The objective of the Accurate Nuclear Fuel Burnup Analyses program is to develop more accurate methods for burnup analysis for general use than the current method of analysis of Ca-137 or Sr-90. The program will require from three to five years of effort.

The objective of the Accurate Nuclear Fuel Burnup Analyses program is to develop more accurate methods for burnup analysis for general use than the current method of analysis of Ca-137 or Sr-90. The program will require from three to five years of effort.

Quarterly progress report on Accurate Nuclear Fuel Burnup Analysis project.

Technical report describing a UO2-Mo cermet fuel assembly fabricated for long-term irradiation performance testing in the Vallecitos Boiling water Reactor. The design and fabrication histories of this assembly are described and pre-irradiation data on each individual rod are presented. Molybdenum was added to improve the bulk thermal conductivity of the fuel, so that fuel temperatures would remain comparatively low during high-power level operation of the fuel element. The molybdenum was incorporated into the compacts either as fibers or as a thin coating on individual UO2 particles. Fuel pellets were produced from these materials by vacuum hot pressing. The distribution of the molybdenum in both types of cermet fuels appeared favorable to good heat transfer. The fibers were oriented predominantly in the radial planes of the pellet as a result of the uni-directional compaction during the hot-pressing operation. In the pellets made from the coated particles, a continuous network of molybdenum occurred as a result of the coating welding together during the hot-pressing operation. The test assembly contains eight fuel rods; three contain UO2-Mo cermet, three contain the cermet produced from the coated particles, and two are for reference and contain the conventional sintered UO2 pellet fuel. The nominal outside diameter …

The extrusion forming of ceramic powders may be economically interesting in the field of nuclear fuel fabrication. When applied to the forming of rod-type uranium dioxide fuel, extrusion processes have been able to produce cylindrical bodies with length-to-diameter ratios much greater than those of the conventional die-pressed pellets. Furthermore, after being sintered, the extrusions have exhibited densities at least as high as those of sintered pellets. Thus, extrusion forming may offer reductions in handling during fabrication and, at the same time, provide a fuel with improved performance characteristics by decreasing the number of discontinuities in the fuel column. This report reviews the production of these extrusions, sets forth some of their characteristics, describes the materials and processes employed in cladding them, and records the pre-irradiation data pertaining to the finished fuel rods and fuel assembly. Irradiation of the fuel assembly in the VBWR was initiated on July 17, 1962.

Summary: Stainless steel clad nuclear fuel cycle costs can be reduced to those associated with Zircaloy clad fuel or potentially lower by reducing the thickness of the clad tube wall until performance penalties offset the savings associated with the reduction in parasitic neutron absorption. To demonstrate the feasibility and investigate performance capabilities of thin clad fuel rods for power reactor application an assembly was fabricated with 0.0127 cm (5 mil) thick stainless steel cladding tubes for irradiation testing in the Vallecitos Boiling Water Reactor (VBWR). The fuel bundle was placed in the VBWR and irradiation was begun in November, 1961. The irradiation is scheduled to continue until the target exposure of 2.74 x 10(20) fissions/cc (10,000 MWD/T of uranium) average burnup is reached. Destructive examinations of fuel rods will be performed at regular intervals throughout life to determine fuel rod performance.

Activities in a program to develop techniques in the use of pulsed neutron sources to measure shutdown parameters related to large thermal power reactors are reported. The development of pulsed neutron source techniques for large power reactors has led to a new theoretical model recently developed by E. Garelis and J.L. Russell, Jr. The theory is presently based on a bare, one-group model with m-delayed precursors and takes all spatial modes into account. Results indicate, however, that the application of this model is much broader. Experiments were designed and carried out to both verify this new theory and to demonstrate the performance of the experimental hardware in a large power reactor.

