Abstract: Force, moment, and center of pressure information are presented for four models of the Hi-Lo configuration.

This report presents a description of and operating instructions for APOTA--a device which automatically tracks any signal-emitting source within the 190 to 250 MC band. APOTA is especially useful for telemetering applications.

Abstract: "This brochure presents a brief introduction to the Positional Tolerance Method of DImensioning as employed by Sandia Corporation. The emphasis is placed on the elimination of ambiguities and increase in tolerances provided by this method as compared to the older, bilateral method."

Abstract: Tests were made on 24 simply supported, post-tensioned, end-anchored, prestressed concrete beams with and without web reinforcement.

Specimens of two ferroelectric materials, barium titanate and lead-zirconate titanate, have been subjected to high dynamic stresses by impacting them with a projectile accelerated by an air gun. The purpose of these tests was to supplement information previously obtained using high explosives to stress the ferromagnetic materials.

Abstract: Results of pressure tests of a reflection plane in the Sandia 12-inch transonic wind tunnel to determine lateral and longitudinal Mach distribution over the plate at 0.5≤M≤1.30 are presented.

A plot of overpressure versus distance is presented for the fractional psi pressure level. The plot provides a rapid and simple means of estimating the permissible yield at any distance from settled areas.

Abstract: Methods are presented for calibrating a peak current gage which was developed at Sandia in the spring of 1953.

Abstract: This document outlines the essentials of the planning and action necessary for the recovery of radioactive contaminated equipment following a radiological disaster. It lists the records which should be collected before a disaster and discusses the training of personnel for recovery teams. Radiation doses, radiation indicators, and protective clothing are all treated in a general fashion. Procedures are given for the actual recovery of equipment, with emphasis on personnel safety. Decontamination techniques and materials are then discussed. Graphs and simple calculations are presented for determining safe work limits and radiation doses under varied conditions. A list of typical sources for radiological supplies and a brief bibliography are also included.

From abstract: This paper presents the results of a study of the error in radio interferometer measurements of near sources attributable to the use of asymptotic formulae, valid for distant targets.

From introduction: This report describes the procedures used and the results obtained in evaluating the Wiancko type 3-PBM-2 microbarograph system.

Abstact: "Wind tunnel tests were performed to determine pressure distributions and normal force coefficients on three block forms on mounting planes. The dimension ratios of the blocks were 1:1:1, 1:1:2, and 1:1:4. Results are given for variation in Mach number from 0.066 to 0.8, in Reynolds number from 0.28 x 10(exp 6) to 4 x 10(exp 6), and in yaw angle from 0 to 90 degrees. Results show a Reynolds number independence over the range examined. Windward face force coefficients for a given block form are approximately proportional to the ratio of impact to dynamic pressure. Pressure distribution and resultant coefficients are affected by mounting planes."

Abstract: "An exploding copper wire, one millimeter in diameter, 30 centimeters long, has been developed as a fuse component for a Los Alamos capacitor energy source to be employed in controlled thermonuclear research studies. The fuse allows the passage of the high normal duty "action" (13,700 ampere-coulombs per capacitor) at a 20-second repetition rate. However, it interrupts the circuit to a shorted capacitor in 12 microseconds, thereby protecting the faulted capacitor from explosive energy consumption. The initial phase of the development included observations of various metals (copper, silver, iron, and nickel) as well as various configurations (straight wires, helixes, foils, and tubes). Direct scaling of previous small exploding wire studies at Sandia Corporation was demonstrated with scaling factors up to 700,000."

From scope of work: This report investigates the dynamic characteristics of sealed military type relays as affected by applied coil voltage and/or current, temperature, spring tension, contact force, contact overtravel, and mechanical clearances.

Abstract: "The pressure drop associated with the flow of air through a cylindrical bed of spherical pebbles has been investigated experimentally. The results of this investigation are reported here."

Abstract: "The excellent agreement between measured boundary layer thickness and thickness calculated by Sivells and Payne recommends their method for calculating turbulent boundary layer growth in axisymmetric hypersonic nozzles. It was thought worthwhile to adapt their approach to the laminar boundary layer. This analysis, along with a limited amount of corroborating data, is presented herein."

The following report describes the purpose and usage of the tolerance comparator, and Sandia Corporation's investigation of the drafting practice leading to the aid.