rods will be performed at regular intervals throughout life to determine fuel rod performance.

Technical report describing that as part of the AEC Fuel Cycle Program, tests are being conducted to evaluate the significance of current fuel design limitations that do not permit the maximum fuel temperature to exceed the melting point of UO2. The reliability of prediction of the fuel rod operating conditions that will cause melting of the UO2 was evaluated by means of a calibration test conducted in the Vallecitos Boiling Water Reactor. Conclusions: (a) The central portion of the 3.15-cm diameter uranium dioxide fuel column melted. It appears that the UO2 was molten to a radius of 1.22 cm in the peak power region. The maximum extent of melting probably occurred during the peak power run when the kdT in this region of the rod reached 171 watts cm. The estimated radius of melting from metallographic examination indicates the kdT for sintered UO2 is 89 watts/cm. This supports a calculated estimate for sintered UO2 thermal conductivity published by D. R. deHalas and G. R. Horn. The results of the previous calibration run and subsequent experimental data by Lyons are also consistent with the value. This conclusion is contingent on the interpretation of the post-irradiation crystal structure of the UO2. Insufficient …

Abstract: A core design study of a 10 Mwe fast ceramic reactor is presented. Local reactivity coefficients, safety criteria, accident analyses, and economics are considered. An attempt is made to find a new balance of characteristics by purely geometric devices, i.e., by exploring the sodium : fuel ratio and varying the height : diameter ratio of the core. The use of BeO in the core was also investigated.

From introduction: "This is the seventeenth in a series of quarterly reports which cover the progress and results from the conceptual designs, economic evaluations and research and development work performed by the General Electric Company as part of Contract AT(01-3)-189, Project Agreement No. 13."

The influence of the Doppler effect in the core disassembly process following a meltdown accident is examined with a Bethe-Tait type model in which the Doppler effect, as well as core disassembly, is considered in the reactor shutdown process. It is shown that a strong negative Doppler effect can radically reduce the explosive energy release in such an accident. (auth)

Abstract: The physical property variation of superheated steam differs sufficiently from most other gases to warrant experimental investigation of heat transfer performance. Results are reported here of measurements made in a uniformly heated circular duct with steam at 1000 psi. The data agree very well with the expression use for design purposes, which is based on information in the literature for heating of other gases as well as steam. This work was a continuation of that performed under Task (Heat Transfer) of the Nuclear Superheat Project, AEC Contract AT(04-3)-189, Project Agreement 13.

This technical report describes the development, design, operation, and performance of a full-circle, radial-vane steam separator for the boiling water section of a nuclear superheat reactor. Steam-water tests of this model have demonstrated that is has vane capacity in excess of that required for the 300-Mx(e) separate superheat reactor and for the 300-Mw mixed spectrum superheat reactor. It is proposed that the vane capacity requirement of the 600 Mw(e) separate superheat reactor may be attained by increasing the nozzle length.

Quarterly progress report on Accurate Nuclear Fuel Burnup Analysis project.

Introduction: The purpose of this technical report is to review the water chemistry methods and equipment developed for use with the Maritime Loop Irradiation Program conducted in the General Electric Test Reactor (GETR) from December 2, 1960 to July 19, 1962. Special emphasis is given to areas having general application to other high purity water systems. The Appendix includes a discussion of specific conductivity and pH in high purity water systems. A major section of this report is devoted to a review of gross activity levels on coupons of two different surface finishes exposed in the loop coolant system for various time intervals. A major objective of the chemistry program was to select or develop analytical methods such that the analyses could be performed at the loop location by technical personnel who normally operate the loop. By this means, frequent samples were obtained and analyzed directly thus providing close monitoring and control of the loop water chemistry at minimum expense.

Summary: A prototype control rod containing absorber plates made from an electro- deposited dispersion of boron carbide in nickel was tested in the VBWR. It was exposed to the reactor environment of 545 degree F boiling water and thermal neutron fluxes (perturbed) which ranged from 0.6 to 1.1 x 10/sup 13/ nv for 2236 hours over a period of six months. The maximum B/sup 10/ burnup achieved during the test period was 1.8 percent. After irradiation, the rod was examined. The results of the examination are summarized below: (1) The B/sub 4/C-- Ni plate assembly did not undergo significant dimensional changes during irradiation. (2) Numerous blisters developed on both the outer and inner surfaces of three of the four plates. Blistering was more severe on the outer surface than on the inner, and was most severe in a large region located in the lower half of plate 4. Metallographic examination revealed that the blisters were located only in the 2- mil protective nickel overlay covering the B/sub 4/C-- Ni dispersion. It was concluded that they formed from the buildup of gas pressure at the Ni: Ni-- B/sub 4/C interfaces, rather than from corrosion attack. Helium from the B/sup 10/(n alpha …

Activities in a program to develop techniques in the use of pulsed neutron sources to measure shutdown parameters related to large thermal power reactors are reported. The development of pulsed neutron source techniques for large power reactors has led to a new theoretical model recently developed by E. Garelis and J.L. Russell, Jr. The theory is presently based on a bare, one-group model with m-delayed precursors and takes all spatial modes into account. Results indicate, however, that the application of this model is much broader. Experiments were designed and carried out to both verify this new theory and to demonstrate the performance of the experimental hardware in a large power reactor.