Activities in a program to develop techniques in the use of pulsed neutron sources to measure shutdown parameters related to large thermal power reactors are reported. In the course of this program, a new theory was suggested and an experimental apparatus was designed and built. Experiments were carried out to test the new model. This present report contains additional data and information extracted from the experiments at PG&E Humboldt Bay Power Reactor at Eureka, California. During the last days of 1963 a number of control rod and fuel bundle worth measurements were made in the ESADA Vallecitos Experimental Superheat Reactor (EVESR) using the (k[beta]/[script l] technique. A description of the experiments is given in the text of the report and some results are reported. A computer program was written to perform the data analysis of the pulsed neutron experiments and the code is discussed in the Appendix.

Activities in a program to develop techniques in the use of pulsed neutron sources to measure shutdown parameters related to large thermal power reactors are reported. The development of pulsed neutron source techniques for large power reactors has led to a new theoretical model recently developed by E. Garelis and J.L. Russell, Jr. The theory is presently based on a bare, one-group model with m-delayed precursors and takes all spatial modes into account. Results indicate, however, that the application of this model is much broader. Experiments were designed and carried out to both verify this new theory and to demonstrate the performance of the experimental hardware in a large power reactor.

Summary: A prototype control rod containing absorber plates made from an electro- deposited dispersion of boron carbide in nickel was tested in the VBWR. It was exposed to the reactor environment of 545 degree F boiling water and thermal neutron fluxes (perturbed) which ranged from 0.6 to 1.1 x 10/sup 13/ nv for 2236 hours over a period of six months. The maximum B/sup 10/ burnup achieved during the test period was 1.8 percent. After irradiation, the rod was examined. The results of the examination are summarized below: (1) The B/sub 4/C-- Ni plate assembly did not undergo significant dimensional changes during irradiation. (2) Numerous blisters developed on both the outer and inner surfaces of three of the four plates. Blistering was more severe on the outer surface than on the inner, and was most severe in a large region located in the lower half of plate 4. Metallographic examination revealed that the blisters were located only in the 2- mil protective nickel overlay covering the B/sub 4/C-- Ni dispersion. It was concluded that they formed from the buildup of gas pressure at the Ni: Ni-- B/sub 4/C interfaces, rather than from corrosion attack. Helium from the B/sup 10/(n alpha …

Technical report describing sixteen fuel rods clad with thin type 304 stainless steel and filled with vibratory compact powder UO2 that were fabricated and incorporated into a bundle for irradiation testing in the VBWR. The UO2 powders were tested for gas content. N2, CO, and H2 were the principal gases evolved by both type of UO2, but the arc-fused UO2 released about ten times as much gas as the Dyna Pak UO2. The amount of gas released was also a function of particle size and temperature. The gas evolution data were used to design the gas plenum to accommodate the absorbed gases along with the fission gases.

Quarterly progress report discussing activities related to the Vallecitos Boiling Water Reactor (VBWR) and related facilities.

Summary: The High Power Density Project includes a comprehensive fuel development program which has the objective of developing and demonstrating the performance of a nuclear reactor core having a high power density, long fuel life, and low fabrication cost. The fuel program is made up of two principal tasks. Task 1A consists of irradiation tests in the VBWR of Type 304 stainless steel clad, UO2 pellet type fuel rods fabricated by current commercial processes. Task 1B consists of the investigation of lower cost fabrication processes and the irradiation testing of fuel elements fabricated by these processes. Both tasks include the investigation of the feasibility and use of thin-wall stainless steel cladding as a means of improving the neutron economy and fuel cycle costs of stainless steel clad fuel. Irradiation of the Task 1A fuel assemblies in the VBWR was initiated in September, 1960. Subsequently, Task 1B fuel assemblies were inserted in the VBWR as various fabrication processes and design concepts were investigated. Fuel cladding failures have occurred in fuel rods in both Task 1A and 1B. As of this date, cladding failures have occurred in twenty-two rods of approximately 700 fuel rods which have been irradiated. Twenty of the failures …

Abstract: The physical property variation of superheated steam differs sufficiently from most other gases to warrant experimental investigation of heat transfer performance. Results are reported here of measurements made in a uniformly heated circular duct with steam at 1000 psi. The data agree very well with the expression use for design purposes, which is based on information in the literature for heating of other gases as well as steam. This work was a continuation of that performed under Task (Heat Transfer) of the Nuclear Superheat Project, AEC Contract AT(04-3)-189, Project Agreement 13.

