Report presenting testing of two 2024-T3 aluminum-alloy multiweb wing structures (MW-2 and MW-3), similar to airplane or missile wings, at a Mach number of 2 under simulated supersonic flight conditions. Results regarding experimentally determined test conditions, model temperatures, strain-gage results, and model failures are provided. The report indicates that much of the stress data does not agree with expected results, but there is too much uncertainty regarding the reduction of strain data that no conclusions can be made concerning the results.

Report presenting a consideration of the problem of shaping an adjoining fuselage for a given wing and supersonic Mach number so that the combination will have a low wave drag. Only fuselages that can be simulated by singularities distributed along the body axis are studied.

Report presenting static-pressure changes resulting from steady combustion of aluminum borohydride in a supersonic wind tunnel. Static pressures were measured along the top wall of a tunnel adjacent to the flame that filled the upper portion of the test section. Results regarding the static-pressure increases, effect of change in fuel-injection rate, and effect of tunnel boundary layer on the character of the heat-addition region are provided.

Report presenting lift, drag, and pitching-moment coefficients, lift-drag ratios, and center-of-pressure positions for four airplane-like configurations determined from tests at a range of Mach numbers and angles of attack. The wings and nose shapes were modified for each of the configurations.

Report discussing high-speed cascade tests made of a blade section designed for conditions typical of the hub section of high-flow transonic rotors. The intent of the testing is to provide information on the effects of local surface Mach numbers on blade performance. The test results, effect of more forward location on peak surface velocities, effect of increase in pressure-rise coefficient, effect of Mach number and pressure rise on turning angle, and a comparison of variation in momentum-loss coefficient with surface pressure-rise coefficient are provided.

Report presenting an investigation to determine the effects of forging at 1950 degrees and 2150 degrees Fahrenheit as well as the effects of several heat treatments on the performance of Inconel 550 in a turbojet engine. Differences in engine performance of the different turbine blades could not be associated with consistent differences in microstructure or grain size. Results regarding blade performance, blade elongation during engine operation, microstructure of as-heat-treated blades, grain size, metallurgical studies of failed blades, stress-rupture tests, and hardness are provided.

Report presenting an investigation of the lateral stability and control effectiveness of a model of a fighter-type airplane model with a low-aspect-ratio and 3.4-percent-thick wing with negative dihedral at a range of Mach numbers, sideslip angles, and angles of attack. Results regarding the lateral characteristics at zero angle of attack, lifting conditions, and lateral and directional controls are provided.

Report presenting free-flight measurements of the rolling effectiveness and drag of trailing-edge spoilers on low-aspect-ratio wings with both laminar and turbulent boundary layers at two different Mach numbers. The effect of a spoiler deflected from the surface of a wing is to cause boundary-layer separation upstream.

Memorandum presenting rudder pulse maneuvers obtained with the Convair XF-92A delta-wing research airplane at an altitude of about 30,000 feet over a Mach number range of 0.52 to 0.92. Tests were made with and without a wing fence. By analyzing the maneuvers, the characteristics of the airplane transient, airplane stability derivatives, and frequency-response characteristics were measured.

Report presenting a rotating total-pressure survey rake to obtain wake measurements of a compressor rotor. Results indicated that there was a considerable radial flow of the inboard-blade boundary layer and little radial flow of the inner casing boundary layer. Results regarding the variation in total-pressure-loss distribution with Mach number, variation in total-pressure-loss distribution with angle of attack, contour plots, spanwise variation in total-pressure-loss coefficient, variation of low-speed momentum loss coefficient withe angle of attack, and variation of momentum-loss coefficient with Mach number are provided.

Report presenting an investigation to determine the overall performance of the modified eight-stage axial-flow compressor with new fourth-stage stator blades as part of a study of the problems encountered in a high-pressure-ratio axial-flow compressor with transonic inlet stages. The performance of the compressor was determined over a range of weight flows at equivalent speeds from 30 to 100 percent of design speed.

Report presenting measurements of the longitudinal stability, lift, and drag characteristics of an airplane configuration with a 60 degree delta wing and a swept horizontal tail mounted near the wing plane extended at a range of Mach numbers using the rocket-model technique. Comparisons are made to data form a similar model with the tail mounted above the wing plane.

