"A convenient summary is given of useful formulas on the kinematics of high energy electron scattering together with a derivation of the relevant formulas for transforming from the center of mass to the laboratory system such parameters as scattering cross sections. The formulas derived hold for any two- body collision: the approximation (m = 0) employed for the electron scattering calculations is rigorously true for the elastic scattering of photons."

Potential methods have been examined for the reclamation of high boiler arising from the degradation of polyphenol materials in use as reactor coolants and moderators. To define the chemistry of potential reclamation processes, model polyphenol compounds were used. These include biphenyl, o, m and p-terphenyl, and p-quaterphenyl. Emphasis has been on hydrocracking, redistribution (reaction with benzene), and partial reduction. Preliminary study has been made of the application these techniques to high boiler from Santowax-OM used in the OMRE. The three methods show promise but require detailed investigation to minimize carbon formation to locate optimum operating conditions,.

The report covers work performed during the period September 1, 1959 through September 30, 1959. The general objectives of the program of "Studies of Reactor Containment" are to accomplish theoretical and experimental investigations of the loads to which external containment structures for nuclear reactors are subjected in the vent of a violent incident at the reactor core, the evaluation of methods of reducing that loading, and the study of the response of and design criteria for external containment structures as a result of such loading. Progress of technical effort during the report period is summarized for each of the eight tasks of the program.

This review lists some of the salient features of semiconductor particle counters and cannot claim to contain an exhaustive listing of all the work in the field. Performance results on the surface-barrier counters as developed at California Institute of Technology are included as typical for this type of counter, though comparable results have been obtained elsewhere.

The purpose of the test was to determine if failed blanket elements exist in other regions of the core beside F-2. FEDAL sampling ports that have indicted the greatest deviation as determined in a statistical analysis performed on a number of traverses in the FEDAL system will be tested. Data obtained from the start up runs of the FEDAL sample port Nos. 11, 31, 36 and 37 of Monitor 2 and port Nos. 14, 46, 11, 49 and 7 of Monitor 1 gave no indications of a blanket element failure. At each power increase, the radiation increase was normal with no signs of bursts or peaks of radiation which would indication the failure of a blanket fuel element.

The PWR Plant was operated at approximately 60 MW net electrical output for a total of 1000 EFPH from February 3, 1959 to March 28, 1959. During this period, while performing DL-S-225, there were two planned shutdowns, no safety shutdowns or safety insertions and one flux title. The performance of the plant was satisfactory during the period of the test.

Experiments are described which show that the velocity of compressional waves along a thin plate varies as a function of the frequency of the waves. In terms of transit times in aluminum the value is between 4.02 and 4.94 microseconds per inch.

Ultrasonic inspection for subsurface flaws is widely used in American industry. This report reviews the general principles and specific techniques of ultrasonic testing. The information is based on a review of the technical literature plus the experience of the Quality Assurance Department at Sandia Corporation in applying this nondestructive testing technique to quality evaluation programs.

The nil-ductility-transition (NDT) temperature, as defined by the Naval Research Laboratory drop-weight test, was determined on the A212B carbon-silicon steel used in the pressure vessel of the N. S. Savannah nuclear reactor. Correlations were made with the Charpy-V-notch impact energy at NDT. Specimens taken at two different thickness location from materials used in the upper closure head of the reactor vessel yielded NDT temperatures of 0 - 20°F which correspond to Charpy-V-notch impact energies of 11-19 ft-lb. Testing of as-received material used in the lower closure head indicated that the NDT temperature was 50°F which was equivalent to an average Charpy-V-notch impact energy of 12 ft-lb. After normalizing and stress-relieving this material, in order to more closely approximate the final condition of the reactor vessel, NDT was reduced to less than 10°F.

The preliminary process design of a PRFR pilot leaching plant, which is proposed to be located in Cell B of Building ORNL, is considered. Chemical, physical, and nuclear parameters are investigated in order that the leaching operations may be carried out without any chemical or nuclear hazards.

The Turco 4501 process is recommended for the decontamination of the PRFR pilot leaching plant equipment. The caustic-tartrate-nitric acid process is recommended for the decontamination of the cell and the equipment exterior.

The Lindemann assumption of direct contact of neighboring atoms at fusion is replaced by the criterion that melting occurs when the root-mean-square amplitude of thermal vibration reaches a critical fraction ρ, presumed the same for all isotropic monatomic solids, of the distance of separation of nearest-neighbor atoms. The Debye-Waller theory of the temperature dependence of the intensity of Bragg reflection of x-rays is used, without further assumptions, to derive a generalized Lindemann law. In contrast to the Lindemann form, all physical quantities involved in this formulation are evaluated at the fusion point, and departure of the average energy of an atomic oscillation from the equipartition value is taken into account by the quantization factor of the Debye-Waller theory. If the Grüneisen constant γm of the solid at fusion is evaluated by its definition from the Debye frequency of the solid, use of the generalized Lindemann law and Clapeyron's equation permits one to express γm in terms of the bulk modulus of the solid at melting and the latent heat and volume change of fusion. By means of Grüneisen's law applied to the solid at fusion, γm can be expressed likewise in terms of the corresponding bulk modulus, thermal expansion, volume, …

A generalization of the Fermi-Thomas model for application of mixtures. This study attempts to determine the equation of state of water up to pressure of 10,000 megabars and temperatures of several thousand electron-volts.