Development of nuclear reactor cores having high power density, long fuel life, and low fabrication costs is the objective of this program sponsored by the AEC. Five tasks are in progress: (1) Task 1A-High Power Density Fuel Development. All fuel irradiation has been terminated with the final shutdown of the VBWR. The high burnup average achieved by a single assembly in the group is 10,000 MWD/T (assembly 1F). Twenty-one of the original 24 assemblies have failed or are suspected of failure. Profilometer tests rung on HPD assembly 2E, Rod B, indicate that localized clad deformation occurs during operation. (2) Task 1B-Fuel Fabrication Development. Assembly. All fuel irradiation has been terminated with the final shutdown of the VBWR. The highest average burnup achieved by a single assembly in the group was assembly 4S with 8400 MWD/T. All assemblies in the group have failed or are suspected of failure. The Phase I developmental fuel continues to be irradiated in the Big rock Point reactor with the lead assembly having reached 1500 MWD/T. Fifteen phase II developmental assemblies are being construction for insertion at Big Rock Point in March. Engineering is underway to provide one instrumented assembly probe and two spare flowmeters for …

Development of nuclear reactor cores having high power density, long fuel life, and low fabrication costs is the objective of this program sponsored by the AEC. Five tasks are in progress: (1) Task 1A-High Power Density Fuel Development. The number of assemblies has been reduced to seven as a result of the failure of two pellet fuel assemblies. The average burnup of the group operating as of September 1 is 7500 MWD/T. (2) Task 1B-Fuel Fabrication Development. Assembly. Assembly 12S gave positive signals of being a leaker under the multi-type in-core sampler and was declared failed based on the in-core results and visual observation of a cracked rod. Modifications to the instrumented fuel assembly probes were made by removing the failed flow meter rotors to allow continued use of the flux detectors and thermocouples. Flux detectors and thermocouples performed properly after reactor start up. Flux wire tubes were found to be kinked such that their use was prohibited. (3) Task II-Stability, Heat Transfer and Fluid Flow. A series of noise recordings of fluxes, flows, and temperatures has been made at 91 MWt at the Big Rock Point plant. Preliminary analyses of some of the these records were made to obtain …

Summary: Technical report describing the testing of eight Potter Meters, for metering inlet flow and measuring exit steam qualities in the Consumers Big Rock Point Instrumented Fuel Assemblies, were individually calibrated for flow and pressure drop up to 500 gpm in the low temperature (130 F) fluid flow facility. The flow calibration comparison made with an ASME orifice installation, agreed to within + - 1 percent among seven of the meters, and meter Serial No. 8 was 2.8 percent lower than the others. Pressure drop among the meters was within about 5 percent. Locked rotor pressure drop data was obtained on one meter. A fully instrumented fuel bundle was tested in the low temperature facility and pressure drop data obtained for the tieplates and meters, spacers, and channel rods. A mock-up of the exit end of the instrumented fuel bundles, composed of 1 foot of fuel rods, tieplate, and Potter Meter was tested in the High Pressure Heat Transfer Facility. Data was obtained for single- and two-phase calibration of total flow and exit steam quality in an instrumented bundle. Each meter was operated, for a minimum of 6-8 hours after bearing modifications necessitated by seizure of the rotors, in the …

Development of nuclear reactor cores having high power density, long fuel life, and low fabrication costs is the objective of this program sponsored by the AEC. Five tasks are in progress: (1) Task 1A-High Power Density Fuel Development, (2) Task 1B-Fuel Fabrication Development. Assembly, (3) Task II-Stability, Heat Transfer and Fluid Flow, (4) Task III-Physics Development, and (5) Task IV-Co-Ordination and Test Planning.

