An investigation was conducted in the NACA Lewis 10- by 10-foot supersonic wind tunnel to evaluate the performance of three burner configurations in a 16-inch ram jet with gaseous hydrogen as fuel. Data were obtained over a fuel-air-ratio range from 0.0030 to 0.0260 (stoichiometric = 0.0292) at a free-stream Mach number of 3.0 and 0 degree angle of attack. The exit nozzle-throat area ratios employed were 0.60 and 0.75.

Results of a survey investigation of the J71-97 experimental three-stage turbine equipped with a first-stator area 70 percent pf design are presented and compared with the turbine with a first-stator area 97 percent of design.

An evaluation of the effect of geometric design variables on the performance of a 16-inch-diameter ram-jet combustor total pressures from 7 to 44 inches of mercury absolute. Equivalent ratio was varied from 0.1 to 1.0 at a combustor inlet temperature of 1100 degrees R.

Report presenting an experimental determination of the flow fields near swept- and unswept-wing-fuselage combinations at zero sideslip as determined experimentally at low speed for various spanwise and vertical locations and angles of attack as variations with chordwise distance. Results regarding the swept-wing-fuselage flow fields, unswept-wing-fuselage flow fields, and a comparison of wing-fuselage and fuselage-alone flow fields are provided.

Internal performance of normal-shock rectangular, circular, and scoop inlets and of external-compression inlets experimentally obtained with varying immersion in a turbulent boundary layer. Recoveries varied from about 95 percent of theoretical in the free stream to 80 percent with complete immersion, while the corresponding mass flows were usually above 95 percent of theoretical. Turning of the flow through 10 degrees caused losses in pressure recovery of 0.03 to 0.07. External compression did not improve pressure recovery in the boundary layer. Average distortion at critical operation for all inlets was 5 percent.

Memorandum presenting an investigation to determine the drag, longitudinal stability, and lateral stability characteristics of a model of a fighter-type airplane. Several modifications were made to the model in an attempt to eliminate pitch-up.

Boundary-layer-transition and heat-transfer measurements were obtained from flight tests of blunt and sharp cones having apex angles of 50 deg. The test Mach number range was from 1.7 to 4.7, corresponding to free-stream Reynolds numbers, based on cone base diameter, of 18. 3 x 10(exp 6) and 32.1 x 10(exp 6), respectively. Transition on both models occurred at a local Reynolds number of 1 x 10(exp 6) to 2 X 10(exp 6) based on distance from the stagnation point. Transition Reynolds numbers based on momentum thickness were between 320 and 380 for the blunt cone. The model surface roughness was 25 rms microinches or greater. Turbulent heat transfer to the conical surface of the blunt cone at a Mach number of 4 was 30 percent less than that to the surface of the sharp cone. Available theories predicted heat-transfer coefficients reasonably well for the fully laminar or turbulent flow conditions.

"A highly polished hemisphere-cone having a ratio of nose radius to base radius of 0.74 and a half-angle of 14.5 degrees was flight tested at Mach numbers up to 4.70. Temperature and pressure data were obtained at Mach numbers up to 3.14 and a free-stream Reynolds number of 24 x 10(exp 6) based on body diameter. The nose of the model had a surface roughness of 2 to 5 microinches as measured with an interferometer" (p. 1).

Report presenting testing on six blunt-nose models at angles of attack ranging from 0 to 5 degrees in order to evaluate the heat transfer and pressure on their surfaces. Information about transition, proper design, and locations of greatest and least heat transfer is provided.

"Measurements of aerodynamic heat transfer have been made along the hemisphere and cylinder of a hemisphere-cylinder rocket-propelled model in free flight up to a Mach number of 3.88. The test Reynolds number based on free-stream condition and diameter of model covered a range from 2.69 x l0(exp 6) to 11.70 x 10(exp 6). Laminar, transitional, and turbulent heat-transfer coefficients were obtained" (p. 1).

Report presenting testing of four models of a thin magnesium fin, with the leading edge swept back 35 degrees, of a type used to stabilize the first stages of rocket-propelled multistage hypersonic models. The investigation was carried out to determine some effects of aerodynamic heating at high stagnation temperatures on the leading edges of fins and to determine the relative effectiveness of several leading-edge protective methods. The fins tested included a basic fin, a fin with a blunt leading edge, a fin with a blunt leading edge wrapped with Inconel, and a fin with a blunt leading edge made of stainless steel.

Turbojet thrust augmentation with fuel-rich afterburning of hydrogen, diborane, and hydrazine was computed. Results regarding takeoff thrust augmentation and flight thrust augmentation are provided.

From Introduction: "This report presents net thrusts computed for hydrogen, diborance, and hydrazine with fuel-air ratios form stoichiometric values to 0.5. Net thrusts for fuel-rich afterburning are compared with those for stoichiometric combustion of the turbojet fuel and air augmented with a 220-second specific-impulse rocket."

Memorandum presenting an analysis of one-spool ducted-fan engines in order to determine the primarily limitations on ducted-fan-engine design and to compare this type with the turboprop and turbojet engines for the same application. Designs were studied at flight Mach numbers of 0 and 0.6 at sea level and Mach numbers of 0.6 and 0.8 at the tropopause. Results regarding the discussion of charts, effect of design parameters on turbine stress, effect of design parameters, effect of design parameters on thrust specific fuel consumption, and effect of design parameters on thrust per unit total weight flow are provided.

Memorandum presenting a study of six nine-element injectors for the liquid-oxygen-heptane propellant system in an 1800-pound-thrust rocket engine. The characteristic velocities for comparable injector types were about the same as those obtained from the two-element study. The level of performance was generally higher for the nine-element injectors.

Memorandum presenting a low-velocity-turning stator designed to reduce secondary-flow loss cores by turning the flow at low velocities and accelerating it in passages of constant flow angle with reduced cross-channel pressure gradients. Performance of the stator was determined with static-pressure measurements and detailed surveys of total pressure and flow angle made with the turbine operating at design speed near design work.

Report presenting a low-velocity-turning stator designed to reduce secondary-flow loss cores by turning the flow at low velocities and accelerating it in passages of constant flow angle with reduced cross-channel pressure gradients. Turbine performance was measured to determine the effect of low-velocity turning in the stator on the overall turbine performance. Results regarding the stator performance, overall turbine performance, and rotor exit surveys are provided.

Report discussing an investigation into the binding of amorphous carbon with flourine to render it inert and easy to vent into the atmosphere.The ease and safety of the procedure are described.

Memorandum presenting an experimental investigation showing that amorphous carbon, such as wood charcoal, is readily applicable to fluorine disposal by a specified chemical reaction. Fluorine and fluorine-oxygen and fluorine-nitrogen mixtures containing as little as 6.5 percent fluorine reacted spontaneously with fresh dry charcoal.