Report presenting a free-flight investigation of two rocket-powered model configurations to determine the damping in roll. The model had rectangular wings of 4.5 aspect ratio and were the same except for the airfoil sections. Results regarding rolling velocity and total-drag coefficient are provided.

"An investigation has been conducted in the Langley 20-foot free-spinning tunnel to determine the spin and recovery characteristics of a 0.057-scale model of the modified Chance Vought XF7U-1 airplane. The primary change in the design from that previously tested was a revision of the twin vertical tails. Tests were also made to determine the effect of installation of external wing tanks" (p. 1).

Report presenting testing of two NACA two-blade propellers at a range of blade angles and Mach numbers. The effect of compressibility and design section camber are presented for each propeller. The results indicated that if the outboard sections of a propeller are the thinnest, the design of the propellers should incorporate loading distribution that is concentrated in the tip sections.

Report presenting an investigation in the 4- by 4-foot supersonic tunnel to determine the static longitudinal stability and control characteristics of a supersonic aircraft configuration at a Mach number of 1.59. The model had a 40 degree sweptback tapered wing with 10-percent-thick circular-arc sections normal to the quarter-chord line.

Report presenting the results from several recent flights on the Northrop X-4 No. 2 airplane, including the longitudinal stability characteristics over a range of Mach numbers in straight and accelerated flight and the short-period longitudinal-oscillation characteristics.

Report presenting testing of the rolling effectiveness and drag of half-delta wing-tip ailerons on rectangular and tapered wings sweptback 0 and 45 degrees for a range of Mach numbers. The rolling effectiveness was relatively uniform across the Mach number range and was lower at subsonic speeds and higher at supersonic speeds than the partial-span plain ailerons.

Report presenting the longitudinal and lateral characteristics of a wing-fuselage combination with a wing with the leading edge swept back 63 degrees and cambered and twisted for a uniform load at lift coefficient 0.25 and Mach number 1.5. The investigation occurred over a range of sideslip angles. The results indicated that the longitudinal characteristics were essentially unaffected by Reynolds number or the sideslip angles investigated.

Report discussing an investigation of two transonic research airplane models at a range of Mach numbers and Reynolds numbers. The main difference between the models was the aspect ratio of the horizontal tail. Results regarding the stability, control, incremental horizontal-tail characteristics, downwash, horizontal-tail load, stability factors, and a tailless configuration are provided.

"Time histories are presented of horizontal-tail loads, elevator loads, and deformations on a jet-powered bomber during abrupt pitching maneuvers at a pressure altitude of approximately 20,000 feet. The normal and pitching accelerations measured varied from -0.90b to 3.41g and from -0.73 to 0.80 radian per second per second (sic), respectively, with a Mach number variation of from 0.40 to o.75. The maximum horizontal-tail load measured was 17,250 pounds down. The maximum elevator load was 1900 pounds up. The stabilizer twisted a maximum of 0.76 degrees leading edge down at the tip. The greatest fuselage deflection at the tail was about 1.7 inches down" (p. 1).

From Introduction: "The performance of several tail-pipe burners with fixed area exhaust nozzles is reported in references 1 to 4, and the performance of an NACA-designed tail-pipe burner with a variable-area exhaust nozzle is reported in reference 5. Operational characteristics of the tail-pipe burner are also discussed."

Report discussing the division of load among the wing, fuselage, and tail for several aircraft configurations at subsonic and supersonic speeds. The load that each component carries at various Mach numbers and angles of attack is described.

"A camera designed for use in flight has been developed by the NACA Lewis laboratory to photograph cloud droplets in their natural suspension in the atmosphere. A magnification of 32 times is employed to distinguish for measurement purposes all sizes of droplets greater than 5 microns in diameter. Photographs can be taken at flight speeds up to 150 miles per hour at 5-second intervals, A field area of 0.025 square inch is photographed on 7-inch-width roll film accommodating 40 exposures on an 18-foot length" (p. 1).

Report presenting the results of pressure-distribution and force tests on four wings at Mach number 6.86 and Reynolds number 980,000 in the 11-inch hypersonic tunnel. Characteristics of the wings tested included a 4-inch square plan form, a 5-percent maximum thickness, and diamond, half-diamond, wedge, and half-circular-arc sections. Information about pressure measurements, wing characteristics, and Schlieren photographs is provided.