Abstract: Neutron flux and gamma radiation measurements through the SM-1 primary shield were made at the startup of Core II in June 1961. They extend previous measurements (APAE-35) both vertically and horizontally in the primary shield and in the rod drive pit. Dose rate measurements on spent fuel elements under water are also reported.

Abstract: This technical report analyzes gamma dose rate and neutron measurements in their relation to the SM-1 shield design and is a continuation of previous shielding measurements and analyses reported in APAE-35 and APAE-35 Supplement 2. The data reported herein are spent fuel element and rod drive pit gamma dose rates. An analysis of gamma dose rates off the core midplane is presented and compared with test data.

Abstract: This technical report contains a description and results of a second series of critical experiments performed on the SM-2 core mock-up, as additional to the first series of experiments reported in APAE No. 54. The SM-2 core mock-up contains 36.4 kg U-235 and and estimated 67.9 gm B-10. The equivalent diameter and the active height are about 22 in.; the metal-to-water volume ration is 0.344. Data is presented on activation, reactivity, and stuck rod measurements. All measurements were conducted on the open seven control rod array employing 38 stationary fuel elements. Activation measurements consisted of neutron flux measurements using uranium fission foils for relative power distribution studies, the effect of flux suppressors on reducing power peaks, blocked coolant channel measurements, and gamma ray dose distribution. Reactivity measurements were performed to determine the effect f flow divider, flux suppressors and stimulated high temperature and pressure operation; b-10 loading in the SM-2 core; and core material coefficients. For the later, the worth in cents per gm or cents per cc was determined at simulated temperature of 510 degree F for B-10, U-235, stainless steel, and void. Stuck rod measurements were made to obtain an indication of the criticality margin in the …

Abstract: This technical report is concerned with the program and results of the SM-1 reactor vessel head removal and core inspection at Fort Belvoir, Virginia from the period March 7, 1969 to May 17, 1959. It covers the operating procedures in detail and records the conditions found and problems encountered in order to make a record for reference in future work of this nature. The major objective of the program, to obtain irradiation data on the SM-1 type core, has been met. The boron control rod elements were found unsatisfactory for full core life, and europium oxide elements were placed in the core for future irradiation stability data. A major problem was experienced with the cracked pressure vessel head studs. The methods developed for the removal of the broken studs are presented. The complete metallurgical study of the stud failure from stress corrosion is included as Appendix B.

Abstract: This technical report summarizes the data obtained in a recent literature survey conducted to determine the effects of neutron irradiation on the impact and other mechanical properties of both ferritic steels and austenitic stainless steels. The survey was primarily aimed at obtaining sufficient data on the behavior of pressure vessel steels at high integrated neutron flux levels in order that a reference material of construction could be selected for the SM-2 (APPR-1B) reactor vessel. Materials studied in this literature survey included carbon and low alloy steels such as: ASTM A-212B, ASTM A-201, ASTM A-301B (CR-Mo), ASTM A-106 (coarse and fine grained), ASTM A-285, ASTM A-302B (Mn-Mo), ASTM A-353, ASTM A-203 Grade D, E-7016 carbon steel weld metal, USS Carilloy T-1, HY-65 and HY-80. In addition, Types 304 and 347 stainless steels were also investigated as representative austenitic materials which might be used in pressure vessel construction. A careful evaluation was made of the irradiation induced changes in the mechanical properties of the above materials. The ferritic steels were evaluated primarily on the basis of increases in transition temperature due to irradiation and decreases in the amount of maximum energy absorbed prior to ductile failure. Factors such as industrial experience, …

Abstract: The removal of both SM-1 Core I high burnup elements from the SM-1 Core II and the insertion of two SM-1 Core I spare elements i their places are discussed. Nuclear and thermal characteristics of Core II with the change are presented and conclusion related to the change in hazard potential are made. If the core change indicated by this report is made, local peaking factors will be decreased and burnout ratios will be increased. This, of course, in itself leads to a more conservative estimate of core safety. There is no conceivable reason why this perturbation may not be safely made in the SM-1 Core II.