The objective of Project Agreement 22 is to determine the feasibility of using in-core ion chambers to cover the complete reactor neutron flux startup range from 10(4) -5 - 10(13) nv using in-core ion chambers. This technical report discusses the following topics: low versus high cable termination impedance, amplifier considerations, noise considerations, gas and pressure selection, cable selection, effect of gamma, effect of temperature, and remaining problems.

Introduction: The objective of Project Agreement 22 is to determine the feasibility of covering the complete reactor neutron flux start range from 10(3) - 5 x 10(13) nv by using in-core chambers. The counting mode of operating will be used at low neutron fluxes and the root mean square voltage fluctuation mode will be used at high neutron flux levels. Experiments have been run utilizing various ion chambers, gases, gas pressures, voltage, and cables to measure sensitivities and range operating in the counting and RMS voltage modes. Theoretical discussions are presented showing how the RMS voltage is related to individual pulse at both amplifier input and output. Noise is also compared at amplifier output so that the optimum bandwidth can be selected. Spectral shifts with changes in applied voltage causing signal variations have been examined and can be eliminated by appropriate selection of amplifier bandwidth. In the counting mode, all experiments have been conducted with unterminated cable. The chamber has been designed with geometry, gas, and pressure to completely stop fission fragments in the gas and hence maximize the charge generated in the chamber. Cables have been selected to minimize capacity. Various gases, pressures, and voltages have been used to …

Introduction: The objective of Project Agreement 22 is to determine the feasibility of using in-core ion chambers to cover the complete reactor neutron flux startup range from 10(4) -5 - 10(13) nv using in-core ion chambers. The counting mode of operation will be used at low neutron flux levels and the RMS voltage fluctuation mode (Campbell Theorem) will be used at high neutron flux levels. The June-September Progress Report (GEAP-4386) shows how the RMS voltage mode can be used, discusses counting problems with long cable and ways of maximizing signal levels. This report discusses primarily the effect of gamma on counting with in-core ion chambers and the range of neutron flux measurable in the RMS voltage mode. Readers are referred to GEAP-4386 for a summary of all previous progress to attain the objective of PA-22.

The influence of the Doppler effect in the core disassembly process following a meltdown accident is examined with a Bethe-Tait type model in which the Doppler effect, as well as core disassembly, is considered in the reactor shutdown process. It is shown that a strong negative Doppler effect can radically reduce the explosive energy release in such an accident. (auth)

Abstract: A stainless steel clad 9-rod assembly fabricated by The Babcock & Wilcox Company was irradiated in a boiling water loop of the General Electric Test Reactor. A post-irradiation examination revealed no significant dimensional changes on the fuel rods. the results of mass spectrometric analysis made of the pelletized UO2 fuel indicated a maximum burnup of 11,500 MWD/tonne was attained by Rod B-4 during the exposure.An x-ray diffraction examination of an unirradiated fuel sample revealed the presence of UN2 and U2N3 phases. Metallographic examination of the irradiated microstructures revealed similar second-phase particles.

Introduction: The purpose of this technical report is to review the water chemistry methods and equipment developed for use with the Maritime Loop Irradiation Program conducted in the General Electric Test Reactor (GETR) from December 2, 1960 to July 19, 1962. Special emphasis is given to areas having general application to other high purity water systems. The Appendix includes a discussion of specific conductivity and pH in high purity water systems. A major section of this report is devoted to a review of gross activity levels on coupons of two different surface finishes exposed in the loop coolant system for various time intervals. A major objective of the chemistry program was to select or develop analytical methods such that the analyses could be performed at the loop location by technical personnel who normally operate the loop. By this means, frequent samples were obtained and analyzed directly thus providing close monitoring and control of the loop water chemistry at minimum expense.