At the request of the Alloy Preparation Group, the Nondestructive Test Development Group investigated the feasibility of determining the clad thickness on Mark X MTR Fuel Plates. As the use of induced eddy-currents was considered to be the most promising approach, a prototype instrument and probe coil utilizing this principle was developed to measure clad thickness. The results of the investigation conducted with this instrument indicate that the clad thickness of this type of fuel plats can be measured to withing +- 0.001 in.

The countercurrent gas-liquid system BF3(g)—anisole·BF3(l) for the concentration of boron isotopes has been studied. The single-storage separation factor varies from 1.039 at 0°C to 1.029 at 30°C. Rate of exchange is rapid, and, with efficient contacting equipment, complete exchange may be obtained in less than 15 sec. A total separation of 1.525 has been realized in laboratory equipment. The critical-product reflux reaction is quite efficient. Only about 55 moles of BF3 remain in each million moles of effluent solvent under laboratory conditions. The vapor pressure of BF3 over the complex rises sharply as the temperature is increased. At 0°C the pressure is 150 mm Hg, and at 40°C the pressure has risen to 1800 mm Hg. From vapor-pressure measurements, an approximate upper limit of ΔH= -12kcal per mole of complex was calculated for the reaction [equation not transcribed]. Qualitative tests indicate good resistance of anisole to decomposition by BF3 under plant conditions. The uncatalyzed exchange of boron between BF3 and BCl3 was found to be too slow to be exploited in a countercurrent system. The single-stage, equilibrium separation factor for the Nitrox system is a function of acid concentration. At 26°C the factor ranges from 1.064 with 1 M acid …

The flux through a given region is proportional to the total lengths of the neutron flight paths that intersect that region. The analytical Monte Carlo procedure manufactured neutron flight paths and totaled the lengths of all paths intercepted by the regions illustrated in Figure 1. The procedure was designed to utilize the various symmetries in the lattice. / Consider a portion of the lattice whose planar cross-section is shown in Figure 5. If R is the region in which the flux is to be estimated and F the fuel rod in which the neutron originated, then flight path P results in an intercepted length whose reflection in the plane is L. On the other hand flight path P' intercepts R' with length L'. R' is not the region to be studied, but a translation of the flight path P' to F' would result in the neutron intercepting R. The origin in P was arbitrary. For each neutron originating in P another could, with equal probability, have originated in P' with parallel paths. Hence consulting L' in R' towards the total flux is equivalent to starting a neutron at P'. Thus consideration of all regions symmetric to R with respect to …

It is desirable that a reactor exhibit a self-regulating effect. If this were not true any disturbance to the reactor would result in a continual increase in the magnitude of the disturbance and the reactor would be unstable. In this investigation the reactor is considered to have two reactivity feed-backs: metal temperature and water temperature reactivity effects. These two variables through a metal temperature coefficient and water temperature coefficient determine not only the reactor stability but also determine many operational characteristics.

The utilization of gloves wherein heavy element additives have been included is a significant means of reducing exposure to hands and, consequently, increasing allowable working time in operations which require direct contact with low energy isotopes - such as plutonium. The number of such gloves available has been limited considerably by the feasibility of fabrication and the practicality of application. The following study was made on two basic gloves - the first, a heavy zinc-neoprene coated glove and the second, a lead loaded neoprene glove available in two thicknesses. Included in the study was a standard 30 gauge neoprene glove.

It is being considered that the in-reactor portion of the test section of the PRTR Gas-Cooled Loop Facility consist, in part, of two concentric Inconel-X tubes. The outer tube is the main stress member, with 3.5 O.D. and a wall thickness of 0.065. The inner tube is 3.0 O.D. and has a wall thickness of 0.030. The inner tube provides an annular gas space to serve as thermal insulation.

"The PRTR Pressured Gas-Cooled Loop Facility, or Gas Loop, is an experimental facility to be installed in the Plutonium Recycle Test Reactor for use in studies contributing to advancement of the technology of gas-cooled reactors. The facility will provide an in-reactor loop for studying phenomena occurring under conditions likely to exist in gas-cooled reactors.

Various methods and procedures for preparing uranium dioxide bodies for metallographic examination and study have been utilized by various investigators. Unfortunately, these methods are not in general satisfactory for use on irradiated uranium dioxide. Since radiation damage studies on irradiated uranium dioxide require use of electron microscopy, and reveal structure by virtue of surface relief. This report covers an investigation of etching methods compatible with radiometallurgy and electron microscopy requirements.

By radiation dosimetry, we will mean the determination of the energy deposited per unit mass of irradiated material by ionizing radiation. Usually the material of interest in tissue and the results are to be applied to a radiobiological experiment, a radiotherapy treatment, or the protection of personnel from radiation hazards. The same methods, however, are applied to such engineering problems as the production of heat by reactor radiations, the use of radiation in chemical reactions or food processing, etc.

An inventory of the contaminated materials accumulated since the initiation of this project in June 1958, revealed a larger variety and quantity of materials that could be burned, than was specified for the initial scope. Therefore, it is desirable to revise the scope to permit handling the majority of these materials with the initially installed equipment.

The angular distribution of charged x mesons produced by 300 <x> 30 Mev neutrons on C12 and Be9 have been studied. An analysis of the kinematics for meson production in a nucleon-nucleon collision indicates a fairly well defined center-of-mass system.