Abstract: Development of welding processes for stainless steel fuel elements, previously initiated by Alco Products, was continued in Task 5. Three objectives were accomplished; (1) development of a suitable reference welding process, (2) evaluation by out-of-pile tests of the structural integrity of reference welded fuel elements, and (3) preparation of specifications and fabrication procedures for the reference welding process.

Abstract: The results of activity buildup studies in the SM-1 performed during Core I lifetime (June 3, 1957 to April 28, 1960) are reported. Data are presented on the extent, nature, and mechanism of the buildup of long-lived gamma emitting nuclides in the reactor primary system. Radiation levels after reactor shutdown are presented, as well as mathematical equations used to account for the observed activity levels. The data have shown that Co60 is the major contributor to radiation levels in the SM-1. Co60 activity arises from the cobalt in Haynes 25 alloy flux suppressors, and the cobalt impurity in stainless steel. After 35 months operation at an average power level of 55%, deposited Co60 activity accounted for approximately 83% of the total radiation level (mr/hr) contributed by the long-lived gamma emitting nuclides. The contribution of the primary coolant activity to the total radiation level is insignificant when compared to the contribution of the activity deposited on the walls of the system. The radiation level on the super-heater side of the steam generator was about 1400 mr/hr after 35 months of reactor operation. The percentages of Co60 activity in the coolant and in the deposits were not the same. This indicates …

Abstract: A zero power experiment on the SM-1 Core II included an element by element reactivity check of fuel elements and control rod absorber sections, and an estimate of burnable nuclear poison loading in stationary fuel elements. An approach to criticality was made by the inverse multiplication method, and critical rod bank position obtained as a function fuel loading up to full core loading. Minimum and maximum core reactivity measurements were obtained by selective loading of stationary fuel elements, and total excess K of the core was established. Power distribution measurements were taken in the regions of the core-reflector interface and the fuel-absorber interface in the control rod assemblies. The effectiveness of europium flux suppressors in the top of control rod fuel elements was determined, and power peaking was measured in stationary elements adjacent to control rod assembly water gaps. Survey measurements established the work of spiking clean, cold SM-1 cores with SM-2 elements and the work of water holes in the SM-1 Core. The reduced scope zero power experiment performed on SM-1A core I included an element by element uniformity check of stationary fuel elements, a core assembly test, comparison of Eu2O3 and B4C absorber sections, and development of …

Abstract: An element by element reactivity check for SM-1 Core II fuel elements and control rod absorber sections was performed and the burnable nuclear poison loading in the SM-1 Core II stationary fuel elements was established. An approach to criticality of the SM-1 Core II was performed by the inverse multiplication method and the critical rod bank position obtained as a function of fuel loading up to the full SM-1 Core II loading. Maximum and minimum core reactivity measurements were obtained by selective loading of stationary fuel elements and the total "excess K" for the core established. Power distribution measurements in the region of the core-reflector interface and the fuel-absorber interface in the control rod assemblies were performed. The effectiveness of europium flux suppressors in the top of control rod fuel elements and the power peaking in stationary elements adjacent to water gaps in control rod assemblies were measured. Survey measurements established the worth of spiking cold clean SM-1 cores with SM-2 elements, and of water holes in the SM-1 core which might be utilized as flux traps for materials irradiation.

Abstract: Hydrodynamic flow studies were conducted on a full scale model of the SM-2 reactor vessel and core. Test fluid was water at 200 psi and 200 degree F. Test facilities, model, and instrumentation design are discussed. Flow distribution in the stationary fuel elements, lattices, and control rods of the second pass was investigated. Pressure losses through the various core components were measured and are compared with calculated values. Observed over-all pressure drop was 71 feet of water at 200 degree F, 31% higher than predicted, part of which was due to presence of instrument leads. Element to element flow distribution varied approximately +-8% from pass average. Channel-to-channel stationary element flow distribution varied approximately +-10% from element average and control rod flow distribution varied from +-8.9% to +-6.4 and -11.6% depending upon rod locations. These variations exceed the original goals of a +-10% and +-12% combined deviation for stationary and control rod elements respectively, but are satisfactory in relation to thermal design. There was no indication of unsatisfactory structural performance of any components under hydrodynamic loadings up to 130% of design values. The test program was terminated after determining flow distribution in the reference core design, omitting any work on …

Abstract This technical report covers the thermal analysis performed on the SM-1 Core III for both steady state and transient conditions is reported. SM-1 Core III will be used as a test for Type 3 elements in a PM-2A Core. The steady state analysis indicated minimum departure from nucleate boiling ratios (DNBR) for both design and scram conditions above the minimum criteria of 1.5. Local nucleate boiling was noted in the hot internal channels and lattice passage at scram power conditions. Loss of flow transient results indicate DNBR's above 1.5, insuring that the core is safe from burnout. Bulk boiling was noted in the hot channels and lattice passage at scram power condition.