From Introduction: "In the present paper, which supplements reference 1, V-g records obtained from F8F-2 airplanes in 1949 are analyzed statistically to determine the frequency of experiencing large values of normal load factor and airspeed. These results are compared with the results from the F8F-1 airplane."

Report presenting general procedures for computing internal pressures in fuel tubes of nuclear reactors and the effects on the pressure of varying neutron flux, fissioning material, and operating temperature.

Report presenting free-flight tests made with four fin-stabilized bodies of fineness ratio 8.91 to determine the effect of body cross-sectional shape on body drag at a range of Mach and Reynolds numbers. Results regarding the curve of drag coefficients, drag on the nose and body, and body pressure drag are provided.

"Tests have been made at the Langley Aeronautical Laboratory on a 6000-horsepower propeller dynamometer installed at a ground test facility to determine the effect of a half-scale model of the Wright Aeronautical Development Center 30,000-horsepower whirl rig upon the aerodynamic characteristics of a three-blade NACA 10-(3)(062)-045 propeller. The model of the whirl rig was mounted in front of the 6000-horsepower propeller dynamometer. Static propeller tests were made for 0deg, 5deg, 10deg, 15deg, and 20deg blade angles over a range of rotational speeds from 600 to 2200 rpm in 100-rpm increments" (p. 1).

Report that is part of a program to investigate the aerodynamic characteristics in pitch, yaw, and steady roll of various model configurations with variations in the wing geometric parameters. The paper presents the aerodynamic characteristics in pitch of wing-fuselage combinations with wings of aspect ratio 4, taper ratio of 0.6, and sweep angles varying from 3.6 degrees to 60 degrees. Results regarding lift characteristics, pitching-moment characteristics, drag characteristics, and lift-drag ratios are provided.

From Introduction: "The purpose of the present paper was to determine whether the characteristics about a skewed axis could be predicted from data about the normal angle-of-attack axis, and whether such a configuration offered any aerodynamic advantages over the conventional hinge location normal to the pane of symmetry."

Report presenting an attempt to determine the reliability and calibration of the Langley transonic tunnel in the open slotted test section. Results regarding test-section calibration, including flow uniformity, calibration, and angularity, model testing and boundary interference, and reduction of interference are provided.

Report presenting an adhesive, FPL-710, which produces higher strength at temperatures up to 600 degrees Fahrenheit than previously obtained and possesses good resistance to aging at high temperatures. It also has acceptable resistance to creep and immersion in various organic solvents. Results regarding its strength properties, heating and aging resistances, and variables affecting bond strength are provided.

Report presenting an investigation to determine the effects of camber on the aerodynamic characteristics of a series of rectangular wings with various aspect ratios and thickness-to-chord ratios using the transonic-bump method. Testing occurred over a range of Mach and Reynolds numbers. Lift, drag, and pitching-moment characteristics are presented for wings of 5 aspect ratios, NACA 63A2XX and 63A4XX sections, and 5 thickness-to-chord ratios.

From Introduction: "The supersonic axial-flow compressor, for example, appears to offer advantages of high stage pressure ratio and height weight flows (reference 1) but problems peculiar to this compressor type have accompanied its introduction. For high single-stage pressure ratios (>4) the problem of converting the high dynamic energy to useful pressure arises (reference 2). In addition, the high tip speeds and weight flows combine to create a difficult situation for the turbine designer."

Report presenting a wing-body combination with a plane tapered wing of aspect ratio 3.1, taper ratio of 0.39, and 3-percent-thick, rounded-nose sections in streamwise planes at subsonic and supersonic Mach numbers. The lift, drag, and pitching moment are presented for a range of Mach numbers and Reynolds numbers.

Report presenting an investigation to determine the overall performance of the three-stage turbine from the J71 turbojet engine. The turbine operated with a maximum brake internal efficiency of approximately 0.84 at an equivalent overall pressure ratio of approximately 3.6 and an equivalent rotor speed of about 110 percent of the equivalent design value.

Report presenting an investigation in an altitude test chamber to evaluate the performance of an axial-flow turbojet engine over a range of engine-inlet Reynolds numbers. Reducing the engine inlet Reynolds number resulted in a reduction of corrected air flow and compressor efficiency but did not affect the compressor pressure ratio at a given corrected engine speed.