Report presenting an investigation in the transonic tunnel to determine the effects of adding external, pylon-suspended stores to a model of the Douglas D-558-II research airplane. Tests were made for two spanwise store locations and covered a range of angles of attack and Mach numbers. Results regarding the drag, lift, and pitching-moment characteristics are provided.

Report presenting flight tests using a rocket-propelled 60 degree delta-wing body configuration, which included a NACA 0003-63 wing airfoil section. Drag at lift and stability data were obtained for a range of Mach numbers.

Report presenting flight tests to measure the directional stability of a fighter-type airplane over a range of Mach numbers. Testing occurred at two altitudes and used three vertical tails of varying aspect ratio or area.

The effects of inlet-air-flow distortions on the performance of the J65-B-3 turbojet engine were determined over a range of altitudes from 15,000 to 50,000 feet at a flight Mach number of 0.8. Radial inlet-air-flow distortions apparently do not affect the radial distribution of pressure after the first few compressor stages, while the circumferential inlet-air-flow distortion carried completely through the engine. For the distortions investigated, at rated exhaust-gas temperature and fixed-area exhaust-nozzle operation, the primary effect of the radial inlet-air-flow distortions was to reduce the engine air flow, and the primary effect of the circumferential distortion was to impose a temperature profile on the turbine, both resulting in reduction of thrust.

Report presenting zero-lift drag results for two 60 degree delta-wing configurations with air inlets. One had twin conical-shock semi-circular scoops just ahead of the wing-body juncture and one had a modified wing section over the inboard portion to allow installation of modified triangular inlets in the wing leading edge. Results regarding the drag coefficients and mass-flow ratios are provided.

Memorandum presenting an investigation to determine the static longitudinal stability contribution of a horizontal tail at two vertical locations behind a 4-percent-thick unswept-wing-fuselage combination at transonic speeds. The model used in tests is comprised of an unswept wing located in the midwing position on a body of revolution and a sweptback horizontal tail mounted on a vertical tail.

Report presenting an examination of creep and thermal buckling in order to determine their effect on the design of structures for high-speed aircraft. Consideration is given to the use of insulation as a means of alleviating the effect of aerodynamic heating. Creep did not appear to be a significant factor, but thermal buckling may have a substantial effect on the structural design.

Report presenting the gross weight and uranium investment of nuclear-powered, direct-air, shieldless, ram-jet missiles for a range of altitudes and Mach numbers. Results regarding the effect of reactor operating conditions and flight conditions on ramjet performance and effect of assumptions on ramjet performance are provided.

Report presenting an examination of the use of an axisymmetric variable-geometry technique for achieving good supersonic inlet performance over a wide range of Mach numbers. An inlet with a telescoping spike was designed and experimentally evaluated. Results regarding the spike survey study and variable-geometry-inlet study are provided.

Performance characteristics of a 16-inch annular-type combustor installed in a full-scale engine using gaseous-hydrogen fuel were obtained at simulated altitudes from 66,000 to 86,000 feet at a flight Mach number of 0.8. Combustion efficiencies of 86 percent were obtained at 86,000 feet (combustor pressure, 420 lb/sq ft abs). Combustor blowout was not encountered during the investigation.

Report presenting an investigation of the flutter characteristics of a series of thin cantilever wings with taper ratios of 0.6 for a range of Mach numbers. Results regarding flutter frequencies, time histories, effects of sweep on the flutter-speed ratio, effects of aspect ratio on the flutter-speed ratio, effects of additional models on the reference flutter speed, application of the flutter-speed ratio, and modified experimental flutter-speed coefficient are provided.

"An investigation to determine the static longitudinal and lateral stability characteristics of a 1/62-scale model of the Bell X-1A has been conducted in the Langley 9-inch supersonic tunnel. tests were made at Mach numbers of 1.62, 1.94, 2.22, 2.40, and 2.62 on the wing-body, wing-body-vertical-tail, and complete configurations. Data are presented for both the body and stability axes. Detailed analysis of the test results is omitted" (p. 1).