"A simple apparatus particularly applicable to the determination of the corrosive effects of flowing liquid metals on structural materials is described. In this apparatus, flow of the liquid medium at known velocities may be induced in toroidal shaped channels fabricated from the test structural material only, with no pump, valves, or flow meter required. A circulating velocity of 25 ft/sec has been obtained in preliminary tests and no basic limitation on increasing the speed was encountered" (p. 1).

Report presenting buffet boundaries, buffeting-load increments for the stabilizers and elevators, and buffeting bending-moment increments for the stabilizers and wings for a jet-powered bomber airplane equipped with reflexed flaps and ailerons and tail-tip-incidence changes.

"A General Electric fuel and torque regulator was tested in conjunction with a T31-3 turbine-propeller engine in the sea-level static test stand at the NACA Lewis laboratory. The engine and control were operated over the entire speed range: 11,000 rpm, nominal flight idle, to 13,000 rpm, full power. Steady-state and transient data were recorded and are presented with a description of the four control loops being used in the system" (p. 1).

Report presenting an investigation of a wing-body combination with a plane triangular wing of aspect ratio 4 and 3-percent-thick rounded nose sections in streamwise planes at subsonic and supersonic Mach numbers. Lift, drag, and pitching moment are presented for a range of Mach and Reynolds numbers.

Report discussing an investigation to determine the aerodynamic characteristics of a model of a tailless delta-wing airplane configuration with a leading edge swept back 60 degrees at a range of Mach numbers. Information about lift-curve slope, buffeting, drag rise, hinge-moment coefficients, transonic trim, and stability is provided.

"Forced-convection heat-transfer data have been obtained for water flowing in an electrically heated tube of circular cross section at water pressures of 200 and 2000 pounds per square inch, and temperatures in the nonboiling region, for water velocities ranging between 5 and 25 feet per second. The results indicate that conventional correlations can be used to predict heat-transfer coefficients for water at pressures up to 2000 pounds per square inch and temperatures in the nonboiling region" (p. 1).

Report presenting experimental force and moment data obtained by pressure measurements on a wing of aspect ratio 8.02, 45 degree sweepback of the quarter-chord line, taper ratio of 0.45, and NACA 63(sub 1)A012 airfoil sections, which are compared with the calculated loadings obtained by standard methods and several variations of the methods. Results regarding the system of identifying solutions, spanwise load distribution, lift-curve slope, center of pressure, wing pitching moment, and induced drag are provided.

Report presenting an investigation to determine the effect of varying the span and deflection angle of a 15-percent-chord slat on the longitudinal aerodynamic characteristics of a semispan wing with 49.1 degrees of sweepback at the leading edge, an aspect ratio of 3.78, a taper ratio of 0.586, and NACA 65A006 airfoil sections. Force measurements and chordwise pressure distributions were obtained on the wing and extended slat with and without a deflected trailing-edge flap.

Report presenting an investigation of liquid-film cooling at a variety of air temperatures and Reynolds numbers. Results regarding the effect of coolant flow per circumferential length on liquid-cooled length, correlation of heat transfer from hot gas to liquid film for constant coolant flow per circumferential length, and generalized plot of film-cooling data based on heat-transfer correlation at constant coolant flow per circumferential length are provided.

Report presenting the lateral-control characteristics of two spans of spoiler and flap-type ailerons on an unswept wing with an aspect ratio of 2.5 and hexagonal airfoil sections. Measurements of rolling moments, yawing moments, aileron hinge moments, normal forces, and balance-camber pressures for various configurations of the wing.

The performance characteristics of a downward canted normal-shock side (scoop) inlet located downstream of a triangular control surface are presented for free-stream Mach numbers of 1.5 and 1.8 in terms of total pressure recovery and mass flow ratio for various boundary-layer removal systems, angles of attack, control surface deflections and adverse yaw. An engine operating condition for a hypothetical turbojet engine is established, and the match point characteristics of the engine-inlet configuration are summarized. It is shown that the diffuser performance increases with increased boundary-layer removal and decreases because of the presence of the wake from the forward control surface.