Report presenting measurements of lift made on various rectangular-plan-form wings differing in trailing-edge thickness, profile shape, maximum thickness ratio, and aspect ratio. Experiments were conducted at a range of Mach numbers, Reynolds numbers, and wings with and without boundary-layer trips. Results regarding a comparison of experimental results with theory at moderate supersonic Mach numbers and calculations for hypersonic Mach numbers are provided.

Report presenting a study of the literature data on the solubility of water in hydrocarbons, which includes information about the log of solubility, critical solution temperature, and ratios that may affect solubility are provided. An equation is presented and applied to a few petroleum fractions ranging from gasoline to lubricating oil, and a comparison of calculated and experimental solubilities is provided.

From Introduction: "Design studies of long-range supersonic missiles indicate the Mach number range of 3 to 4 to be of considerable promise. Accordingly, the NACA is conducting research on the performance of a wide variety of supersonic diffusers in this range. The initial phase of this research is concerned primarily with the characteristics of conventional axially symmetric diffusers operating at design values of flight Mach number."

Report presenting an investigation at transonic speeds to determine the control characteristics of a linked flap and spoiler. The control consisted of a linked combination of a quarter-span inboard plug-type spoiler and a full-span flap. Results regarding the hinge-moment, pitching-moment, lift, and rolling-moment are provided.

From Summary: "Force characteristics determined from tank tests of a 1/5.78-scale model of a hydro-ski-wheel combination for the Grumman JRF-5 airplane are presented. The model was tested in both the submerged and planing conditions over a range of trim, speed, and load sufficiently large to represent the most probable full-size conditions."

Report presenting a wind-tunnel investigation to determine the effects of two wing-root leading-edge plan-form modifications, including a notched leading-edge fillet and a rounded leading-edge fillet, on the low-speed longitudinal stability characteristics of an airplane model with a 50.7 degree sweptback wing. Results regarding stability at zero lift, variation of stability with lift coefficient, and lift and drag characteristics are provided.

Report presenting an investigation to determine the effects of dual-rotation propeller operation at high thrust on the static longitudinal stability characteristics of a semispan powered model representing a twin-engine airplane configuration with flaps retracted. Stability and trim changes associated with an extreme constant power conditions were greatly dependent on tail height and vertical location of the center of gravity. Results regarding basic data, effects of power on overall stability and trim, and tuft-grid flow surveys are provided.

Report presenting analytical methods to calculate average and local turbine-blade temperatures. The temperatures were compared with experimental data obtained in a forced-convection, water-cooled aluminum turbine over a range of turbine-inlet-gas temperatures and coolant-mass velocities. Results regarding comparison of calculated and experimental aluminum turbine blade temperatures, comparison of calculated and experimental stationary-blade temperatures, stationary water-cooled blade operating data, and turbine operating data are provided.

Report discussing an investigation using rocket-propelled vehicles in free flight to determine the effect of fuselage-diameter - wing-span ratio on the damping-in-roll characteristics of delta wings at a range of Mach numbers. The damping-in-roll derivative was found to decrease when the fuselage-diameter - wing-span ratio was increased. The experimental results are compared to calculated values.

"An experimental investigation in the Langley Gas Dynamics Laboratory has been made of the flow separation from slender rods mounted to extend forward along the axes of symmetry of blunt-nosed bodies. The mechanism of the separation and its governing criteria are discussed. Drag data at a Mach number of 2.72 for various rod lengths and nose radii at an angle of attack of zero degrees are presented. It was found that the drag coefficients of blunt noses could be appreciably reduced by the use of protruding rods. Criteria for rod length which gives lowest drag are given" (p. 1).

Report presenting an investigation to determine the characteristics of a double-shroud cooling-air ejector. The performance of a single-shroud ejector with a clamshell-type variable-area actuating nozzle was compared with that of an ejector having a conical nozzle. Results regarding the mechanics of ejector flow systems, effect of variable-area primary nozzle on ejector performance, double-shroud-ejector performance, and application of data are provided.